clutch DAEWOO LACETTI 2004 Service User Guide

ENGINE CONTROLS 1F – 9
DAEWOO V–121 BL4
Spark Advance
This is a display of the spark advance Ignition Coil (IC) cal-
culation which the ECM is programming in the ignition sys-
tem. It computes the desired spark advance using data
such as engine temperature, rpm, engine load, vehicle
speed and operating mode.
TCC Engaged
When the brake pedal is applied, the Torque Converter
Clutch (TCC) brake switch sends a signal to the ECM to
disengage the TCC and disable the cruise control.
Total Misfire Current Counter
Indicates the total number of misfires that have been de-tected in all the cylinders after 100 engine cycles. One
cycle equals one complete 4 stroke cycle. The total misfire
only increments during the steady state cruise conditions.
TP Sensor
The ECM uses the TP Sensor in order to determine the
amount of the throttle demanded by the vehicle’s operator.
The TP Sensor reads between 0.36–0.96 volts at idle to
above 4 volts at WOT.
Vehicle Speed
The vehicle speed sensor signal is converted into mph or
km/h for display. The vehicle speed output from the ECM
is 4000 pulses per mile. The scan tool uses the KWP 2000
serial data from the ECM to obtain vehicle speed, while the
Instrument Panel Cluster (IPC), cruise control module and
the chime alarm module use the 4000 ppm output.

1F – 94IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
31. Check the engine fuse block fuse Ef6 and Ef8.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the data link connector
(DLC).
4. The cooling fans should run at low speed when
the coolant temperature reaches 97°C
(207°F).
Do the cooling fans run at low speed?–Go to Step 5Go to Step 10
51. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the DLC.
4. Start the engine.
5. The cooling fans should run at high speed
when the coolant temperature reaches 101°C
(214°F).
Do the cooling fans run at high speed?–Go to Step 6Go to Step 33
61. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8Go to Step 7
71. Diagnose the A/C compressor clutch circuit.
2. Repair the A/C compressor clutch circuit as
needed.
3. Start the engine.
4. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8–
8Do the cooling fans run at low speed?–Go to Step 9Go to Step 31
91. Turn the ignition OFF.
2. Connect the A/C pressure gauges.
3. Start the engine.
4. Turn the A/C switch ON.
5. The cooling fans should run at high speed
when the high side A/C pressure reaches 1
882 kPa (273 psi).
Do the cooling fans run at high speed?–Go to Step 10–
101. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Turn the ignition ON.
6. Connect a test light between the main cooling
fan connector terminal 2 and ground.
Is the test light on?–Go to Step 11Go to Step 12

ENGINE CONTROLS 1F – 101
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
31. Check the engine fuse block fuse Ef21, Ef6,
Ef8.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the data link connector
(DLC).
4. The cooling fans should run at low speed when
the coolant temperature reaches 97°C
(207°F).
Do the cooling fans run at low speed?–Go to Step 5Go to Step 10
51. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the DLC.
4. Start the engine.
5. The cooling fans should run at high speed
when the coolant temperature reaches 101°C
(214°F).
Do the cooling fans run at high speed?–Go to Step 6Go to Step 33
61. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8Go to Step 7
71. Diagnose the A/C compressor clutch circuit.
2. Repair the A/C compressor clutch circuit as
needed.
3. Start the engine.
4. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8–
8Do the cooling fans run at low speed?–Go to Step 9Go to Step 31
91. Turn the ignition OFF.
2. Connect the A/C pressure gauges.
3. Start the engine.
4. Turn the A/C switch ON.
5. The cooling fans should run at high speed
when the high side A/C pressure reaches 1
882 kPa (273 psi).
Do the cooling fans run at high speed?–Go to Step 10–
101. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Turn the ignition ON.
6. Connect a test light between the main cooling
fan connector terminal 2 and ground.
Is the test light on?–Go to Step 11Go to Step 12

ENGINE CONTROLS 1F – 125
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0117
ENGINE COOLANT TEMPERATURE SENSOR LOW
VOLTAGE
Circuit Description
The Engine Coolant Temperature sensor (ECT) uses a
thermistor to control the signal voltage to the engine con-
trol module (ECM).
The ECM supplies a voltage on the signal circuit to the
sensor. When the engine coolant is cold, the resistance is
high; therefore the ECT signal voltage will be high.
As the engine warms, the sensor resistance becomes
less, and the voltage drops. At normal engine operating
temperature, the voltage will be between 1.5 and 2.0 volts
at the ECT signal terminal.
The ECT sensor is used to the following items:
S Fuel delivery.
S Lock Up Clutch (LUC).
S Ignition.
S Evaporative Emission (EVAP) Canister Purge
Valve.
S Electric cooling fan.
Conditions for Setting the DTC
S ECT voltage is less than 0.03V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The coolant fan turns ON.
S The ECM will default to 20°C (68°F) for the first 60
seconds of the engine run time, and then 92 °C
(198 °F).
S The scan tool will not show the defaulted value.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
After the engine has started, the ECT should rise steadily
to about 90°C (194°F) then stabilize when the thermostat
opens.
Use the temperature vs. Resistance values table to evalu-
ate the possibility of a skewed sensor. Refer to ”Tempera-
ture vs. Resistance” in this section.

