battery replacement DODGE CALIBER 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2010, Model line: CALIBER, Model: DODGE CALIBER 2010 1.GPages: 484, PDF Size: 6.43 MB
Page 11 of 484
▫Sound Horn With Remote Key Lock ........ 21
▫ Flash Lights With Remote Key Lock/Unlock . . 22
▫ Using The Panic Alarm ................. 22
▫ Programming Additional Transmitters ...... 23
▫ General Information ................... 23
▫ Transmitter Battery Replacement .......... 24
Remote Starting System — If Equipped ....... 25
▫ How To Use Remote Start ............... 25
Door Locks ........................... 27
▫ Manual Door Locks ................... 27
▫ Power Door Locks .................... 28
▫ Child-Protection Door Lock System (Rear
Doors) — If Equipped .................. 31
Power Windows — If Equipped ............ 33
▫ Power Window Switches ................ 33
▫ Auto-Down ......................... 34
▫ Window Lockout Switch ................ 35
Liftgate ............................. 35
Occupant Restraints ..................... 37
▫ Lap/Shoulder Belts .................... 39
▫ Adjustable Upper Shoulder Belt Anchorage . . . 44
▫ Lap/ Shoulder Belt Operating Instructions
With A Mini-Latch And Buckle ............ 45
▫ Lap/Shoulder Belt Untwisting Procedure .... 48
▫ Automatic Locking Retractors (ALR) Mode
— If Equipped ....................... 48
▫ Seat Belts In Passenger Seating Positions ..... 49
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 25 of 484
Transmitter Battery Replacement
NOTE:Perchlorate Material – special handling may apply.
See “www.dtsc.ca.gov/hazardouswaste/perchlorate.”
The recommended replacement battery is CR2032.
1. If the RKE transmitter is equipped with a screw,
remove the screw. With the RKE transmitter buttons
facing down, use a flat blade to pry the two halves of the
RKE transmitter apart. Make sure not to damage the
elastomer seal during removal.
2. Remove and replace the battery. Avoid touching the
new battery with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.
3. To reassemble the RKE transmitter case, snap the two
halves together.
NOTE:If the RKE transmitter is equipped with a screw,
reinstall and tighten the screw until snug.
Separating Case Halves
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 390 of 484
MAINTAINING YOUR VEHICLE
CONTENTS
Engine Compartment — 2.0L ............. 391
Engine Compartment — 2.4L ............. 392
Onboard Diagnostic System — OBD II ...... 393
▫ Loose Fuel Filler Cap Message ........... 393
Emissions Inspection And Maintenance
Programs ............................ 394
Replacement Parts ..................... 395
Dealer Service ........................ 395
Maintenance Procedures ................. 396 ▫
Engine Oil ......................... 397
▫ Engine Oil Filter ..................... 400
▫ Engine Air Cleaner Filter ............... 400
▫ Maintenance-Free Battery .............. 401
▫ Air Conditioner Maintenance ............ 402
▫ Body Lubrication .................... 403
▫ Windshield Wiper Blades ............... 404
▫ Adding Washer Fluid ................. 404
▫ Exhaust System ..................... 405
7
Page 396 of 484
4. Approximately 15 seconds later, one of two things will
happen:a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn OFF
the ignition or start the engine. This means that your
vehicle’s OBD II system is not readyand you should
not proceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn OFF the ignition or start the
engine. This means that your vehicle’s OBD II system
is ready and you can proceed to the I/M station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD II
system to update. A recheck with the above test routine
may then indicate that the system is now ready. Regardless of whether your vehicle’s OBD II system is
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
before going to the I/M station. The I/M station can fail
your vehicle because the MIL is on with the engine
running.
REPLACEMENT PARTS
Use of genuine MOPAR
parts for normal/scheduled
maintenance and repairs is highly recommended to en-
sure the designed performance. Damage or failures
caused by the use of non-MOPAR parts for maintenance
and repairs will not be covered by the manufacturer’s
warranty.
DEALER SERVICE
Your authorized dealer has the qualified service person-
nel, special tools, and equipment to perform all service
operations in an expert manner. Service Manuals are
available which include detailed service information for
7
MAINTAINING YOUR VEHICLE 395
Page 428 of 484
VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days, you may want to take steps to preserve your
battery.
•Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
•Disconnect the negative cable from the battery.
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS – Interior Bulb Number
Front Header Lamp...................... T578
Center Dome Lamp ...................... T578
Rear Cargo/Flashlight ................. 8–A35LFLIGHTS BULBS – Exterior
Bulb Number
Low Beam/High Beam Headlamp ............ H13
Front Park/Turn Signal/Side Marker Lamp . . . 3157AK
Front Fog Lamp ...................... PSX24W
Center High-Mounted Stop Lamp
(CHMSL) ...................... LED Assembly
Rear Tail/Stop Lamp ..................... 3157
Rear Turn Signal Lamp .................3757AK
Backup Lamp ...................... 921 W16W
License Lamp .......................... W5W
BULB REPLACEMENT
Front Headlamps, Parking, and Turn Signal
Lamps
NOTE:The headlamp bulb can be accessed from under
the hood without the removal of the inner fender well. It
will be necessary to remove the inner fender well to
service the park/turn signal bulb that is located toward
the outboard side of the head lamp unit.
7
MAINTAINING YOUR VEHICLE 427
Page 468 of 484
Overheating.......................... 373
Selection Of Lubricant ................... 416
Shifting ............................. 300
Special Additives ...................... 416
Autostick ............................. 302
Battery ............................... 401
Keyless Transmitter Replacement (RKE) ....... 24
Belts, Seat .............................. 87
Beverage Cooler ........................ 175
Body Mechanism Lubrication ............... 403
B-Pillar Location ........................ 326
Brake Assist System ...................... 314
Brake Fluid ............................ 435
Brake, Parking .......................... 308
Brake System ........................ 310,413
Anti-Lock (ABS) .................... 31 1,314
Master Cylinder ....................... 413
Parking ............................. 308 Warning Light
........................ 195
Brakes ............................. 310,413
Brake/Transmission Interlock ............... 299
Break-In Recommendations, New Vehicle ........ 84
Bulb Replacement ....................... 427
Bulbs, Light .......................... 89,427
Capacities, Antifreeze (Engine Coolant) ........ 433
Capacities, Fluid ........................ 433
Caps, Filler Fuel ............................... 353
Oil (Engine) ....................... 392,399
Power Steering ........................ 307
Car Washes ............................ 418
Carbon Monoxide Warning ...............86,352
Cargo Area Cover ....................... 179
Cargo Area Features ...................... 178
Cargo Compartment Light ............................... 178
10
INDEX 467