intermitt relay DAEWOO LACETTI 2004 Service Owner's Manual
[x] Cancel search | Manufacturer: DAEWOO, Model Year: 2004, Model line: LACETTI, Model: DAEWOO LACETTI 2004Pages: 2643, PDF Size: 80.54 MB
Page 1120 of 2643

ANTILOCK BRAKE SYSTEM 4F – 39
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0080/C0085
LEFT REAR INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the left rear inlet and outlet
valves are functioning.
Cause(s)
S A valve has failed.S A solenoid coil is open or shorted.
Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve.
3. This tests the outlet valve.
Page 1122 of 2643

ANTILOCK BRAKE SYSTEM 4F – 41
DAEWOO V–121 BL4
J3B14F09
DLC
(Data Link
Connector)
EBCM
DK BLUDK BLU
BLK/WHTC202
C110
11 2
1912 19
G106
DIAGNOSTIC TROUBLE CODE (DTC) C0090/C0095
RIGHT REAR INLET AND OUTLET VALVE SOLENOID
FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake con-
trol module (EBCM) to each coil.
Diagnosis
This procedure checks whether the right rear inlet and out-
let valves are functioning.
Cause(s)
S A valve has failed.S A solenoid coil is open or shorted.
Fail Action
ABS is disabled, and the ABS warning lamp is turned ON
for the remainder of the ignition cycle. EBD is disabled. If
the failure is intermittent, the EBCM will enable the system
at the next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve.
3. This tests the outlet valve.
Page 1126 of 2643

ANTILOCK BRAKE SYSTEM 4F – 45
DAEWOO V–121 BL4
J3B14F04
60A Ef230A Ef5
2
42
C107 C105
2
C110
G106
A19
A13 A1 A14
C110 C202
C202WHT LT GRN
DK
GRN LT GRN/
BLK
BLK
DK BLUDK BLU
PPL/WHT
PPL/WHT ABS
TCS Parking
Brake
Hot at all times
RED REDRED/WHT
Ignition
Switch
RED
RED
I/P Cluster
EBCM8
20
22 2216 41
1211
18 1621
1
C107
10A F410AF11
32 31
43
6 62 C201
C201 C201C201
C110 C202
Hot in Run and Start
30
4
1711
C202
15
B15
DLC
(Data Link
Connector)12
G106
BLK/WHTOil Feeding
Connector
”2” Ter.
BRNBRN BRN
BRN PNK PNK PNK
19J1
59B1
ONStart Lock
Acc
IG1
19
DIAGNOSTIC TROUBLE CODE (DTC) C0121
VALVE RELAY CIRCUIT MALFUNCTION
Circuit Description
When the ABS is active, the valve relay provides voltage
to actuate the solenoid valves. The valves do not use this
voltage unless the ABS control module provides the
ground for each solenoid coil.
DTC C0121 will set if the valve relay voltage is low or if the
relay supply line is at 12 volts when the ABS control mod-
ule is not requesting it. This DTC will also set if the ABS
control module detects three or more solenoid valve cir-
cuits are open or shorted during the self–test.
Diagnosis
This procedure checks whether there is a poor ground
connection for the electronic brake control module
(EBCM).Cause(s)
S A connector terminal is corroded.
S The wiring harness is damaged.
S The ground terminal is not conducting properly.
S The EBCM is defective.
Fail Action
ABS/EBD is disabled, and the ABS / EBD warning lamp
is turned ON for the remainder of the ignition cycle. If the
failure is intermittent, the control module will enable the
system at the next ignition cycle and set a history DTC
C0121.
Diagnostic Aids
It is very important to perform a thorough inspection of the
wiring and the connectors. Failure to do so may result in
misdiagnosis, causing part replacement with reappear-
ance of the malfunction.
Page 1127 of 2643

4F – 46IANTILOCK BRAKE SYSTEM
DAEWOO V–121 BL4
DTC C0121 – Valve Relay Circuit Malfunction
StepActionValue(s)YesNo
11. Use a scan tool to clear all DTCs.
2. Road test the vehicle.
Does DTC C0121 set again?–Go to Step 3Go to Step 2
21. Check all system wiring harness connectors
and terminals, especially the EBCM, for any
problem that could cause an intermittent condi-
tion.
2. Repair any intermittent problem found.
Is the repair complete?–System OK–
31. Disconnect ABS harness connector J1 from
the EBCM.
2. Examine terminal 19 on the harness connector
and the EBCM connector.
Is there damage or corrosion at terminal 19?–Go to Step 4Go to Step 5
4Repair the terminal or the connector, or replace the
ABS harness or ABS unit as required.
Is the resistance equal to the specified value?–System OK–
5Measure the resistance from terminal 19 of the har-
ness connector J1 to a good chassis ground.
Is the resistance equal to the specified value? 0 WGo to Step 6Go to Step 7
6Replace the ABS unit.
Is the repair complete?–System OK–
7Measure the resistance from terminal 19 of the har-
ness connector J1 to the ground lug at G106.
Is the resistance equal to the specified value? 0 WGo to Step 8Go to Step 9
8Repair the chassis connection at the ground lug.
Is the repair complete?–System OK–
9Repair the open or the high resistance in the ABS
harness, or replace the harness as required.
Is the repair complete?–System OK–
Page 2285 of 2643

9D – 8IWIPERS/WASHER SYSTEMS
DAEWOO V–121 BL4
Wipers Do Not Work On Intermittent (INT), Other Speeds OK
StepActionValue(s)YesNo
11. Turn the ignition ON.
2. Turn the wiper switch to INT.
3. Check the voltage at wiper motor connector
terminal 2.
Does the voltmeter indicate a voltage equal to the
specified value?11–14 vGo to Step 5Go to Step 2
2Check for an open circuit between wiper switch con-
nector terminal B2 and wiper motor connector termi-
nal 2.
Is there an open circuit?–Go to Step 4Go to Step 3
3Replace the wiper switch.
Is the repair complete?–System OK–
4Repair the open circuit between wiper switch con-
nector terminal B2 and wiper motor connector termi-
nal 2.
Is the repair complete?–System OK–
51. Turn the ignition ON.
2. Turn the wiper switch to INT.
3. Check for pulsing voltage at wiper motor con-
nector terminal 6.
Does the voltmeter indicate a pulsating voltage
equal to the specified value?11–14 vGo to Step 7Go to Step 6
6Replace the wiper motor.
Is the repair complete?–System OK–
71. Ignition ON.
2. Check the voltage at the wiper switch connec-
tor terminal A6.
Is voltage pulsating at the specified value?11–14 vGo to Step 8Go to Step 9
8Replace the wiper switch.
Is the repair complete?–System OK–
9Repair the open circuit between the wiper switch and
the wiper motor.
Is the relay complete?–System OK–