light DAEWOO MATIZ 2003 Service Repair Manual

IMMOBILIZER ANTI-THEFT SYSTEM 9T–19
DAEWOO M–150 BL2
DTC 1602 – ECM Immobilizer Error (ECM Locked)
StepActionValueYesNo
1
Connect the scan tool using the following procedure:
1. Insert the cartridge into the scan tool.
2. Turn the ignition switch to the OFF.
3. Connect the scan tool to the data link connector
(DLC).
4. Connect the scan tool’s power cord to the cigar
lighter socket.
5. Turn the ignition ON, but do not start the engine.
Is communication established between the scan tool
and the immobilizer control unit?
–
Go to Step 2
Go to
“Communi-
cation
Between
Immobilizer
and Test
Equipment”
2
1. Select CURRENT KEY STATUS from the scan
tool menu.
2. Read the STATUS OF CURRENT KEY message.
Does the KEY STATUS message indicate “KEY IS
WRONG”?
–
Go to “Key
Status Errors”
Go to Step 3
3
1. Select DIAGNOSIS from the scan tool menu.
2. Read the IMMO & ECM ID CODE (immobilization
and electronic control module identification code)
message.
Did the message differ from normal message?
Normal Message –ECM MODE: LEARNT
IMMO. MODE: LEARNT
VIN CODE: SAME
–Go to
“Identification
(ID) Code
Repro-
gramming”
Go to Step 4
4
Check for an open serial data wire between the
immobilizer control unit and the electronic control
module (ECM).
Was the circuit open?
–
Go to Step 5Go to Step 6
5
Repair the open serial data wire between the ECM
and the immobilizer control unit.
Is the repair complete?
–
System OK
–
6
1. Replace the ECM.
2. Reprogram the ID code.
Is the repair complete?
–
System OK
–

IMMOBILIZER ANTI-THEFT SYSTEM 9T–21
DAEWOO M–150 BL2
P 1628 – ECM Immobilizer Error (No Successful Communication)
StepActionValueYesNo
1
Connect the scan tool using the following procedure:
1. Insert the cartridge into the scan tool.
2. Turn the ignition switch to the OFF position.
3. Connect the scan tool to the data link connector
(DLC).
4. Connect the scan tool’s power cord to the cigar
lighter socket.
5. Select immobilizer mode on the scan tool.
6. Turn the ignition ON, but do not start the engine.
Is communication established between the scan tool
and the immobilizer control unit?
–
Go to Step 2
Go to
“Communi-
cation
Between
Immobilizer
and Test
Equipment”
2
Read the IMMO & ECM ID CODE message that
was displayed after requesting DIAGNOSIS.
Did the message differ from normal message?
Normal Message –ECM MODE: LEARNT
IMMO. MODE: LEARNT
VIN CODE: SAME
–
Go to
“Identification
(ID) Code
Repro-
gramming”
Go to Step 3
3
Check for an open serial data wire between the
immobilizer control unit and the ECM.
Was the circuit open?
–
Go to Step 4Go to Step 5
4
Repair the open serial data wire between the ECM
and the immobilizer control unit.
Is the repair complete?
–
System OK
–
5
1. Replace the immobilizer.
2. Reprogram the identification (ID) code. Refer to
“Identification (ID) Code Reprogramming” in this
section.
Is the repair complete?
–
System OK
–
Go to Step 6
6
1. Replace the ECM.
2. Turn the ignition ON, OFF for more than 4
seconds.
3. Turn the ignition ON.
Is the repair complete?
–
System OK
–

IMMOBILIZER ANTI-THEFT SYSTEM 9T–23
DAEWOO M–150 BL2
P 1629 – ECM Immobilizer Error (Incorrect Answer)
StepActionValueYesNo
1
Connect the scan tool using the following procedure:
1. Insert the cartridge into the scan tool.
2. Turn the ignition switch to the OFF.
3. Connect the scan tool to the data link connector
(DLC).
4. Connect the scan tool’s power cord to the cigar
lighter socket.
5. Turn the ignition ON, but do not start the engine.
Is communication established between the scan tool
and the immobilizer control unit?
–
Go to Step 2
Go to
“Communi-
cation
Between
Immobilizer
and Test
Equipment”
2
1. Select DIAGNOSIS from the scan tool menu.
2. Read the IMMO & ECM ID CODE (immobilization
and electronic control module identification code)
message.
Did the message differ from normal message?
Normal Message –ECM MODE: LEARNT
IMMO. MODE: LEARNT
VIN CODE: SAME
–Go to
“Identification
(ID) Code
Repro-
gramming”
Go to Step 3
3
1. Replace the ECM.
2. Reprogram the ID code.
Is the repair complete?
–
System OK
–
Go to Step 4
4
1. Replace the ECM.
2. Turn the ignition ON, OFF for more than 4
seconds.
3. Turn the ignition ON.
Is the repair complete?
–
System OK
–