turn signal DAEWOO MATIZ 2003 Service Repair Manual

9B–16 LIGHTING SYSTEMS
DAEWOO M-150 BL2
SPECIFICATIONS
BULB USAGE CHART
BulbReplacement Bulb Number
Backup Lamp(s)21W
Center High Mounted Stoplamp21W
HeadlampsDouble 60/55W
Interior Courtesy Lamp10W
License Plate Lamp5W
Front Turn Signal Lamps21W
Rear Fog Lamp21W
Rear Turn Signal Lamps21W
Side Marker Turn Signal Lamps5W
Tail and StoplampDouble 5/21W, 5W
Parking Lamp5W

9E –22 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

Application

Nm

Lb-Ft

Lb-In
Passenger’s Airbag Module Blank Cover Screw

1.5–2

–

13–18
INSTRUMENT CLUSTER INDICATOR LAMPS SPECIFICATIONS
Indicator Lamp Color Bulb
ABS Warning Amber 14 v 1.4 W
Airbag Warning Red 14 v 1.4 W
Battery Charge Indicator Red 14 v 1.4 W
Fasten Seat Belt Warning Red 14 v 1.4 W
High Beam Indicator Blue 14 v 1.4 W
Low Fuel Level Warning Amber 12 v 3 W Oil Pressure Warning Red 14 v 1.4 W Parking Brake Indicator and Brake Fluid Warning Red 14 v 1.4 W Service Engine Soon Warning Amber 14 v 1.4 W
Turn Signal Indicators

Green

14 v 1.4 W
Instrument Cluster IlluminationBlue12 v 3 W
Rear Fog Lamp IndicatorAmber14 v 1.4 W

9M –4 EXTERIOR TRIM
DAEWOO M-150 BL2
D19E589A
3. Remove the rear spoiler from the tailgate.

Remove the nuts (1).

Remove the rear spoiler (2).
D19E590A
Installation Procedure
1. Install the rear spoiler on the tailgate with the nuts.
2. Install the spoiler seals.
D209B109
FRONT BUMPER SPACER
Removal Procedure
1. Support the hood suitably.
2. Disconnect the negative battery cable.
3. Remove the front bumper spacer.

Remove the bolts (1).

Remove the front bumper spacer from the bumper
fascia (2).
4. Remove the turn signal lamps. Refer to Section 9B,
Lighting Systems.
D209B110
Installation Procedure
1. Install the turn signal lamps. Refer to Section 9B,
Lighting Systems.
2. Install the front bumper spacer with the bolts.
3. Connect the negative battery cable.

9T–2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can per-
form the following functions:

Remotely lock and unlock the vehicle doors with a
hand-held high-frequency transmitter.

Sense intrusion into the vehicle through the doors,
the tailgate, or the hood.

Activate a warning to signal an intrusion.

Help the driver find the vehicle in a parking area.

Automatically re-lock the doors if a door or the trunk is
not opened within 30 seconds after the vehicle has
been unlocked by the remote keyless entry.

Communicate serial data to a scan tool to help diag-
nose system faults.
The remote keyless entry and anti-theft system consists
of the following components:

Keyless entry and anti-theft control module/receiver.

Security indicator.

Tailgate open switch.

Door open switches.

Central locking unit.

Flashing turn signal lamps.

Siren.

Hood open switch.
REMOTE LOCKING AND UNLOCKING
The hand-held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmit-
ter varies between 5 and 10 meters (approximately 16 to
32 feet), depending on whether or not objects such as
other vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK
button which only function when the ignition is OFF.
Pressing the UNLOCK button has the following effects:

The doors are unlocked.

The turn signal lamps flash twice.

The control module is disarmed.
Pressing the LOCK button has the following effects:

The doors are locked.

The turn signal lamps flash once.

The control module is armed.
The transmitter has a replaceable battery. The battery is
designed to last at least two years before replacement is
necessary.
SECURITY INDICATOR
There is a security indicator on the instrument panel. Af-
ter the LOCK button of the transmitter is pressed, the
module is placed in the armed mode, and the security
indicator flashes. The security indicator turns ON for 1/8
second and OFF for 7/8 second. It then flashes at that
frequency until the control module/receiver is disarmed.
INTRUSION SENSING
The anti-theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF.
When the hood, the door, or the tailgate is opened, the
hood open switch, the door open switch, or the tailgate
open switch will change its input to ground. The alarm
will be activated if the hood open sensor, the door open
sensor, or the tailgate open sensor changes its input to
ground before either of the following conditions occurs:

An UNLOCK message is received from the transmit-
ter.
SIREN
The remote keyless entry system is armed when the
LOCK message is received from the transmitter when
the ignition is OFF. When the system is armed, it will ac-
tivate the siren and flash the turn signals for 28 seconds
if any of the following conditions occurs:

A door is opened (front door open switch input is
changed to ground).