1F – 128IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0118
ENGINE COOLANT TEMPERATURE SENSOR HIGH
VOLTAGE
Circuit Description
The coolant temperature sensor (ECT) uses a thermistor
to control the signal voltage to the engine control module
(ECM).
he ECM supplies a voltage on the signal circuit to the sen-
sor. When the air is cold, the resistance is high; therefore
the ECT sensor signal voltage will be high.
As the engine warms, the sensor resistance becomes
less, and the voltage drops. At normal engine operating
temperature, the voltage will be between 1.5 and 2.0 volts
at the ECT sensor signal terminal.
The ECT sensor is used to the following items:
S Fuel delivery.
S Lock Up Clutch (LUC).
S Ignition.
S Evaporative Emission (EVAP) Canister Purge
Valve.
S Electric cooling fan.
Conditions for Setting the DTC
S ECT voltage is greater than 4.98V.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The coolant fan turns ON.
S The ECM will substitutes a fixed MAP value and
use TP to control the fuel delivery (the scan tool will
not show defaulted)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
After the engine has started, the ECT should rise steadily
to about 90°C (194°F) then stabilize when the thermostat
opens.
Use the temperature vs. Resistance values table to evalu-
ate the possibility of a skewed sensor. Refer to ”Tempera-
ture vs. Resistance” in this section.

1F – 264IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0532
A/C PRESSURE SENSOR LOW VOLTAGE
Circuit Description
The Air Conditioning (A/C) system uses an A/C refrigerant
pressure sensor mounted in the high pressure side of the
A/C refrigerant system to monitor A/C refrigerant pres-
sure. The Engine Control Module (ECM) uses this infor-
mation to turn ON the engine coolant fans when the A/C
refrigerant pressure is high and to keep the compressor
disengaged when A/C refrigerant pressure is excessively
high or low.
The Air Conditioning Pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will cause the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is outside
of the possible range of the sensor. When the signal is out
of range for a prolonged period of time, the ECM will not
allow the A/C compressor clutch to engage. This is done
to protect the compressor.
Conditions for Setting the DTC
S A/C pressure is less than 12.16 kpa.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffers.S A history DTC is stored.
S The A/C compressor operation will be disabled
while the low voltage indication exists.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the A/C Pressure sensor. A change in
the A/C pressure display will indicate the location of the
fault.
If DTC P0532 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

ENGINE CONTROLS 1F – 267
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0533
A/C PRESSURE SENSOR HIGH VOLTAGE
Circuit Description
The Air Conditioning (A/C) system uses an A/C refrigerant
pressure sensor mounted in the high pressure side of the
A/C refrigerant system to monitor A/C refrigerant pres-
sure. The Engine Control Module (ECM) uses this infor-
mation to turn ON the engine coolant fans when the A/C
refrigerant pressure is high and to keep the compressor
disengaged when A/C refrigerant pressure is excessively
high or low.
The Air Conditioning Pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will cause the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is outside
of the possible range of the sensor. When the signal is out
of range for a prolonged period of time, the ECM will not
allow the A/C compressor clutch to engage. This is done
to protect the compressor.
Conditions for Setting the DTC
S A/C pressure is greater than 293 kpa.
S Engine is running.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffers.
S A history DTC is stored.
S The A/C compressor operation will be disabled
while the high voltage indication exists.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P0533 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

1F – 324IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1537
A/C COMPRESSOR RELAY HIGH VOLTAGE
Circuit Description
The A/C system uses an A/C refrigerant pressure sensor
mounted in the high pressure side of the A/C refrigerant
system to monitor A/C refrigerant pressure. The engine
control module (ECM) uses this information to turn ON the
engine coolant fans when the A/C refrigerant pressure is
high and to keep the compressor disengaged when A/C
refrigerant pressure is excessively high or low.
The air conditioning pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will causes the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is out of
the possible range of the sensor. When the signal is out of
range for a prolonged period of time, the ECM will not allow
the A/C compressor clutch to engage. This is done to pro-
tect the compressor.
Conditions for Setting the DTC
S The air conditioning compressor relay circuit is a
short to battery condition exists.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.

