belt DACIA SUPERNOVA 2004 User Guide

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
Tightening couples (daNm)
Screws of wheels7.5
Screw of the crankshaft pulley 2+68
o+/-6o
S crew-nut of stretching runner 5
Screws right-side stand 6.2
Screw-nut hydroelastic buffer 3.7
DISMONTING
The car is placed on a lifting stand.
The fore part of the engine is proppe d
on the frame using the MOT.545 device.
The following are taken apart: -front right-side wheel;
-the right-side pendular suspension;
11 - 1 -the alterna tor belt;

-the carrying belt of the compressor
(AC) ;
-the pulley of the crankshaft and its hub;
-the carryi ng pulley of the compressor;
-the distri bution crankcases.
DIS TRIBUTION BELT
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
The engine is set at the tuning point (see Chapter 10, pages 10-19);
The screw-nut of t he stretching runner i s loosened;
The distri bution belt is taken off.
R
E-MOUNT ING
A new distribution belt is mounted ( see Chapter 10, pages 10-33);
The tension in t he di stribution belt is checked and a djusted, by m eans of MOT.1505
device, at the value of 145-185 Hz.
The opera tions are done in the reverse order of those in the dismantling process;
The screws are tightened at the couple;
It is c ompulsory t o tighten the crankshaft pulley a t a 2 daNm couple plus a n angle of
68
o+/-6o;
The compressor pulley ( AC) is re-mounted;
The be lt of the alterna tor a nd that of the compre ssor are stretched, oberving the
values of the mounting tension:
Alternator: 263 Hz+/- 10%
Co mpressor: 222 Hz+/- 10%.
11 - 2
DISTRIBUTION BELT
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
SPECIAL TOOL- AND-CHECK SETS
MOT.1202-01 -”CLIC” collar-pincers
MOT.1505 -Device for measuring belt tension
MOT.484 -Device for jacket maintaining -Wrench for angular tightening
-Pincers for elastic collar
TIG H TENING CO UPL E S (daNm )
S crew-nut of stretching runner/pulley 5
Screw of crankshaft pulley 2+68
o+/-6o
Screws of pendular suspension stand 6.2
Screw-nut of hydro-elastic buffer 3.7
Wheel Screws 7.5
Co mbustion-head Screws 2+97
o+/-2o
To take apart :
-the connector of the induction coil;
-the fue l hoses (t he going- and re -
turn circ uit); -the connectors of the injectors;
-the plugs of the sparks;
-the induction coil.
11 - 3
CYLINDER HEA D FITTING
D
IS M O UNT ING
The car is placed on a two-column lift -
ing stand; The battery i s disconnected;
The cooling circuit is emptied at the
jack situated at the lower pa rt of the radia-
tor; The distribution belt is taken apart (see
Chapter Distri bution Belt);
The following are taken apart: -air-filter;
-the c onnector of the c lapper-posi-
tion potentiometer (1); -the acceleration cable;
-the connector of the atmosphe ric
pressure sensor (2);
-the co nnector of the step-by-step
engine (3); -the connector of t he air temperature
sensor (4) on the intake collector;
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
RE-MOUNT ING
The plane of the fitting is cleaned and checked.
Mount the cylinder he ad with a new gasket.
The taking-apart opera tions are done in the reverse order.
The combustion-head is tightened ( see Chapter 10, pages 10-31).
The distri bution belt is mounted ( see Chapter 10, pages 10-33);
It is mounted in the reverse order of the taking-apart process;
The filling-up and the airing of the cooling circuit is done ( see Chapter “Filling-up
and draining” );
The rocker-arms are adjusted.
NOTE
At each operation requiring battery disconnection, when reconnecting, introduce
the radio code, which is written on the vehicle-buying invoice.
11 - 5
CYLINDER HEA D FITTING
vnx.su

16E7J-A-2/60 ENGINE
16 - 2
ST ARTING AND CHARGING
B.The light turns on when the engine is running
This indicates a charging fa ult, the cause of which may be: - the carrying belt of t he alternator i s broken, the charging conductor i s cut (+ con-
tinuous); - a fault with the alternator (rotor, stator, diodes or brushes);
- a fault with the voltage regulator;
- a voltage surge (overvoltage).
C. The customer / user claims a fault with the charging, as the
on-board light works correctly.
If the re gulated voltage is less than 13.5 V, the alternator is checked. The cause of the defect may be:
- a burnt diode;
- disconnected or cut live wire;
- the coal powder or the wear of the collector.
C
ONTROL OF VO LTAG E
A voltmeter is connected across the terminals of the battery and the voltage value is
read.
The engine is run until the needle of the voltmeter settles at the regulated voltage. This value should be within 13.5 and 14.8 V.
The maximum of consumer devices are connected: the voltage should remain between 13.5 and 14.5 V.
CAUTION!
In case electric arc welding i s being done on t he car, the battery and t he voltage
regulator will be compulsorily disconnected (t he alternator).
AL TERNATOR
vnx.su