The tailgate is opened (tailgate open switch input is
changed to ground).

The hood is opened while the anti-theft system is
armed (hood open switch input is changed to
ground).
The siren is disarmed when any of the following condi-
tions occurs:

The ignition switch is turned ON with the key.

The UNLOCK button or the LOCK button on the re-
mote transmitter is pressed.
VEHICLE LOCATOR
The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate
the location of the vehicle. The duration of the flashes
and the length of time between flashes is used to indi-
cate certain vehicle conditions. Refer to “Fault or Alarm
Indication” in this section.

REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM 9T–3
DAEWOO M-150 BL2
AUTOLOCKING (SAFETY LOCK)
The remote keyless entry system features an autolock-
ing control. If the doors are unlocked with the remote
transmitter when the control module/receiver is in the
armed mode, the doors are automatically re-locked after
30 seconds unless any of the following events occur:

The door is opened.

The ignition switch is turned ON.

The tailgate is opened.

The hood is opened.
CONTROL MODULE/RECEIVER
The remote keyless entry control module/receiver is
contained in the tie-bar center. The module/receiver pro-
cesses signals from the remote transmitter and the in-
trusion sensors, and it activates the alarm if an intrusion
is detected.
The control module/receiver will not communicate with
transmitters from other vehicles because there are over
four billion possible electronic password combinations,
and passwords are not duplicated. The control module/
receiver has an attached antenna to detect signals from
the transmitter.

9T–14 IMMOBILIZER ANTI-THEFT SYSTEM
DAEWOO M–150 BL2
D19T002B
DIAGNOSTIC TROUBLE CODE (DTC) 1600
ECM IMMOBILIZER ERROR (NO ANSWER)
Circuit Description
When the ignition is turned ON, the key is tested by the
immobilizer anti-theft system. While the key code is be-
ing read by the immobilizer control unit, the engine can
start and run with any key that will turn the lock cylinder.
The key code is read and compared with key codes that
have been stored in the memory of the immobilizer con-
trol unit. If a valid key is detected, the immobilizer control
unit sends a serial data release message to the elec-
tronic control module (ECM). Included in the release
message is an identification (ID) code which assures
that neither the immobilizer control unit nor the ECM has
been substituted to defeat the system. If the ECM re-
ceives an invalid release message, the ECM performs
the following actions:
Disables the fuel injector circuit.

Disables the fuel pump circuit.

Disables the ignition coil.
DTC Will Set When

The ECM does not receive the signal from the immo-
bilizer control module when the ignition is turned on.

The above conditions are maintained until the ignition
is switched OFF.
DTC 1600 Will Clear When

The ignition switch is turned OFF or the scan tool
TROUBLE CODE CLEAR command is issued.

9T–20 IMMOBILIZER ANTI-THEFT SYSTEM
DAEWOO M–150 BL2
D209T002
DIAGNOSTIC TROUBLE CODE (P) 1628 (SIRIUS D3)
ECM IMMOBILIZER ERROR (NO SUCCESSFUL COMMUNICATION)
Circuit Description
When the ignition is turned ON, the key is tested by the
immobilizer anti-theft system. While the key code is be-
ing read by the immobilizer control unit, the engine can
start and run with any key that will turn the lock cylinder.
The key code is read and compared with key codes that
have been stored in the memory of the immobilizer con-
trol unit. If a valid key is detected, the immobilizer control
unit sends a serial data release message to the elec-
tronic control module (ECM). Included in the release
message is an identification (ID) code which assures
that neither the immobilizer control unit nor the ECM has
been substituted to defeat the system. If the ECM re-ceives an invalid release message, the ECM performs
the following actions:

Disables the fuel injector circuit.
P 1628 Will Set When

The ECM does not receive the signal from the immo-
bilizer control module within 1.260 seconds after the
ignition is turned on.

The above conditions are maintained until the ignition
is switched OFF.
P 1628 Will Clear When

The ignition switch is turned OFF or the scan tool
TROUBLE CODE CLEAR command is issued.