1F – 326IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1538
A/C COMPRESSOR RELAY LOW VOLTAGE
Circuit Description
The A/C system uses an A/C refrigerant pressure sensor
mounted in the high pressure side of the A/C refrigerant
system to monitor A/C refrigerant pressure. The engine
control module (ECM) uses this information to turn ON the
engine coolant fans when the A/C refrigerant pressure is
high and to keep the compressor disengaged when A/C
refrigerant pressure is excessively high or low.
The air conditioning pressure (ACP) sensor operates like
other 3–wire sensors. The ECM applies a 5.0 volt refer-
ence and a sensor ground to the sensor. Changes in the
A/C refrigerant pressure will causes the ACP sensor input
to the ECM to vary. The ECM monitors the ACP sensor
signal circuit and can determine when the signal is out of
the possible range of the sensor. When the signal is out of
range for a prolonged period of time, the ECM will not allow
the A/C compressor clutch to engage. This is done to pro-
tect the compressor.
Conditions for Setting the DTC
S The air conditioning compressor relay circuit is a
short to ground an open condition exists.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.

ENGINE CONTROLS 1F – 347
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0106
MANIFOLD ABSOLUTE PRESSURE RATIONALITY
Circuit Description
The Engine Control Module (ECM) uses the Manifold Ab-
solute Pressure (MAP) sensor to control the fuel delivery
and the ignition timing. The MAP sensor measures the
changes in the intake manifold pressure which results
from engine load (intake manifold vacuum) and the rpm
changes, and it converts these into voltage outputs. The
ECM can detect if the MAP sensor is not responding to the
Throttle Position (TP) changes by comparing the actual
MAP change to a predicted MAP change based on the
amount of TP change that occurs. If the ECM does not see
the expected MAP change or more, DTC P0106 will set.
Conditions for Setting the DTC
S Altitude compensated MAP reading is higher than
high threshold or lower than low threshold table
based on rpm and TP signal.
S DTCs P0107, P0108, P0117, P0118, P0122,
P0123, P0201, P0202, P0203, P0204, P0300,
P0351, P0352, P0402, P0404, P1404, P0405,
P0406, P0506, P0507 are not set.
S Engine running.
S Valid Barometric Pressure (BARO) update.
S Torque Converter Clutch (TCC) steady (A/T).
S A/C steady state.
S No TP sensor fail conditions present.
S No MAP fail conditions present.
S Change in Idle Air Control (IAC) is less than 5%.
S Coolant temperature is greater than –10°C (14°F).
S Change in rpm is less than 200.
S Change in TP sensor is less than 3%.
S Change in Exhaust Gas Recirculation (EGR) value
is less than 6%.
S The rpm is between 1300 and 4500.
S All of the above are stabilized for 1.5 seconds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The ECM will substitute a fixed MAP value and use
TP sensor to control the fuel delivery. (The scan
tool will not show defaulted value.)
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.Diagnostic Aids
With the ignition ON and the engine stopped, the manifold
pressure is equal to atmospheric pressure and the signal
voltage will be high. This information is used by the ECM
as an indication of vehicle altitude. Comparison of this
reading with a known good vehicle with the same sensor
is a good way to check the accuracy of a suspect sensor.
Readings should be the same +0.4 volt.
The MAP sensor vacuum source should be thoroughly
checked for restrictions at the intake manifold.
Test Description
Numbers below refer to the step numbers on the Diagnos-
tic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the occurred. The information is then stored on the
scan tool for later reference.
2. A sensor that displays an ignition ON, engine OFF
BARO value that does not appear normal for the
altitude the vehicle is in should be considered to be
malfunctioning.
3. While starting the engine, the MAP sensor should
detect any changes in the manifold pressure. This
test is to determine if the sensor is stuck at a value.
4. A normal MAP sensor will react as quickly to the
throttle changes as they can be made. A sensor
should not appear to be lazy or catch up with the
throttle movements.
5. This step checks if the reason for no MAP change
was due to a faulty sensor or vacuum source to the
sensor.
6. The MAP sensor vacuum source should be thor-
oughly checked for restrictions. A drill bit can be
used to clean out any casting flash that may exist in
the vacuum port.
7. The MAP sensor vacuum source should be thor-
oughly checked for restrictions. A drill bit can be
used to clean out any casting flash that may exist in
the vacuum port.
9. The MAP Sensor System Performance diagnostic
may have to complete several tests before deter-
mining if the diagnostic has passed or failed the last
test. Operate the vehicle in the Conditions for Set-
ting the DTC several times to ensure that the diag-
nostic runs enough tests to pass or fail.
10. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic
Aids”in this section for additional checks and infor-
mation.