change time DAEWOO MATIZ 2003 Service Owner's Guide

MANUAL CONTROL HEATING, VENTILATION, AND AIR CONDITIONING SYSTEM 7B–15
DAEWOO M-150 BL2
Refrigerant Recovery
Important: Use only a refrigerant tank that is designed
for the charging station in use. The unit’s overfill limita-
tion mechanism is calibrated specifically for use with this
tank. The tank’s valves are also specifically for this unit.
1. Attach the high side hose with the quick disconnect
coupler to the high side fitting of the vehicle’s A/C
system.
2. Open the coupler valve after attachment.
3. Attach the low side hose with the quick disconnect
coupler to the low side fitting of the vehicle’s A/C
system.
4. Open the coupler valve after attachment.
5. Check the high side and the low side gauges on the
unit’s control panel in order to ensure that the A/C
system has pressure. If there is no pressure, there
is no refrigerant in the system to recover.
Important: If there is no refrigerant in the system, do
not continue with the recovery operation. This will draw
air into the recovery tank.
6. Open both the high side and the low side valves.
7. Open the gas and the liquid valves on the tank.
8. Drain any oil that may be in the oil separator.
9. Close the oil drain valve.
10. Plug the unit into the proper voltage outlet.
11. Turn on the main power switch.
Notice: Never reuse refrigerant oil. Damage to the A/C
system may result. Dispose of the refrigerant oil proper-
ly.
12. Begin the recovery process. Refer to the manufac-
turer’s instructions for the charging station in use.
Important: Some A/C system PAG lubricating oil may
be removed with the refrigerant during recovery. The
amount of oil removed varies. A charging station sepa-
rates the oil from the refrigerant and allows a means of
determining how much oil was removed. Replace the
same amount of oil when you recharge the system. Re-
fer to the manufacturer’s instructions for the charging
station in use.
13. Wait 5 minutes. Check the control panel low side
gauge. If the A/C has maintained vacuum, the re-
covery is complete.
14. There is more refrigerant in the system if the low
side gauge pressure rises above zero. Recover the
additional refrigerant. Repeat this step until the sys-
tem maintains vacuum for two minutes.
Important: If the control indicator shows that the refrig-
erant tank is full during the recovery process and the unit
shuts off, install an empty unit tank to store the refriger-
ant needed for steps later in the procedure. Do not use
any other type of tank.
Evacuation
The unit tank must contain a sufficient amount of R-134a
refrigerant for charging. Check the amount of refrigerant
in the tank. If there is less than 3.6 kg (8 pounds) of re-
frigerant, add new refrigerant to the tank. Refer to the
manufacturer’s instructions for adding refrigerant.
1. Verify that the high side and the low side hoses are
connected to the A/C system. Open both the high
side and the low side valves on the unit’s control pan-
el.
2. Open both the gas and the liquid valves on the tank.
Important: Refer to the manufacturer’s instructions for
the charging station in use. It is necessary to evacuate
the system before recharging it with new or recycled re-
frigerant.
3. Start the vacuum pump and begin the evacuation
process. Non-condensable gases (mostly air) are au-
tomatically vented from the tank during the recycling
process. You may hear the pressure being released.
4. Check for leaks in the system. Refer to the manufac-
turer’s instructions for the charging station in use.
Important:
Change the vacuum pump oil frequently. Refer to the
manufacturer’s instructions for the charging station in
use.
A/C System Oil Charge Replenishing
Any oil removed from the A/C system during the recov-
ery process must be replenished at this time.
1. Use the correct graduated bottle of polyalkaline glycol
(PAG) oil for the R-134a system.
Important:
Keep the oil bottles tightly capped at all times to pro-
tect the oil from moisture and contamination.
Never open the oil injection valve while there is posi-
tive pressure in the A/C system. This will result in oil
blow-back through the bottle vent. You must have
A/C system vacuum for this operation.
Never let the oil level drop below the pick-up tube
while charging or replenishing the system. This will
allow air into the A/C system.
2. Refer to the manufacturer’s instructions for the charg-
ing station in use. Add the proper amount of PAG oil
to the system.
3. Close the valve when the required oil charge has
been pulled into the system.
Charging
Important: Evacuate the air conditioning system before
charging.
1. Close the low side valve on the control panel.
2. Open the high side valve on the control panel.

