oil capacity DAEWOO MATIZ 2003 Service Repair Manual

1A–14 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
 Application Description
  Maximum Speed 144 km/h (90 mph)
 Vehicle Capacity Gradeability 0.420 tan θ
 
Vehicle Capacity
 Minimum Turning Radius 4.5 m (14.8 ft)
  Bore × Stroke 68.5 × 72.0 mm (2.70 × 2.83 inch)
  Displacement 796 cm3 (48.6 in3)
  Compression Ratio 9.3 : 1
  Maximum Power 37.5 KW (6,000 rpm)
 
Engine Information
 Maximum Torque 68.6 Nm (50.59 lb-ft) (at 4,600 rpm)
Ignition Timing (Ignition Sequence)5 BTDC (1–3–2) / 10 BTDC (1–3–2)   
Air Conditioning System (ON)
 
1,000 ± 50 rpm  Idle Speed Air Conditioning System (OFF) 950 rpm  Engine Overhead Cam L–3 
 
 
 Ignition Type
 
 Direct Ignition System (DIS) /
High Energy Ignition (HEI)
  Distributor Optical Sensor Type
  Starter SD 80
   Unleaded BPR5EY–11, RN9YC4, WR8DCX
  Spark–Plug Leaded BPR5EY, RN9YC, WR8DC
  Fuel Injection Type MPI
  Fuel Pump Electric Motor Pump
Engine Part TypeFuel FilterCartridge Engine Part Type 
Lubricating Type
 
Forced Feed Type  Oil Pump Rotary Pump Type  Cooling Type Forced Water Circulation  Radiator Cross – Flow  Water Pump Centrifugal  Thermostat Pellet Type
  Air Cleaner Element Non Woven Fablic
  Muffler Catalytic Converter, Closed Circuit
  Battery MF
Engine PartEngine OilSJ Grade
SAE 5W30, SAE 10W30, SAE 15W40
CapacityRefrigerantFour Seasons   
Engine Disassembly
 
3.0 L (3.17 qt)   Oil Change (Including filter) 2.7 L (2.85 qt)  Engine Oil Oil Change (Not including filter) 2.5 L (2.64 qt)   Oil Level Gauge 1 L (1.06 qt) (MIN to MAX)  Coolant 3.8 L (4.02 qt) Engine Information Battery 12V–35 AH, 246 CCA
 Engine Information  

Generator

65 A
  Starter 0.8 kW
   Output Capacity 90 – 133 Lph
  Fuel Pump Output Pressure 380 kPa (55.1 Psi)
  Fuel Tank Capacity 35 L (9.2 gal), 38 L (10 gal)

DAEWOO M-150 BL2
SECTION 1E
ENGINE ELECTRICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1E-2. . . . . . . . . . . . . . . . . .
Battery 1E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ratings 1E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reserve Capacity 1E-2. . . . . . . . . . . . . . . . . . . . . . . . .
Cold Cranking Amperage 1E-2. . . . . . . . . . . . . . . . . . .
Built-In Hydrometer 1E-2. . . . . . . . . . . . . . . . . . . . . . . .
Charging Procedure 1E-3. . . . . . . . . . . . . . . . . . . . . . .
Charging Time Required 1E-3. . . . . . . . . . . . . . . . . . . .
Charging a Completely Discharged Battery
(Off the Vehicle) 1E-3. . . . . . . . . . . . . . . . . . . . . . . . .
Jump Starting Procedure 1E-3. . . . . . . . . . . . . . . . . . .
Generator 1E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging System 1E-4. . . . . . . . . . . . . . . . . . . . . . . . . .
Starter 1E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting System 1E-4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor 1E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Coil 1E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spark Plug 1E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 1E-6. . . . . . . . . . . . . . . . . . . . . . . .
Starting System 1E-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging System (A-type: MANDO) 1E-7. . . . . . . . . .
Charging System (B-type: DAC) 1E-8. . . . . . . . . . . . .
Ignition System 1E-9. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1E-10. . . . . .
Ignition System 1E-10. . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Load Test 1E-12. . . . . . . . . . . . . . . . . . . . . . . . Generator Output Test 1E-12. . . . . . . . . . . . . . . . . . . .
Generator System Check 1E-13. . . . . . . . . . . . . . . . . .
Repair Instructions 1E-14. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1E-14. . . . . . . . . . . . . . . . . . . . . . . . .
Starter 1E-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generator 1E-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery 1E-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor 1E-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Coil 1E-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 1E-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Motor 1E-19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generator (A-type: MANDO) 1E-24. . . . . . . . . . . . . . .
Generator (B-type: DAC) 1E-29. . . . . . . . . . . . . . . . . .
Distributor Assembly 1E-34. . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 1E-37. . . . . . . . . .
Starting System 1E-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Charging System 1E-38. . . . . . . . . . . . . . . . . . . . . . . . .
Ignition System Circuit – Tipical 1E-39. . . . . . . . . . . .
Ignition System Circuit – Euro III 1E-40. . . . . . . . . . .
Specifications 1E-41. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Specifications 1E-41. . . . . . . . . . . . . . . . . . . . .
Generator Specifications 1E-41. . . . . . . . . . . . . . . . . .
Ignition System Specifications 1E-41. . . . . . . . . . . . . .
Battery Specifications 1E-41. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1E-42. . . . . . . . . .

