set clock DACIA SOLENZA 2004 Repair Manual

19
19 - 7
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles without air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clips the oil reservoir of the power steering from the battery screen.
Disconnect the engine fan connector ( 1) and detach from clips wiring of point ( 2)
Dismount the four attachment screws ( 3) of the engine fan on radiator.
Carefully dismount the engine fan assembly from guiding points (4).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully position the engine fan assembly in the guiding points (4).
Mount the attachment screws ( 3) of the assembly on the radiator.
Connect the engine fan connector ( 1).
Attach in clips the wiring in point ( 2).
Attach in clips the power steering oil reservoir on the battery screen.
Mount the air inlet pipe.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, e lectronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client.
Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

19
19 - 9
COOLING - EXHAUST - TANK
Cooling engine fan for vehicles with air conditioning
DISMOUNTIN G
Disconnect the battery (-) terminal.
Remove the air inlet pipe from the attachment of the battery screen.
Detach from clip the power steering oil reservoir from the battery screen.
Disconnect the engine fan connector ( 1)
Detach wiring from clips ( 2) and (3).
Disconnect the connector of the cooling engine fan resistance (4).
Carefully dismount the engine fan assembly from the radiator, from sustaining points (5).
REMOUNTING
Check the condition of the fan impeller and of the engine fan electric motor.
Carefully mount the engine fan assembly in the sustaining points (5).
Connect the connector of the engine fan resistance ( 4).
Connect the cooling engine fan connector ( 1) and attach it in clip (3) then in clip (2).
Attach in clips the power steering oil reservoir on the battery screen. Mount the air inlet
pipe.
Connect the battery (-) terminal. In case the vehicle is equipped with programmable
r adio-cassettes player, electronic clock, etc, there are t o be re-programmed before returning
the vehicle to the client. Check the engine fan operation: start the vehicle engine and disconnect the water
temperature sensor. The engine fan must start. Reconnect the water temperature sensor
then by means of the CLIP tester erase the memorized failure corresponding to the water
temperature sensor.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 3
DISMOUNTING
After identification and elimination of the real cause of the battery discharging, proceed as
follows: Remove the plastic protector from the plus plug of the battery.
Dismount the attachment nut of the mass wiring from the minus plug of the battery.
Dismount the attachment nut of the wiring from the plus plug of the battery.
Dismount the battery attachment clamp screw.
Carefully take off the battery.
R EMOU NT I NG
Perform the dismounting operations in the reverse order. After that, reset the radio by intro-
ducing the radio code (if the vehicle is equipped with radio) and adjust the dashboard clock.
Battery
vnx.su

84
STEERING - CONN ECTOR
84 - 4
Under steering wheel control
R EMOU NT I NG
Ensure that steering is on middle point (wheels are in the straight-on driving position of the
ve h icle).
Position the under-steering wheel control assembly so that after remounting the two steering
wheel half-cases, the assembly handles are lined up with the instrument panel and the dashboard.
Reconnect the windscreen wiper connector, the lights and turning connector and the rotating
contact connector. Attach in clips the steering wheel half-cases.
Tighten t he screw ( 2) so that i s blocking the under-steering wheel control on the steering
column. This operation is facilitated by a cutting-out in the lower half-case allowing the access to
the screw ( 2).
Carefully mount the steering wheel in order not to damage the “tape” connector of the rotating
contact, the steering wheel is having an area with no grooves, that must be corresponding to the
no-grooves area from the steering column. The steering wheel must easy enter in the grooves.
Replace the steering wheel attachment screw (TORX 50) after each dismounting and tighten
it to the required moment ( 4.4 daNm).
Reconnect the airbag connector (10.
M ount the two attachment screws TORX 20 of the airbag (required tightening moment is
0.65 daNm) Reconnect the battery (-) terminal.
Check the operation of the under steering weel control.
IMP ORTANT !
Before reconnecting the driver’s ai rbag connector, it is necessary to apply a check-
ing procedure of the system: - check if the airbag indicator from the instrument panel is on, when the contact
is set on; - connect the inert igniter to the airbag connector (to the wiring) and check if the
airbag indicator is off; - set the contact off, connect the airbag connector instead of the inert igniter and
attach the airbag on the steering wheel (required tightening m oment is 0.65 daNm). AT T E N T I ON !
Any doubts regarding a good centering of the rotating contact involves the applying
of its centering method: carefully rotate clockwise the upper part of the rotating con-
tact 2.5 complete rotations (or until it gets blocked), then rotate anti-c lockwise 2.5
complete rotations. In case of a steering dismounting operation, of t he engine or of the t ransmission
elements implying the steering rack or steering column uncoupling, the steering wheel
must be immobilized. After everything has been remounted, perform an airbag system checking by means
of the CLIP tester. If everything is correct, unblock the UCE airbag and check if the
airbag indicator from the instrument panel is on for 3 seconds from setting the contact
on, then it is off and is remaining off. If the airbag indicator is not operating as a.m .,
see chapter “Diagnostic” and check the system by means of the “CLIP” tester. AT T E N T I ON !
All non-observing of these prescriptions may c ause an abnormal operation of the
sy stem, even an undesirable starting of it.
vnx.su