E7J-A-2/60 ENGINE16
16 - 3
ST ARTING AND CHARGING
DIAGNOSING
Special device: Tester CLIP - SAGEM and accessories for physical measurements.
I
NSPE CT ION OF CHARG ING CIRCUIT
The CLI P - SAGEM tester allows the inspection of the alternator, by measuring the volt-
age and the curre nt supplied with, and without electri c consumers.
NOTE: The Ampere pincers are of the inductive type (0-1000 A). Its mounting
wi ll be done without disconnecting the battery, thus allowing for the memorized
da ta and the adapting values in the injection calculator to be preserved.
M ount the ammeter clamps directly to t he alternator exit, having the arrow oriented
towards this one
.
The measurements are effected in thre e steps: - measuring the battery voltage without contact on;
- measuring the regulated voltage and the current supplied without consumers;
-
measuring the regulated voltage and the current supplied with a maximum of consumers.
The values obtained as a result of t he measurements lead to the following interpretations: -the voltage of t he ‘empty’ battery < 12.3 V: so, the battery is flat;
With no consumers: -regulated voltage > 14.8 V: so, the regulator is faulty;
-regulated voltage (‘empty’) < 13.2 V or charging current < 2 A: so, there is a defect
of charging. With consumers: -regulated voltage > 14.8 V: so, the regulator is faulty;
-regulated voltage (‘empty’) < 12.7 V:the alternator charging current in regard to its
characteri stics must be checked.
IN TENSITY (A) EN GINEE7J
Rated intensity 75 80
Minimal intensity, which has to be supplied by the
altern ator to all working consumers 51 60
If the measured output is too little, the following will be checks:
-wear of alternator (collector brushes, etc.);
-battery connections;
-the mass braid of the engine;
-conformity of alternator;
-tension of carryi ng belt.
If the measured output is correct and the regulated voltage is too little, the cause may be:
-the car has too many electric consumers;
-the battery is flat. AL
TERNATOR
vnx.su

16E7J-A-2/60 ENGINE
16 - 4
ST ARTING AND CHARGING
SPECIAL DEVICES
MOT 1505BELT TENSION MEASURIN G DEVICE
DIS M O UNT ING
The car is set on a two-column lifting stand;
Disconnect the electric connections from the battery.
The fuel supply conduit is uncoupled;
The following are taken off: - air filter;
- the oil-gauge tube;
- the top scre w of the alternator;
- the alterna tor belt;
- the stretching fl ange of the alternator.
The car is suspended.
The electric connectors of the alternator are uncoupled;
Di smount the alternator l ower attachment screw.
Lower the vehicle.
The alterna tor is taken out at the top.
AL TERNATOR
R
E-MOUNTING
The mounting opera tions are done in the reverse orde r;
The carrying belt of t he alternator is stretched to get the re commended ( 263
Hz+/- 10% ) mounting voltage;
vnx.su

E7J-A-2/60 ENGINE16
16 - 5
ST ARTING AND CHARGING
The position of the alternator i s blocked.
The engine is revolved thre e and a half cra nkshaft turns;
The reading end of t he MOT. 1505 measuring device is placed in the measuring area;
The tension in the belt is measured;
It is checked whether t his fits i nto the mounting tension tolerance; if not, the belt will
be stretched again until the recommended tension ( 263 Hz +/- 10%) is reached.
The inspection a nd t he a djustment of the belt a re done with t he e ngine at ambient
temperature . Tighten at the require d moment, the alternator a ttachment screws :
- screw M10(lower attachment)-5 daNm
-screwM10 (upper attachment)-2.2 daNm.
Remark: Once dismounted, a belt is not to be remounted, but replaced.
MOT. 1505
MOT. 1505
AL
TERNATOR
vnx.su

16E7J-A-2/60 ENGINE
16 - 6
ST ARTING AND CHARGING
DIS M O UNT ING
(in the air -conditioning variant)
The car is placed on a two-column lifting stand;
The electric connections are uncoupled from the battery;
The following are taken apart: -the top scre w of the alternator;
-the belt of the alternator;
The right-side front wheel of the car is taken apart;
The car is suspended;
The two screws fixing the shock-absorber on the steeri ng swivel stand are taken off;
The steeri ng swivel stand is lowered and the right-side planetary tra nsmission is taken
off the planetary pi nion of the gearbox; The electric conductors of the alternator a re disconnected;
The screw of the alternator is taken off;
The alterna tor is taken apart laterally past the right-side planetary tra nsmission.
R
E-MOUNT ING
The taking-apart opera tions are done in the reverse order;
The carrying belt of the alternator is stretched to obtain the mounting tension recom-
mended (263 Hz +/- 10% );
The position of the alternator i s blocked;
The engine is revolved thre e and a half cra nkshaft turns;
The reading end of the MOT. 1505 measuring device is placed in the measuring area;
The tension in the belt is measured;
It is checked whether t his fits into the mounting tension tolera nce; if not , the belt will be
str etched again until the re commended tension ( 263 Hz +/- 10%) is reached.
The i nspection and the adjustment of the belt are done with the engine at ambient
temperature .
Tighten at the require d moment, the alternator a ttachment screws :- screw M10 (lower attachment)-5 daNm
-screw M10 (upper attachment)-2.2 daNm.
Remark: Once dismounted, a belt is not to be remounted, but replaced.
AL TERNATOR
vnx.su

19 - 12
19
COOLING - EX HA U ST - FU EL TANK
DISMOUNTING
The car is set on a two-column lifting stand.
The ba ttery is disconnected.
Th e co oling circuit is emptied at the filling stopper placed at the lower part of the radiator.
The fo llowing are taken apart.
- the distribution belt (see Chapter “ Distribution belt”) ;
- the ex tending pulley / runner (1);
- the fixing screws of the water-pump.
The water-pump is taken out at the upper end of the engine compartment.
SPECIAL DEVICES
MOT. 1202-02 Pincers for elastic collars
MOT. 1505 Device for measuring the belt tension
TIGHTENING COUPLES (daNm)
Screw-nut for extending pulley / runner 5
Screw for the crankshaft pulley 2+68
o+/-6o
Screws for right-side pendular stand 6.2
Screw-nut for hydro-elastic buffer 4.4
Screws for water-pump 2.2
Screw-nuts for water-pump 1
Screws for wheels 7.5
WATER PUMP
vnx.su