ABS DAEWOO LACETTI 2004 Service Repair Manual

4E1 – 6IREAR DISC BRAKES
DAEWOO V–121 BL4
2. Apply a few drops of thread–locking compound to
the caliper bracket mounting bolts and install the
caliper bracket.
Tighten
Tighten the caliper bracket mounting bolts to 56 NSm
(41 lb–ft).
3. Install the brake shoes and the caliper. See ”Cali-
per” in this section.
HUB AND PARKING BRAKE
SHOE/BACKPLATE
Removal Procedure
1. Remove the caliper mounting bracket.
2. Remove the rotor detent screw.
3. Remove the rotor.
4. Remove the rear ABS sensor connector.

REAR DISC BRAKES 4E1 – 9
DAEWOO V–121 BL4
5. Connect the ABS sensor connector.
6. Install the rotor with detent screw.
Tighten
Tighten the rotor detent screw to 4 NSm (35 lb–in).
7. Install the caliper mounting bracket with bolts.
Tighten
Tighten the caliper bracket mounting bolts to 56 NSm
(41 lb–ft).
8. Install the wheel.

4E2 – 8IREAR DRUM BRAKES
DAEWOO V–121 BL4
Installation Procedure
1. Install the wheel cylinder to the backing plate with
the wheel cylinder bolt.
Tighten
Tighten the wheel cylinder–to–backing plate bolt to 8
NSm (71 lb–in).
2. Connect the brake line to the wheel cylinder.
Tighten
Tighten the brake line to 16 NSm (12 lb–ft)
3. Install the shoe and lining, and the brake drum. Re-
fer to ”Shoe and Lining” in this section.
4. Bleed the brakes. Refer to Section 4A, Hydraulic
Brakes.
BACKING PLATE
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the brake shoe components, including
complete removal of the parking brake with the re-
tainer. Refer to ”Shoe and Lining” in this section
and Section 4A, Hydraulic Brakes.
3. Remove the nuts that secure the wheel hub assem-
bly to the backing plate.
4. Remove the brake line and plug the opening in the
line to prevent fluid loss or contamination.
5. Remove the wheel cylinder assembly. Refer to
”Wheel Cylinder Assembly” in this section.
6. Remove the wheel hub assembly.
7. In case of ABS brake, disconnect the cable that
goes to the wheel speed sensor.
8. Separate the backing plate and the gasket.

SECTION : 4F
ANTILOCK BRAKE SYSTEM
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS4F–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 4F–2. . . . . . . . . .
SPECIAL TOOLS4F–2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 4F–2. . . . . . . . . . . . . . . . . . . . . . . .
SCHEMATIC AND ROUTING DIAGRAMS4F–3 . . . . .
Abs System Circuit (I) 4F–3. . . . . . . . . . . . . . . . . . . . . .
Abs System Circuit (II) 4F–4. . . . . . . . . . . . . . . . . . . . .
Ebcm Connector Face View 4F–5. . . . . . . . . . . . . . . . .
COMPONENT LOCATOR4F–6 . . . . . . . . . . . . . . . . . . . .
ABS/EBD System Drive 4F–6. . . . . . . . . . . . . . . . . . . .
DIAGNOSIS4F–7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Circuit Check 4F–7. . . . . . . . . . . . . . . . . . .
ABS Indicator Lamp Inoperative 4F–9. . . . . . . . . . . . .
Power Supply to Control Module,
No DTCs Stored 4F–12. . . . . . . . . . . . . . . . . . . . . . . .
ABS Indicator Lamp Illuminated Continuously,
No DTCs Stored 4F–16. . . . . . . . . . . . . . . . . . . . . . . .
Electronic Brake–Force Distribution (EBD)
System Indicator Lamp Inoperative 4F–18. . . . . . . .
SELF–DIAGNOSTICS 4F–22. . . . . . . . . . . . . . . . . . . .
DISPLAYING DTCs 4F–22. . . . . . . . . . . . . . . . . . . . . . .
CLEARING DTCs 4F–22. . . . . . . . . . . . . . . . . . . . . . . .
INTERMITTENTS AND POOR
CONNECTIONS 4F–22. . . . . . . . . . . . . . . . . . . . . . . .
DTC C0035 Left Front Wheel Speed Sensor
Circuit Malfunction 4F–23. . . . . . . . . . . . . . . . . . . . . .
DTC C0040 Right Front Wheel Speed Sensor
Circuit Malfunction 4F–26. . . . . . . . . . . . . . . . . . . . . .
DTC C0045 Left Rear Wheel Speed Sensor
Circuit Malfunction 4F–29. . . . . . . . . . . . . . . . . . . . . .
DTC C0050 Right Rear Wheel Speed Sensor
Circuit Malfunction 4F–32. . . . . . . . . . . . . . . . . . . . . .
DTC C0060/C0065 Left Front Inlet and
Outlet Valve Solenoid Fault 4F–35. . . . . . . . . . . . . . .
DTC C0070/C0075 Right Front Inlet and
Outlet Valve Solenoid Fault 4F–37. . . . . . . . . . . . . . . DTC C0080/C0085 Left Rear Inlet and
Outlet Valve Solenoid Fault 4F–39. . . . . . . . . . . . . . .
DTC C0090/C0095 Right Rear Inlet and
Outlet Valve Solenoid Fault 4F–41. . . . . . . . . . . . . . .
DTC C0110 Pump Motor Circuit Malfunction 4F–43. .
DTC C0121 Valve Relay Circuit Malfunction 4F–45. .
DTC C0161 ABS Brake Switch Circuit
Malfunction 4F–47. . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC C0245 Wheel Speed Sensor Frequency
Error 4F–50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC C0550 ABS Control Module Internal
Fault 4F–54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC C0800 Low Voltage Fault 4F–56. . . . . . . . . . . . .
DTC C0931 Overheated 4F–59. . . . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR4F–60 . . . . . . . . . . . . . .
ON–VEHICLE SERVICE 4F–60. . . . . . . . . . . . . . . . . . . .
Service Precautions 4F–60. . . . . . . . . . . . . . . . . . . . . . .
Bleeding System 4F–61. . . . . . . . . . . . . . . . . . . . . . . . .
ABS 5.3 Assembly 4F–61. . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 4F–62. . . . . . . . . . . . . . . .
Front Wheel Speed Sensor Jumper Harness 4F–63.
Rear Wheel Speed Sensor 4F–64. . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION4F–65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Knowledge Required 4F–65. . . . . . . . . . . . . . . . .
ABS System Components 4F–65. . . . . . . . . . . . . . . . .
Base Braking Mode 4F–65. . . . . . . . . . . . . . . . . . . . . . .
Antilock Braking Mode 4F–66. . . . . . . . . . . . . . . . . . . . .
EBD System 4F–69. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Brake–Force Distribution (EBD) Failure
Matrix 4F–70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tires and ABS/EBD 4F–71. . . . . . . . . . . . . . . . . . . . . . .
Electronic Brake Control Module (EBCM) 4F–71. . . .
Front Wheel Speed Sensors 4F–71. . . . . . . . . . . . . . .
Front Wheel Speed Sensor Rings 4F–71. . . . . . . . . . .
Rear Wheel Speed Sensors and Rings 4F–71. . . . . .
Valve Relay and Pump Motor Relay 4F–71. . . . . . . . .

