Brake DAEWOO LACETTI 2004 Service Repair Manual

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 49
DAEWOO V–121 BL4
Functional Check Procedure
Inspect
1. Install a tachometer or scan tool.
2. Operate the vehicle unit proper operating tempera-
ture is reached.
3. Drive the vehicle at 80 to 88km/h (50 to 55 mph)
with light throttle(road load).
4. Maintaining throttle position, lightly touch the brake
pedal and check for release of the TCC and a slight
increase in engine speed(rpm).
5. Release the brake slowly accelerate and check for
a reapply of the Lock up clutch and a slight de-
crease in engine speed(rpm).
Torque Converter Evaluation
Torque Converter Stator
The torque converter stator roller clutch can have one of
two different type malfunctions :
A. Stator assembly freewheels in both directions.
B. Stator assembly remains Locked up at all times.
Condition A – Poor Acceleration Low
Speed
The car tends to have poor acceleration from a stand still.
At speeds above 50 to 55km/h(30 to 35mph), the car may
act normal. If poor acceleration is noted, it should first be
determined that the exhaust system is not blocked, and
the transaxle is in 1st(First) gear when starting out.
If the engine freely accelerates to high rpm in N(Neutral),
it can be assumed that the engine and exhaust system are
normal. Checking for poor performance in ”Drive” and ”Re-
verse” will help determine if the stator is freewheeling at all
times.
Condition B – Poor Acceleration High
Speed
Engine rpm and car speed limited or restricted at high
speeds. Performance when accelerating from a standstill
is normal. Engine may overheat. Visual examination of the
converter may reveal a blue color from overheating.
If the converter has been removed, the stator roller clutch
can be checked by inserting two fingers into the splined in-
ner race of the roller clutch and trying to turn freely clock-
wise, but not turn or be very difficult to turn counter clock-
wise.
Noise
Torque converter whine is usually noticed when the ve-
hicle is stopped and the transaxle is in ”Drive” or ”Re-
verse”. The noise will increase when engine rpm is in-
creased. The noise will stop when the vehicle is moving or
when the torque converter clutch is applied because both
halves of the converter are turning at the same speed.
Perform a stall test to make sure the noise is actually com-
ing from the converter :1. Place foot on brake.
2. Put gear selector in ”Drive”.
3. Depress accelerator to approximately 1200rpm for
no more than six seconds.
Notice : If the accelerator is depressed for more than six
seconds, damage to the transaxle may occur.
A torque converter noise will increase under this load.
Important : This noise should not be confused with pump
whine noise which is usually noticeable in P (Park), N
(Neutral) and all other gear ranges. Pump whine will vary
with pressure ranges.
The torque converter should be replaced under any of the
following conditions:
S External leaks in the hub weld area.
S Converter hub is scored or damaged.
S Converter pilot is broken, damaged or fits poorly
into crankshaft.
S Steel particles are found after flushing the cooler
and cooler lines.
S Pump is damaged or steel particles are found in the
converter.
S Vehicle has TCC shudder and/or no TCC apply.
Replace only after all hydraulic and electrical diag-
noses have been made.(Lock up clutch material
may be glazed.)
S Converter has an imbalance which cannot be cor–
rected. (Refer To Converter Vibration Test Proce-
dure.)
S Converter is contaminated with engine coolant con-
taining antifreeze.
S Internal failure of stator roller clutch.
S Excess end play.
S Heavy clutch debris due to overheating (blue con-
verter).
S Steel particles or clutch lining material found in fluid
filter or on magnet when no internal parts in unit are
worn or damaged(indicates that lining material
came from converter).
The torque converter should not be replace if :
S The oil has an odor, is discolored, and there is no
evidence of metal or clutch facing particles.
S The threads in one or more of the converter bolt
holes are damaged.
–correct with thread insert.
S Transaxle failure did not display evidence of dam-
age or worn internal parts, steel particles or clutch
plate lining material in unit and inside the fluid filter.
S Vehicle has been exposed to high mileage(only).
The exception may be where the Lock up clutch
damper plate lining has seen excess wear by ve-
hicles operated in heavy and/or constant traffic,
such as taxi, delivery or police use.
Lock–Up Clutch Shudder Diagnosis
The key to diagnosing lock–up clutch(TCC) shudder is to
note when it happens and under what conditions.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 57
DAEWOO V–121 BL4
Symptom ActionPossible Cause
Sealing Ring Selector ShaftS Check sealing ring.
S Replace sealing ring as described in the repair
instruction.
O–ring at Socket OutletS Check O–ring.
S Replace O–ring as described in the repair in-
struction.
O–ring and Speed Sensor ConnectionS Check O–ring.
S Replace O–ring as described in the repair in-
struction.
Oil Leak Incorrectly IdentifiedS No oil leak is possible at this point.
Speed Sensor Itself Is LeakingS Check speed sensor.
S Replace speed sensor as described in the re-
pair instruction.
Hair Line Crack at the Piping in the Con-
nection Area, Sealing Ring Fit in Trans-
axle HousingS Pressurize the line with compressed air and
check it.
S Replace lines as described in the repair in-
struction.
O–ring Defective, IncorrectCheck O–ring.
Replace O–rings as described in the repair instruc-
tion.
Plug LooseCheck the Tightening Torque for the screw plug.
Tighten to torque specified in the repair instruction.
Noise
SymptomPossible CauseAction
NoiseTFT Level Too LowS When the TFT level is too low, the gear wheels
from the transaxle oil pump might generate
noise.
S Check the TFT level as described in the repair
instruction and fill to the proper level.
Monolith in Catalytic Converter Has
BrokenS Check according to the exhaust gas diagnostic
procedure or by shaking the catalytic converter
casing.
S Replace catalytic converter if necessary.
Noise from Auxiliaries (e.g. exhaust
system, alternator, drive shafts.)S Check these components; if necessary, elimi-
nate the faults as described in the repair in-
struction
Noise from Tires or Wheel BearingsS Eliminate fault if necessary
Noise from Planetary GearsS Whistling noise on traction and overrun(in first
gear only)caused by high rotating speeds(func-
tionally unavoidable)
Cumulative Tooth Backlash in the Com-
plete Drive LineS Production status. Customer must be con-
vinced.
Jerky Noise of the Parking Lock (e.g.
when the car is standing on a gradient)S Load–reversal reaction
S Apply the handbrake before selection the park-
ing Lock (position P)

