check engine light DAEWOO LACETTI 2004 Service Manual PDF

ENGINE CONTROLS 1F – 237
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
61. Disconnect the EVAP canister purge valve con-
nector.
2. Connect a test light between the EVAP canister
purge valve connector terminal 1 and battery.
Is the test light ON?–Go to Step 7Go to Step 9
71. Disconnect the ECM connector.
2. Connect a test light between the ECM connec-
tor terminal 65 and ground.
Is the test light ON?–Go to Step 8Go to Step 10
81. Repair the low voltage in the wire between the
EVAP canister purge valve connector terminal
2 and the ECM connector terminal 65.
2. Clear any Diagnostic Trouble Codes (DTCs)
from the ECM.
3. Perform the diagnostic system check.
Is the repair complete?–System OK–
91. Replace the EVAP canister purge valve.
2. Clear any Diagnostic Trouble Codes (DTCs)
from the ECM.
3. Perform the diagnostic system check.
Is the repair complete?–Go to Step 10–
101. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 11Go to Step 2
11Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 246IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 10 in the relay control circuit
in the ECM harness connector to ground.
Does the DVM display infinite resistance?–Go to Step 12Go to Step 10
51. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil ter-
minals 86 and 85 in the relay harness connec-
tor.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON
and OFF.
Does the test light turn ON and OFF with each com-
manded?–Go to Step 8Go to Step 6
6With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?–Go to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 10 in
the ECM harness connector.
Does the relay operate?–Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
141. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 249
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 10 in the relay control circuit
in the ECM harness connector to ground.
Does the DVM display infinite resistance?–Go to Step 12Go to Step 10
51. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil ter-
minals 86 and 85 in the relay harness connec-
tor.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON
and OFF.
Does the test light turn ON and OFF with each com-
manded?–Go to Step 8Go to Step 6
6With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?–Go to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 10 in
the ECM harness connector.
Does the relay operate?–Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
141. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 252IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 9 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?–Go to Step 12Go to Step 10
51. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil ter-
minals 86 and 85 in the relay harness connec-
tor.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON
and OFF.
Does the test light turn ON and OFF with each com-
manded?–Go to Step 8Go to Step 6
6With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?–Go to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 9 in
the ECM harness connector.
Does the relay operate?–Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
141. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 255
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 9 in the high speed cooling
fan relay control circuit in the ECM harness
connector to ground.
Does the DVM display infinite resistance?–Go to Step 12Go to Step 10
51. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil ter-
minals 86 and 85 in the relay harness connec-
tor.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON
and OFF.
Does the test light turn ON and OFF with each com-
manded?–Go to Step 8Go to Step 6
6With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?–Go to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 9 in
the ECM harness connector.
Does the relay operate?–Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–

ENGINE CONTROLS 1F – 265
DAEWOO V–121 BL4
DTC P0532 – A/C Pressure Sensor Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed? –Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Idle the engine.
Does the scan tool display Air Conditioning Pressure
(ACP) sensor voltage below the specified value?0.06 VGo to Step 3Go to Step 4
31. Turn the ignition OFF.
2. Disconnect the ACP sensor connector.
3. Jumper the ACP signal circuit, terminal 2 to the
5 volt reference circuit, terminal 1.
4. Turn the ignition switch on.
Does the ACP voltage read more than the specified
value?4.9 VGo to Step 5Go to Step 6
41. Turn the ignition ON, with the engine OFF.
2. Operate the vehicle within the Failure Record
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display ACP voltage below the
specified value?0.06 VGo to Step 3Go to
”Diagnostic
Aids”
5Inspect the ACP sensor harness connector termi-
nals for the following conditions:
S Poor connections
S Proper contact tension
S Poor terminal–to–wire connection
Is a problem found?–Go to Step 8Go to Step 9
61. Turn the ignition OFF.
2. Remove the jumper wire.
3. Probe the ACP sensor signal circuit terminal 2
with a test light to B+.
4. Turn the ignition ON.
Does the scan tool read over the specified value?4 VGo to Step 7Go to Step 11
7Check the ACP sensor 5 volt reference circuit for an
open or short to ground and repair as needed.
Is the repair complete?–Go to Step 13Go to Step 10
8Repair the connection terminals as necessary.
Is the repair complete?–Go to Step 13–
91. Turn the ignition OFF.
2. Replace the ACP sensor.
Is the repair complete?–Go to Step 13–
101. Turn the ignition OFF.
2. Replace the engine control module (ECM).
Is the repair complete?–Go to Step 13–

