battery replacement DACIA SUPERNOVA 2004 Owner's Manual

82A
HORN - ENGINE IMMOBILISER
82A - 18
If the states
remain unchanged, check the following:
- electric connections of the decoding bushing
- the electric connections between the E.C.U. decoder and the decoding bushing
- the tension of the battery must have more than 8V when the starter is activated.
If all these are conformable, proceed to the replacement of the decoding bushing, and then
check again the a .m. states.
II. SOLVING MODE
When an electric ke y head (or both) is damaged, order (Info TECH LINE 0248/213766) a
new set of two electronic heads, subject to the vehicle type, as follows: TRF key head set – item no. 6001 543 684, 1 set, for DSN equipped with
anti intrusion (CLIMA or RAPSODIE)
TR-TRF key head set – item no. 6001 544 452, 1 set, for DSN without anti
intrusion (CLIMA or RAPSODIE)
TR key head set – item no. 6001 543 683, 1 set, for DSN EUROPA
Send to Tech Line (0248 213766), the chassis series no, the anti starting code of the damaged
key heads, the a nti starting code of the ne w key heads, and they will sent at their turn, to the
service center, the repairing code (taking into account that this code has a special regime). Additionally , there are necessary the new key heads, the E.C.U. decoder (obligatory TRF, if
the vehicle is equipped with central locking), the repairing code of the computer; proceed then to
the replacemen t of these items performing the following operation:
A) Replacement- c hecking electronic key heads :
Replace t he damaged key heads with the new ones (the metal insertions remain the same),
then by means of the CLIP tester, selecting COMPUTER TEST- ANTI STARTING- STATE
LIST, check following states with both keys:
If the states are in the following configuration, when setting the contact on, consecutively with
both keys:
ANTI STARTING……………………………………………..........ACTIVE
RECEIVED KEY CODE………………………………………….. ACTIVE
ACCEPTED KEY CODE…………………………………………PASSIVE DIAGNOSTIC
vnx.su

83
INSTRUMENT PANEL
DISMOUNTING
Disconnecting battery.
Dismounting flexible shaft( speedometer cable) from the gearbox.
Dismounting control cable from the recyclin g flap.
Dismounting steering wheel and the steering wheel casing.
Dismountin g dashboard lower fairing.
Dismountin g documents compartment.
Disconnect documents compartment lamp.
Dismountin g central console.
Dismounting flaps control cables from the climate control unit.
Discon necting: cigarette lighter, climate control lighting, ashtray lighting, climate control switch .
Dismounting headlamps adjustment control from the dashboard.
Dismounting dashboard from the windscreen lower cross bar.
Disconnecting flexible shaft (speedometer cable) from the instrument panel.
Disconnecting air conducting ducts to aerators.
Disconnecting front wiring from the instrument panel and from the dashboard wiring.
Dismounting instrument panel attachmen t clamps from the dashboard.
Dismountin g clamps from the instrument panel.
Mounting clamps on the new instrument panel.
Mounting instrument panel with clamps on dashboard.
Connecting flexible shaft to the instrument panel.
Connecting front wiring to the instrument panel and to the dashboard wiring.
Positioning and fixing air conducting ducts.
IN
STRUMENT PANEL REPLACEMENT
83-5
vnx.su

83
INSTRUMENT PANEL
Positioning and fixing flaps control cables to the climate control unit.
Connecting dashboard wirin g to: cigarette lighter, climate contro l lighting, climate control switch,
ashtray lighting.
Connecting documents compartment lamp.
Mounting documents compartment.
Mounting central console.
Mounting dashboard lower fairing.
Mounting steering wheel casing and steering wheel.
Mounting flexible shaft to the gearbox.
Mounting control cable to the recycling flap.
Connecting battery.
Functional tests.
REMOUNTING
Perform the dismounting operations in the reverse order.
83-6
IN
STRUMENT PANEL REPLACEMENT
vnx.su

83
INSTRUMENT PANEL
83-10
FUEL LEVEL TRANSMITTER REPLACEMENT
DISMOUNTING
Disconnect the battery.
Dismount the fuel tank-visiting cap, by acting upon the attachment screws.
Disconnect the transmitter connector from the rear wiring / fuel tank cap.
D etach the clips of the hoses connected to the fuel tank cap.
Rotate the probe attachment flange from right to left, by about 1/3 rotation, until it is released
from the attachment shoulders.
Pull out the assembly fuel tank cap-fuel pump-level transmitter;
Dismount the attachment screws of the fuel level transmitter.
REMOUNTING
Perform in the reverse order the dismounting operations, checking carefully the condition of
the tank cap-sealing gasket.
ELECTRIC TESTS – FUEL LEVEL TRANSMITTER
PO SITION OF THE FUEL LEVEL R
INDICATOR ON INSTRUMENT PANEL transmitter
(W)
4/4 7+/-15 %
3/4 50+/- 5 %
1/2 97+/- 5 %
1/4 162+/- 3 %
0 280+/- 3 %
minimal level warning -
FUEL LEVEL TRANSMITTER
vnx.su

84
CONTROLS - SIGNALLING
84-2
CONNECTING PLUGS REPLACEMENT
The operations are to be performed after dismounting the contact switch from the vehicle.
Di smount t he a ttachment screws of the
blocking wedge guiding.
Dismount the connecting plugs.
Position and mount the connecting plugs.
Mount the blocking wedge guiding
Tighten the attachment screws of the blocking wedge guiding.
DISMOUNTING-REMOUNTING THE FIX AND MOBILEHATCHBACK CONTACT (until 01.06.2001)
FIX CONTACT
DISMOUNTING
Disconnect the battery.
Di sconnect the connections boxes from
the rear wiring. Dismount the attachment screw(2) of the
guiding body.
MOBILE CONTACT
DISMOUNTING
Dismount the contact attachment screw (1) on the hatchback.
Dismount the attachment screws of the obturator cap on the hatchback.
Disconnect the mobile contact connectors from the consumers (license plate lamps, STOP-
S3 lamp, rear window defrosting). Extract the mobile contact and its wiring.
REMOUNTING
Perform the dismounting operations in the reverse order, previously checking the contacts
base pins sliding. DISMOUNTING
REMOUNTING
Extract by detaching from clips the fix contact from the guiding body.
REMOUNTING
Perform the dismounting
operations in the reverse order. ANTI THEFT MECHANISM
vnx.su