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 61
DAEWOO V–121 BL4
DTCDefault Action Indication Description
P0703Brake Switch Circuit
MalfunctionNo ChangeS TCM assume that the brake light always active.
S Open lock up clutch.
P0705Transmission Range Sen-
sor Circuit Malfunction
(PRNDL Input)MIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant 4th
gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic control,
position P, R and N also possible.
P0710S Transmission Fluid
Temperature Sensor
Circuit MalfunctionNo ChangeS TCM assume the transaxle fluid temperature is
140°F (60°C).
S No influence at vehicle running.
P0715S Input Speed Sensor
Circuit MalfunctionMIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/Substitute mode and constant 4th
gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic control,
position P, R and N also possible.
S Open lock up clutch.
P0716S Input Speed Sensor
Circuit Range/Perfor-
manceMIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant 4th
gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic control,
position P, R and N also possible.
S Open lock up clutch.
P0717S Input Speed Sensor
Circuit Range/Perfor-
manceMIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant 4th
gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic control,
position P, R and N also possible.
S Open lock up clutch.
P0720Output Speed Sensor Cir-
cuit MalfunctionMIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant 4th
gear.
S Open lock up clutch.
P0721Output Speed Sensor Cir-
cuit Range/PerformanceMIL ONS The TCM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant 4th
gear.
S Open lock up clutch.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 83
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P0703
BRAKE SWITCH CIRCUIT MALFUNCTION
Circuit Description
The brake switch is used to indicate brake pedal status to
the transaxle control module(TCM). The brake switch is a
normally open switch. Applying the brake pedal closes the
switch, supplying voltage to the TCM. Releasing the brake
pedal interrupts voltage to the TCM.
This DTC is stored at start–up. If the TCM receives a brake
switch signal after start–up, the DTC will be stored in
memory.
Conditions for Setting The DTC
S Brake switch stuck to closed.
S Brake switch wiring harness shortage to ground.
S Brake switch wiring harness shortage to power.S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S No lamp control required but diagnostic information
should be stored immediately when malfunction is
detected.
S TCM assume that the brake light always active.
Conditions For Clearing The MIL/DTC
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Inspect the poor wiring harness connection for TCM
connectors and transaxle wiring connectors.
S Inspect the improperly formed or damage terminals.