4F – 2IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
Wiring Harness 4F–71. . . . . . . . . . . . . . . . . . . . . . . . . . . Indicators 4F–71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
ABS 5.3 Mounting Nuts1511–
Brake Pipe Nuts2216–
Front Wheel Speed Sensor Bolt8–71
SPECIAL TOOLS
SPECIAL TOOLS TABLE
Scan Tool

ANTILOCK BRAKE SYSTEM 4F – 3
DAEWOO V–121 BL4
SCHEMATIC AND ROUTING DIAGRAMS
ABS SYSTEM CIRCUIT (I)
1
12
2
C111 1 2 2
E B C M
19
16 1418
B+
B+1576 54
G106
10A
62C202 BRN
BRN
BRN
BRN
BRNF11
Hot in Run and Start
6C110 C107 C107
40 C202
60A
1
6C105
C102
RED ORN/
BLK
RED RED
RED
Ground IGN+
Ground LT B L U Brake
Switch2
4Ef215AEf13
Hot at All Times
4330
C201 C201
J3B14F01
11
11
S301
2 WHT GRYGRY
WHT GRY
WHT PPL
YEL
WHTWHT
RED
BRN BRN
BLK BLK
DK
BLUBRN LT
BLU
1
21 4 5
10 89 3
31
C110
43
12
C30214C202
LT B L U LT B L U LT B L U
LT B L U
RR/LH
Wheel Speed SensorRR/RH BLK/WHT
G106
BLK
61
C201
76
C201
17
Oil feeding
Connector
”2”Ter
Oil feeding
Connector
”4”Ter
FRT/LHWheel Speed Sensor
FRT/RH
1C110

4F – 4IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
ABS SYSTEM CIRCUIT (II)
60A
REDEf2
2
C107
J3B14F02
Oil feeding
Connector
BLK/WHT
G106
10A30
F4
32 43
A19
A13 A14
S301A1 C201 C201
31C201 C201 C201
C202
C110
C110
C101
C106C202 WHT
BRN BRN BRN
DLC
(Data Link
Connector) LT GRN
DK
GRN
DK
GRN LT GRN/
BLK
LT GRN/
BLK
LT GRN
LT GRN LT GRN
LT GRN LT GRN
DK BLU
DK BLUDK BLUDK BLU
DK BLU
DK BLU
ECM
”53” Ter.
(Sirius D4)ECM
”K7” Ter.
(MR–140)PPL/
WHT
PPL/
WHT
WHT/
YELPPL/WHTPPL/WHT
PPL/WHT PPL/WHT ABS
Warning
LampTCS
Warning
LampParking
Brake
Warning
Lamp
Hot in Run and Start
Hot at all times
PNK
Cluster I/P
Fuse
Block
PNK
EBCMBrake Fluid
Switch
”1” Ter.
Parking Brake
Switch 8
88 9
92 20 2222 16
41
3
42
1
11
12
19
12 432
1
21
25 23 11
6C110
C202
10A30
F11
62B15
15 15