ENGINE ELECTRICAL 1E–41
DAEWOO M-150 BL2
SPECIFICATIONS
STARTER SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
Starter MotorType–SD 80–
Output(Capacity)kW0.8–
No Load Test @ 9 volts
Drive Pinion SpeedA
RPM150
2,000–
Brushes Lengthmm (in.)11.3–11.5
(0.445–0.453)7.0–7.25
(0.275–0.285)
GENERATOR SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
GeneratorTypeA-Type–J114D(MANDO)–GeneratorTypeA-Type
B-Type–J114D(MANDO)
CS114D(DAC)–
RegulatorA-TypeV14.4–15.0–Regulator
VoltageA-Type
B-TypeV14.4–15.0
14.3–4.9–
Brushes
LengthA-Type
B-Typemm (in.)18.5 (0.728)
20.0 (0.787)13.5 (0.531)
14 (0.551)
OutputA-Type–12V, 65A–Output
(Capacity)A-Type
B-Type–12V, 65A
12V, 65A–
IGNITION SYSTEM SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
Ignition CoilType–Closed
Magnetic Type–
First Coil ResistanceΩ1.2
10%–
Second Coil ResistanceKΩ12.1
15%–
DistributorType–Optical Sensor
Type–
Spark PlugTypeUnlead–BPR5EY-11–
RN9YC4–
WR8DCX–
TypeLead–BPR5EY–
RN9YC–
WR8DC–
Spark PlugGapUnleadmm (in.)1.1 (0.043)–
1.2 (0.047)–
Leadmm (in.)0.8 (0.031)–
Ignition WireIgnition Wire ResistanceKΩ/m2.5–12.0–

1E–42 ENGINE ELECTRICAL
DAEWOO M-150 BL2
BATTERY SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
BatteryType–MF–
CapacityAH35–
Cold Cranking AmpsCCA246–
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Distributor Bolts10–16–89–142
Battery Retainer Clamp–to–Battery Rod Nuts6–8–53–71
Battery Carrier Tray Bolts9–12–80–106
Battery Cable Nuts9–12–80–106
Starter field Connector Nut9–12–80–106
Starter Through–Bolts4–6–35–53
Starter Mounting Bolts55–6541–48–
Starter Solenoid Assembly Screws6–8–53–71
Starter Solenoid Nuts9–12–80–106
Spark Plug20–3015–22–
Generator Through–Bolts4–6–35–53
Generator Drive End Nut80–11 059–81–
Generator Battery Lead Connector Nut4–7–35–62
Generator Bearing Plate Bolt6–8–53–71
Generator Brush Holder / Rectifier Screw9–12–80–106
Generator Belt Tension Adjusting Bolt18–2813–21–
Generator Shackle Bracket Bolt45–5533–41–
Generator Lower Bracket–to–Generator Bolt/Nut18–2813–21–
Ground Bolt35–4126–30–
Ignition Coil Screw4–7–35–62
Ignition Coil Bracket Bolt9–12–80–106

