dimensions DAEWOO MATIZ 2003 Service Repair Manual

TIRES AND WHEELS 2E–3
DAEWOO M-150 BL2
Hydroplaning
The condition of driving a vehicle fast on the road surface
covered with water can cause tires to fail to rotate with a
good contact on the surface, so results in remaining them
afloat. This is so–called hydroplaning. It causes brake
failure, lower tractive force, and losing the steering per-
formance so it is very vulnerable condition.
D16A005A
Standing Wave
During running the rotating tire repeats deformation and
restoring movement generated in tread. But when the
wheel rotating speed reaches high, the next deformation
applied to tire before restoring last deformation so the
trembling wave appears in the tread portion. The lower
the tire pressure the severe the trembling wave appears.
And during the high speed.
D106A004
REPLACEMENT TIRES
A Tire Performance Criteria (TPC) specification number
is molded in the sidewall near the tire size of all original
equipment tires. This specification number assures that
the tire meets performance standards for traction, en-
durance, dimensions, noise, handling and rolling resist-
ance. Usually a specific TPC number is assigned to
each tire size.Caution: Do not mix different types of tires on the
same vehicle such as radial, bias and bias-belted
tires except in emergencies, because vehicle han-
dling may be seriously affected and may result in
loss of control.
Caution: Do not change 145/70 R13 tires or 155/65
R13 tires for 175/60 R13 tires, because vehicle
hancling may be seriously affected and may result
in loss of control. If you change 145/70 R13 tires or
155/65 R13 tires for 175/60 R13 tires, you have to
change the steering gear assembly.
Use only replacement tires with the same size, load
range, and construction as the original. The use of any
other tire size or construction type may seriously affect
ride, handling, speedometer/odometer calibration, ve-
hicle ground clearance, and tire clearance to the body
and the chassis. This does not apply to the spare tire fur-
nished with the vehicle.
It is recommended that new tires be installed in pairs on
the same axle.
If it is necessary to replace only one tire, pair it with the
tire having the most tread to equalize the braking action.
Although they may appear different in tread design, tires
built by different manufacturers with identical TPC speci-
fications may be used on the same vehicle.
ALL SEASON TIRES
Most vehicles are now equipped with steel-belted all
season radial tires as standard equipment. These tires
qualify as snow tires, with a 37 percent higher average
rating for snow traction than the non-all season radial
tires previously used. Other performance areas, such as
wet traction, rolling resistance, tread life, and air reten-
tion, have also been improved. This was done by im-
provements in both tread design and tread compounds.
These tires are identified by an “M + S” molded in the tire
sidewall following the size number. The suffix “MS” is
also molded in the sidewall after the TPC specification
number.
The optional handling tires used on some vehicles are
not all season tires. These will not have the “MS” mark-
ing after the tire size or the TPC specification number.
TIRE LABEL
The tire label is permanently located on the rear face of
the driver’s door and should be referred to for tire infor-
mation. It lists the maximum vehicle load, the tire size
(including the spare tire), and the cold inflation pressure
(including the spare tire).
SPARE TIRE
This vehicle comes equipped with a full-sized spare tire
and wheel.

DAEWOO M-150 BL2
SECTION 9N
FRAME AND UNDERBODY
TABLE OF CONTENTS
Description and Operation 9N-2. . . . . . . . . . . . . . . . . .
General Body Construction 9N-2. . . . . . . . . . . . . . . . .
Transaxle Under Covers 9N-2. . . . . . . . . . . . . . . . . . . .
Repair Instructions 9N-3. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9N-3. . . . . . . . . . . . . . . . . . . . . . . . . . Alignment Checking 9N-3. . . . . . . . . . . . . . . . . . . . . . .
Floor Pan Insulators 9N-3. . . . . . . . . . . . . . . . . . . . . . .
Specifications 9N-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Underbody Dimensions 9N-4. . . . . . . . . . . . . . . . . . . .

FRAME AND UNDERBODY 9N–3
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
ALIGNMENT CHECKING
An accurate method of determining the alignment of the
underbody uses a measuring tram gauge. The tram
gauge set used to perform the recommended measuring
checks must include a vertical pointer able to reach
457 mm (18 inches).
Two types of measurements can be made with a tram
gauge: direct point-to-point measurements and mea-
surements calculated on a horizontal plane (datum line)
parallel to the underbody. Point-to-point measurements
are generally taken on steering and suspension engine
compartment parts and simply require the vertical point-
ers to be set equally.
For horizontal plane measurements, the vertical pointers
must be set as specified for each point to be measured.
Dimensions-to-gauge holes are measured to the center
of the holes and flush to the adjacent surface metal un-
less otherwise specified. It is recommended that the di-
agonal dimensions to the cross-body be checked on
both sides in order to verify the dimensional accuracy of
the vehicle underbody.
FLOOR PAN INSULATORS
The floor pan insulators have been designed for the
higher floor pan temperatures that result from the use
of the catalytic converter in the exhaust system. There-
fore, when servicing a vehicle, it is essential that any in-sulators that may have been disturbed or removed be
reinstalled in the original sequence and location. Also, if
an insulator needs to be replaced, use only the insula-
tion specified for that location on the floor pan.
When servicing or replacing interior insulators, observe
the following instructions.

Install the insulators in the original position and se-
quence. Butt the pieces together in order to avoid
gapping or overlapping.

If it is necessary to replace an insulator, use only the
specified insulation.

Use the original part to determine the amount of re-
placement material required and as a template for
cutting and fitting the new piece to the floor pan.

When installing the insulator, do not enlarge any cut-
outs or holes that are used for the attachment of interi-
or parts such as the instrument panel or the floor
console.

Route the cross-body harness for interior parts over
the floor pan insulators. Clip it in the original location.

Do not apply spray-on deadeners or trim adhesives to
the top of the floor pan at the area directly over the
catalytic converter or the muffler.
Any insulator service repair or replacement should be
the same thickness, size, and location as the original
installation in the vehicle.

9N –4 FRAME AND UNDERBODY
DAEWOO M-150 BL2
SPECIFICATIONS
UNDERBODY DIMENSIONS
Unit: mm (in.)
DBDM118A