ANTILOCK BRAKE SYSTEM 4F – 5
DAEWOO V–121 BL4
EBCM CONNECTOR FACE VIEW
EBCM Connector
PinColorCircuit
1WHTRight Rear Ground
2BRNRight Rear Sensor
3PPLRight Front Ground
4–Not Used
5YELRight Front Sensor
6WHTLeft Front Ground
7ORNLeft Front Sensor
8REDLeft Rear Ground
9BLKLeft Rear Sensor
10–Not Used
11DK BLU/
WHTData Link Connector
(DLC)
12–Not Used
13–Not Used
14YELBrake Lamp Switch
15PNKSwitched Ignition
16BLKMotor Ground
PinColorCircuit
17REDBattery
18REDBattery
19BLK/WHTInstrument Ground
20LT GRNABS Warning Lamp
21BRN/WHTEBD Warning Lamp
(Parking Brake Lamp)
22–Not Used
23–Not Used
24–Not Used
25–WSS Output Signal
26–Not Used
27–Not Used
28–Not Used
29–Not Used
30–Not Used
31–Not Used
SB–Shorting Bar

4F – 6IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
COMPONENT LOCATOR
ABS/EBD SYSTEM DRIVE
(Left–Hand Drive Shown, Right–Hand Drive Similar)
1. Right Front Wheel Speed Sensor
2. Brake Master Cylinder
3. Master Cylinder Reservoir
4. Grommet
5. Right Front Wheel Speed Sensor Connector
6. Brake Fluid Level Switch Connector
7. Instrument Cluster
8. Connector C302
9. Right Rear Wheel Speed Sensor Connector
10. Right Rear Wheel Speed Sensor
11. Left Rear Wheel Speed Sensor12. Left Rear Wheel Speed Sensor Connector
13. Body Wiring Harness
14. Connector C202
15. Connectors C110
16. EBCM Connector
17. Left Front Speed Sensor Connector
18. Grommet
19. Hydraulic Modulator with Attached EBCM
20. Connector C107
21. Left Front Wheel Speed Sensor

ANTILOCK BRAKE SYSTEM 4F – 7
DAEWOO V–121 BL4
DIAGNOSIS
J3B14F04
60A Ef230A Ef5
2
42
C107 C105
2
C110
G106
A19
A13 A1 A14
C110 C202
C202WHT LT GRN
DK
GRN LT GRN/
BLK
BLK
DK BLUDK BLU
PPL/WHT
PPL/WHT ABS
TCS Parking
Brake
Hot at all times
RED REDRED/WHT
Ignition
Switch
RED
RED
I/P Cluster
EBCM8
20
22 2216 41
1211
18 1621
1
C107
10A F410AF11
32 31
43
6 62 C201
C201 C201C201
C110 C202
Hot in Run and Start
30
4
1711
C202
15
B15
DLC
(Data Link
Connector)12
G106
BLK/WHTOil Feeding
Connector
”2” Ter.
BRNBRN BRN
BRN PNK PNK PNK
19J1
59B1
ONStart Lock
Acc
IG1
19
DIAGNOSTIC CIRCUIT CHECK
The Diagnostic Circuit Check is an organized approach to
identifying a problem created by an antilock brake system
(ABS) malfunction. It must be the starting point for any
ABS complaint diagnosis because it directs the service
technician to the next logical step in diagnosing the com-
plaint.
Diagnostic Process
Perform the following steps in order when servicing the
ABS/EBD system. Failure to do so may result in the loss
of important diagnostic data and may lead to difficulties
and time–consuming diagnosis procedures.1. Perform the tests of the table below.
2. Perform a road test if directed by the table.
S Test drive the vehicle while using the snapshot
feature of the scan tool.
S Perform normal acceleration, stopping, and turn-
ing maneuvers.
S If this does not reproduce the malfunction, per-
form an ABS stop on a low friction surface such
as gravel.
3. Clear the diagnostic trouble codes (DTCs) after all
system malfunctions have been corrected.
Diagnostic Circuit Check
StepActionValue(s)YesNo
11. Install the scan tool.
2. Turn ignition switch to ON.
3. Select the Data List mode.
Is the scan tool receiving data from the electronic
brake control module (EBCM) ?–Go to Step 2Go to Step 6
2Check the display.
Are there any current DTCs displayed?–Refer to the ap-
plicable DTC
tableGo to Step 3