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9F –2 AUDIO SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
STEREO CASSETTE AM/FM RADIO
WITH CD CHANGER AND
RDS/AUDIO SECURITY SYSTEM
The stereo digital logic cassette AM/FM radio with elec-
tronic tape ejection and the stereo digital logic cassette
AM/FM radio with a CD changer located under the front
seat (LH) are optional equipment.
The radio data system (RDS) uses a single button to se-
lect a specific radio station once it is set to the listener’s
preference.
The audio security system is activated whenever the au-
dio system circuit is disconnected from the battery. A
four-digit security code must be entered in order for the
audio system to be functional once again. The security
code is stamped on a card located in the vehicle (usually
in the glove box). One of the following security code en-
tering procedures can be followed.
With RDS
1. With the ignition switch in the I or II position, turn the
radio ON. At this time, “CODE” will be shown on the
radio display.
2. Press the P-UP button until the correct first digit is
shown on the display.
3. Press the P-DN button to move over to the second
digit and then press P-UP once again to enter the cor-
rect second digit.
4. Use steps two and three to enter the third and fourth
digits using the same method.
5. After entering the correct four-digit security code,
press the TP button. “CODE OK” will briefly appear
on the radio display, and the system is ready for use.
Wrong Code
If the wrong code is entered, “ERROR 1” will appear on
the display. After this, “CODE” will appear once again,
and the correct security code can be entered. The timebetween each new coding attempt is doubled; a total of
ten coding attempts can be made.
FRONT AND REAR SPEAKERS
All audio systems use four speakers: two speakers
mounted in the front doors and two speakers mounted in
the rear parcel side shelf.
ROOF ANTENNA
Roof antenna is located on the roof and is designed to
separate the antenna pole from the antenna base. The
antenna pole should be removed to prevent the painting
damage before washing the vehicle. The roof antenna
cannot be adjusted.
TAPE PLAYER AND CASSETTE CARE
The head and the capstan are the two parts of the tape
player that should be cleaned. This service should be
performed every 100 hours of cassette operation.
In order to clean the head and the capstan, use a cotton
swab dipped in rubbing alcohol.
A cassette cleaning kit may also be used to clean the
head and the capstan. Follow the cleaning kit instruc-
tions to clean the tape player.
Do not touch the tape head with magnetized tools. If the
head becomes magnetized, it will degrade cassettes
played in the player. No service is performed on the cas-
settes. The cassette manufacturer handles warranties
of the cassettes. Store cassettes away from extreme
heat and direct sunlight.
COMPACT DISC CARE
Handle discs carefully. Store the discs in protective
cases away from the sun, heat, and dust. If the surface
is soiled, dampen a clean, soft cloth in a solution of mild
neutral detergent and wipe the disc clean. Mini discs
(about 3 inches in diameter), will not eject and should
not be used.

9T–2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can per-
form the following functions:

Remotely lock and unlock the vehicle doors with a
hand-held high-frequency transmitter.

Sense intrusion into the vehicle through the doors,
the tailgate, or the hood.

Activate a warning to signal an intrusion.

Help the driver find the vehicle in a parking area.

Automatically re-lock the doors if a door or the trunk is
not opened within 30 seconds after the vehicle has
been unlocked by the remote keyless entry.

Communicate serial data to a scan tool to help diag-
nose system faults.
The remote keyless entry and anti-theft system consists
of the following components:

Keyless entry and anti-theft control module/receiver.

Security indicator.

Tailgate open switch.

Door open switches.

Central locking unit.

Flashing turn signal lamps.

Siren.

Hood open switch.
REMOTE LOCKING AND UNLOCKING
The hand-held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmit-
ter varies between 5 and 10 meters (approximately 16 to
32 feet), depending on whether or not objects such as
other vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK
button which only function when the ignition is OFF.
Pressing the UNLOCK button has the following effects:

The doors are unlocked.

The turn signal lamps flash twice.

The control module is disarmed.
Pressing the LOCK button has the following effects:

The doors are locked.

The turn signal lamps flash once.

The control module is armed.
The transmitter has a replaceable battery. The battery is
designed to last at least two years before replacement is
necessary.
SECURITY INDICATOR
There is a security indicator on the instrument panel. Af-
ter the LOCK button of the transmitter is pressed, the
module is placed in the armed mode, and the security
indicator flashes. The security indicator turns ON for 1/8
second and OFF for 7/8 second. It then flashes at that
frequency until the control module/receiver is disarmed.
INTRUSION SENSING
The anti-theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF.
When the hood, the door, or the tailgate is opened, the
hood open switch, the door open switch, or the tailgate
open switch will change its input to ground. The alarm
will be activated if the hood open sensor, the door open
sensor, or the tailgate open sensor changes its input to
ground before either of the following conditions occurs:

An UNLOCK message is received from the transmit-
ter.
SIREN
The remote keyless entry system is armed when the
LOCK message is received from the transmitter when
the ignition is OFF. When the system is armed, it will ac-
tivate the siren and flash the turn signals for 28 seconds
if any of the following conditions occurs:

A door is opened (front door open switch input is
changed to ground).

The tailgate is opened (tailgate open switch input is
changed to ground).

The hood is opened while the anti-theft system is
armed (hood open switch input is changed to
ground).
The siren is disarmed when any of the following condi-
tions occurs:

The ignition switch is turned ON with the key.

The UNLOCK button or the LOCK button on the re-
mote transmitter is pressed.
VEHICLE LOCATOR
The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate
the location of the vehicle. The duration of the flashes
and the length of time between flashes is used to indi-
cate certain vehicle conditions. Refer to “Fault or Alarm
Indication” in this section.