MANUAL TRANSAXLE DRIVE AXLE 3B–7
DAEWOO M-150 BL2
D14B505B
5. Install the control arm ball joint bolt.
Tighten
Tighten the control arm ball joint bolt to 50–70 N
m
(36–52 lb-ft).
a. Control arm ball joint bolt
6. Install the tie rod into the knuckle and install the tie
rod end joint castellated nut.
Tighten
Tighten the tie rod end joint castellated nut to 30–55
N
m (21–41 lb-ft).
b. Tie rod end joint castellated nut.
D14B506A
33–53 N
m
40–50 N
m7. Install the stabilizer bar.Tighten
Tighten the stabilizer bar mounting bolts 33–53
N
m (24–39 lb-ft).
Tighten the stabilizer bar castellated nut to 40–50
N
m (30–36 lb-ft).
a. Stabilizer bar mounting bolt.
b. Stabilizer bar castellated nut.
D14B507A
8. Install the drive axle shaft nut.
Tighten
Tighten the drive axle shaft nut to 210 N
m (155 lb-ft)
Notice: Always use a new nut. Always peen the
caulking nut with a punch and a hammer until the nut
is locked into place on the wheel hub.
9. Install the wheels. Refer to Section 2E, Tires and
wheels.
D13BB520A
10. Refill the transaxle fluid to the proper level.
Tighten the drain plug to 25-30 N
m (18-22 lb-ft)
(a).
Remove the oil level plug (1).
Refill recommended fluid to the proper level.
Tighten the oil level plug to 36-54 N
m (26–40 lb-
ft) (b).
Classification 75W–85 (GL–4) Capacity2.1L (2.21 gt)

3B –12 MANUAL TRANSAXLE DRIVE AXLE
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS

Application

Description

Unit

Standard

Limit
Inner

–Tripot Joint

– Type
Outer

–Rzeppa Joint

–
Right

mm (in.)553.5(21.79)

– Length
Left

mm (in.)386.5(15.22)

– Drive AxleShaft Diameter

mm (in.)22 (0.87)

–


Inner

g (ounce)90 – 100
(3.2 – 3.5)

–


Grease Capacity
Outer

g (ounce)80 – 90
(2.8 – 3.2)
–
FASTENER TIGHTENING SPECIFICATIONS
Application N
m Lb-Ft Lb-In
Control Arm Ball Joint Bolt 50 – 70 36 – 52 –
Tie Rod End Joint castellated Nut 30 – 55 21 – 41 –
Stabilizer Bar Bolt 33 – 53 24 – 39 –
Stabilizer Bar Castellated Nut40 – 5030 – 36–
Drive Axle Shaft Nut 210 155 –
Wheel Nut 90 – 11 0 66 – 81 –
Transaxle Under Cover Bolt35 – 5525 – 41–
Oil Drain Plug25 – 3018 – 22–
Oil Level Plug36 – 5426 – 40–

FIVE-SPEED MANUAL TRANSAXLE 5B–9
DAEWOO M-150 BL2
CHECKING FLUID LEVEL
Check for a leak in the area of transaxle case and seal-
ing and then check fluid level and condition after remov-
ing oil level plug.
1. Operate the engine until it comes to normal operating
temperature(Coolant temperature : 80~90°C (176~
194°F)).
2. Stall the engine and raise the vehicle.
3. Remove the oil level plug and check the fluid level.
4. The fluid should slightly flow out from the oil level plug
hole.
5. If the level is low, add the recommended fluid through
the oil level plug hole until the fluid begins to run out.
6. If the fluid is contaminated or discolored, replace it
with the recommended fluid.
7. Reinstall the oil level plug and tighten it securely.
D103B301
CHANGING FLUID
1. Operate the engine until it comes to normal operating
temperature(Coolant temperature : 80~90°C (176~
194°F)).
2. Stall the engine and raise the vehicle.
3. Drain the fluid after removing the drain plug.
4. Reinstall the drain plug and tighten it securely after
coating sealant.
5. Remove the oil level plug and replenish the fluid until
it begins to run out.
a. Oil drain plug.
b. Oil level plug.
6. Reinstall the oil level plug and tighten it securely.Fluid Specification
75W-85(GL-4)
Fluid Capacity2.1L(2.21qt)
Service intervalRefer to Owner’s Manual
CHECKING TRANSAXLE NOISE
Many noises that appear to come from the transaxle
may actually originate with other sources such as tires,
road surfaces, wheel bearings, or engine and exhaust
system.
Identify the cause of any noise before attempting to re-
pair the clutch, the transaxle, or their related linkages.
To verify suspected transaxle noises,
1. Select a smooth, level asphalt road to reduce tyre
and resonant body noise.
2. Drive the vehicle far enough to warm up all the lubri-
cants thoroughly.
3. Record the speed and the gear range of the transaxle
when the noise occurs.
4. Check for noises with the vehicle stopped, but with
the engine running.
5. Determine if the noise occurs while the vehicle oper-
ates in.