1F – 268IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0533 – A/C Pressure Sensor High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Idle the engine.
Does the scan tool display Air Conditioning Pressure
(ACP) sensor voltage below the specified value?0.06 VGo to Step 3Go to Step 4
31. Turn the ignition OFF.
2. Disconnect the ACP sensor connector.
3. Jumper the ACP signal circuit, terminal 2 to the
5 volt reference circuit, terminal 1.
4. Turn the ignition switch on.
Does the ACP voltage read more than the specified
value?4.9 VGo to Step 5Go to Step 6
41. Turn the ignition ON, with the engine OFF.
2. Operate the vehicle within the Failure Record
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display ACP voltage below the
specified value?0.06 VGo to Step 3Go to
”Diagnostic
Aids”
5Inspect the ACP sensor harness connector termi-
nals for the following conditions:
S Poor connections
S Proper contact tension
S Poor terminal–to–wire connection
Is a problem found?–Go to Step 8Go to Step 9
61. Turn the ignition OFF.
2. Remove the jumper wire.
3. Probe the ACP sensor signal circuit terminal 2
with a test light to B+.
4. Turn the ignition ON.
Does the scan tool read over the specified value?4 VGo to Step 7Go to Step 11
7Check the ACP sensor 5 volt reference circuit for an
open or short to ground and repair as needed.
Is the repair complete?–Go to Step 13Go to Step 10
8Repair the connection terminals as necessary.
Is the repair complete?–Go to Step 13–
91. Turn the ignition OFF.
2. Replace the ACP sensor.
Is the repair complete?–Go to Step 13–
101. Turn the ignition OFF.
2. Replace the engine control module (ECM).
Is the repair complete?–Go to Step 13–

ENGINE CONTROLS 1F – 271
DAEWOO V–121 BL4
DTC P0562 – System Voltage(Engine Side) Too Low
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool and clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and raise the engine speed to
the specified value.
3. Load the electrical system by turning on the
headlights, high blower motor, etc.
Is the ignition voltage less than the specified value?1,400rpm 10VGo to Step 3Go to Step 8
31. With the engine still running at the specified
value.
2. Using a digital voltmeter(DVM), measure the
battery voltage at the battery.
Is the battery voltage greater than the specified val-
ue?1,400rpm 12VGo to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch to LOCK.
2. Disconnect the engine control module(ECM)
connector at the ECM.
3. Turn the Turn the ignition switch to ON with the
engine OFF.
4. Using a DVM, measure the ignition voltage at
the ignition feed circuit, terminal 29.
Is the ignition voltage greater than the specified val-
ue?10VGo to Step 5Go to Step 6
5Check for a malfunctioning connection at the ECM
harness terminals and repair as necessary.
Is a repair necessary?–Go to Step 8Go to Step 7
6Repair the poor connection (high resistance) in the
ignition feed circuit.
Is the repair complete?–Go to Step 8–
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
81. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 9Go to Step 2
9Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 273
DAEWOO V–121 BL4
DTC P0563 – System Voltage(Engine Side) Too High
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool and clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and raise the engine speed to
the specified value.
3. Load the electrical system by turning on the
headlights, high blower motor, etc.
Is the ignition voltage less than the specified value?1,400rpm 10VGo to Step 3Go to Step 8
31. With the engine still running at the specified
value.
2. Using a digital voltmeter(DVM), measure the
battery voltage at the battery.
Is the battery voltage greater than the specified val-
ue?1,400rpm 12VGo to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch to LOCK.
2. Disconnect the engine control module(ECM)
connector at the ECM.
3. Turn the Turn the ignition switch to ON with the
engine OFF.
4. Using a DVM, measure the ignition voltage at
the ignition feed circuit, terminal 29.
Is the ignition voltage greater than the specified val-
ue?10VGo to Step 5Go to Step 6
5Check for a malfunctioning connection at the ECM
harness terminals and repair as necessary.
Is a repair necessary?–Go to Step 8Go to Step 7
6Repair the poor connection (high resistance) in the
ignition feed circuit.
Is the repair complete?–Go to Step 8–
7Replace the ECM.
Is the replacement complete?–Go to Step 8–
81. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 9Go to Step 2
9Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 284IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1230 – Fuel Pump Relay Low Voltage (1.4L DOHC)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to LOCK for 10 sec-
onds.
2. Turn the Turn the ignition switch to ON.
3. Listen for in–tank fuel pump operation.
Does the fuel pump operate?2.55 secondsGo to
”Diagnostic
Aids”Go to Step 3
31. Turn the ignition switch to ON.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump
relay connector terminal 85 and ground.
4. Turn the Turn the ignition switch to ON.
Is the test light ON?–Go to Step 4Go to Step 10
41. Turn the ignition switch to ON.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump
relay connector terminal 86 and B+.
4. Turn the Turn the ignition switch to ON.
Is the test light ON?–Go to Step 5Go to Step 9
51. Turn the ignition switch to LOCK.
2. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Is the test light ON?–Go to Step 6Go to Step 8
6Check for short to ground in the wire between the
fuel pump relay connector terminal 87 and fuel pump
connector.
Is the problem found?–Go to Step 7Go to Step 8
71. Repair the wire between the fuel pump relay
connector terminal 87 and fuel pump connector
terminal 3.
2. Install the fuel pump relay.
3. Turn the engine OFF for 10 seconds.
4. Clear any DTCs from ECM.
5. Turn the ignition switch to ON.
Does the fuel pump operate?2.55 secondsGo to Step 14–
81. Replace the fuel pump relay.
2. Turn the ignition OFF for 10 seconds.
3. Clear any DTCs from ECM.
4. Turn the Turn the ignition switch to ON.
Does the fuel pump operate?2.55 secondsGo to Step 14Go to Step 9
9Check for a short to ground wire between the fuel
pump relay connector terminal 86 and the ignition af-
ter key ON(IGN 1).
Is the problem found?–Go to Step 11Go to Step 10
10Check for a short to ground wire between the fuel
pump relay connector terminal 85 and the ECM con-
nector terminal 6.
Is the problem found?–Go to Step 12Go to Step 13