5A1 – 84IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DTC P0703 – Brake Switch Circuit Malfunction
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
21. Install the scan tool.
2. Turn the ignition ON. With the engine OFF.
3. Record then clear DTC(s)
4. Select scan tool stransmission data display.
5. Disconnect the brake switch connector.
6. Did the brake switch status change from” on” to
”off”?–Go to Step 3Go to Step 4
31. Replace the brake switch.
2. Refer to Brake Replacement.
3. After the ignition OFF, turn ignition ON.
Is the DTC reset?–Go to Step 4Go to Step 15
4Inspect the EF13.
Is the fuse blown?–Go to Step 5Go to Step 6
5Replace the fuse.
Is the action complete?–System OK–
61. Turn the ignition OFF.
2. Disconnect the C102 wiring connector and the
brake switch wiring connector.
3. Measure the resistance between the terminal
D5 of the C102 connector and the terminal 3 of
the brake switch wiring connector.
Is the resistance within the values shown?0ΩGo to Step 8Go to Step 7
7Repair the open circuit between the C102 connector
and the brake switch connector.
Is the action complete?–System OK–
81. Turn the ignition ON.
2. Measure the voltage of the C102 connector, 6
terminal.
Is the voltage within the values shown?11–14vGo to Step 9Go to Step 10
9Repair the short to power between the C102 con-
nector and the brake switch connector.
Is the action complete?–System OK–
101. Turn the ignition OFF.
2. Disconnect the brake switch wiring connector
and TCM wiring connector.
3. Measure between the brake switch connector,
terminal 4 and TCM connector, terminal A5.
Is the resistance within the values shown?0ΩSystem OKGo to Step 11
11Repair the open or short to ground between brake
switch connector and TCM.
Is the action complete?–System OK–
121. Turn the ignition ON.
2. Measure the voltage of the brake switch wiring
connector, terminal 4.
Is the voltage within the values shown?11–14vGo to Step 13Go to Step 14

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 85
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
13Repair the short to power between the brake switch
wiring connector and TCM.
Is the action complete?–System OK–
14Replace the TCM.
Is the action complete?–Go to Step 15–
151. After the repair, use a scan tool ”clear info”
function and road test the vehicle.
2. Review the ”DTC info”.
Has the last test failed or is the current DTC dis-
played?–Begin diagno-
sis againRepair verified
exit DTC chart

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 87
DAEWOO V–121 BL4
Gear Position And Range Signal Chart.
L1L2L3L4
P00120
R00012
N01200
D1212120
31212012
21201212
10121212
DTC P0705 – Transmission Range Sensor Circuit Malfunction
(PRNDL Input)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
21. Install the scan tool.
2. Turn the ignition ON.
3. Record then clear DTC(s) and turn the ignition
OFF, then turn the ignition ON.
4. Applying the brakes and select each transaxle
range (P, R,N,D,3,2,1), while monitoring scan
tool.
Refer to Gear Position And Range Signal Chart.
Does each selected transaxle range match scan tool
and signal range chart?–Go to Step 3Go to ”Diag-
nostic Aids”
3Inspect the F2 for open?
Was a problem found?–Go to Step 4Go to Step 5
4Replace the fuse as necessary.
Is the action complete?–System OK–
5Inspect the TR switch. Refer to ”Diagnostic Aids”.
Was the problem found?–Go to Step 6Go to Step 7
6Replace the TR switch.
Is the action complete?–System OK–
71. Disconnect the TR switch connector and TCM
connector.
2. Measure the resistance between terminal 3 of
the TR switch and terminal C1 of the TCM con-
nector.
3. Measure the resistance between terminal 2 of
the TR switch and terminal B15 of the TCM
connector.
4. Measure the resistance between terminal 4 of
the TR switch and terminal B6 of the TCM con-
nector.
5. Measure the resistance between terminal 5 of
the TR switch and terminal B11 of the TCM
connector.
Is the resistance within the values shown?0ΩGo to Step 9Go to Step 8

5A1 – 116IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0731
GEAR 1 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

5A1 – 118IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0732
GEAR 2 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716 or
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

5A1 – 120IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0733
GEAR 3 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.