Drive – Under a light acceleration or a heavy pull.

Float – Maintaining a constant speed with a light
throttle on a level road.

Coast – With the transaxle in gear and the throttle
partly or fully closed.

All of the above.
CHECKING BEARING NOISE
Differential Side Bearing Noise
Differential side bearing noise and wheel bearing noise
can be confused easily. Since side bearings are pre-
loaded, a differential side bearing noise should not di-
minish much when the differential/transaxle is run with
the wheels off the ground.
Wheel Bearing Noise
Wheel bearings produce a rough growl or grating sound
that will continue when the vehicle is coasting and the
transaxle is in NEUTRAL. Since wheel bearings are not
pre-loaded, a wheel bearing noise should diminish con-
siderably when the wheels are off the ground.

5B–16 FIVE-SPEED MANUAL TRANSAXLE
DAEWOO M-150 BL2
D13B5032
8. Install the radiator lower hose and crank position
(CKP) sensor.
Tighten
Tighten the radiator lower hose bolt to 8–15 Nm
(70–132 lb-in).
Tighten the CKP sensor bolt to 5–8 Nm (44–70 lb-
in).
D13B520A
9. Refill the transaxle fluid.

Tighten the drain plug to 25–30 Nm (18–22 lb-ft)
(a).

Remove the oil level plug (1).

Refill recommended fluid to the proper level.
Classification 75W – 85 (GL–4) Capacity2.1L (2.21 qt)

Tighten the oil level plug to 36–54 Nm (26–40 lb-ft)
(b).
D13B521A
10. Adjust the clutch cable. Refer to Section 5C, Clutch.

Adjust the clutch cable by the clutch cable adjust
nut.
11. Install the transaxle under cover.
Tighten
Tighten the transaxle under cover bolts to 35–55
Nm (25–41 lb-ft).
D103B501
GEAR SHIFT CONTROL CASE
ASSEMBLY
Removal Procedure
1. Remove the air hose (air cleaner to throttle body).
Refer to Section 1B, SOHC Engine Mechanical.
2. Remove the battery.
3. Disconnect the select and the shift control cable.

Remove the cable pins (1).

Remove the washers (2).

Disconnect the select and the shift control cable
(3).

Remove the cable E–rings (4).

Disconnect the cables from the cable bracket.

6B –8 POWER STEERING PUMP
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS

Application

Description
Lubricant

Power Steering Fluid DEXRON-II, DEXRON-III
Capacity

1.0 Liter (1.056 qt)
Type

Vane
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In
Power Steering Pump Bolt 20 – 24 15 – 18 –
Power Steering Pump Front Bracket Bolt 20 – 24 15 – 18 –
Power Steering Pump Front Bracket Adjusting Bolt 18 – 22 13 – 16 –
Power Steering Pump Rear Bracket Upper Bolt 35 – 45 26 – 33 –
Power Steering Pump Rear Bracket Lower Bolt 20 – 24 15 – 18 –
Power Steering Pump Rear Bracket Adjusting Bolt20 – 2415 – 18–
Power Steering Pump Pulley Nut55 – 6941– 51–
Power Steering Oil Pressure Line Fitting21 – 3516 – 26–

POWER STEERING GEAR 6C–13
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescription
Power Steering FluidPower Steering Fluid DEXRON-II or DEXRON-III
Capacity1.0 L (1.056 qt)
TypeRack and Pinion
Overall Gear Ratio15.7 : 1
Power Steering Angle144, 155Inside39.5± 2
TireOutside33.5± 2
175 TireInside34.9± 2
Outside30.5± 2
GreaseRackPOLYUREAS
Ball JointSYNTHETICS OILS & LI SOAPS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Power Steering Gear Bracket Bolt50–5536–41–
Power Steering Gear Pinion Nut40–5030–36–
Power Steering Gear Pinion Dust Cover45–5533–41–
Power Steering Gear Pressure Line Fitting25–3518–25–
Power Steering Oil Pressure Pipe Fitting (Gear Side)21–3516–25–
Power Steering Gear Ajuster PlugRefer to “DIAGNOSIS” in this section.