bulb DODGE CALIBER 2012 1.G User Guide

▫Cooling System ..................... 430
▫ Brake System ....................... 435
▫ Automatic Transmission (CVT) –
If Equipped ........................ 438
▫ Manual Transmission – If Equipped ....... 439
▫ Appearance Care And Protection From
Corrosion .......................... 439
 Fuses .............................. 445
▫ Integrated Power Module .............. 445
 Vehicle Storage ....................... 449
 Replacement Bulbs .................... 449
 Bulb Replacement ..................... 450 ▫
Front Headlamps, Parking, And Turn Signal
Lamps ............................ 450
▫ Fog Lamps ......................... 450
▫ Rear Tail, Turn Signal, And Backup Lamps . . 451
▫ License Lamps ...................... 453
▫ Center High-Mounted Stoplamp ......... 454
 Fluid Capacities ...................... 455
 Fluids, Lubricants, And Genuine Parts ....... 456
▫ Engine ............................ 456
▫ Chassis ........................... 457
412 MAINTAINING YOUR VEHICLE

persists, the message will appear the next time the
vehicle is started. This might indicate a damaged cap. If
the problem is detected twice in a row, the system will
turn on the MIL. Resolving the problem will turn the MIL
light off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing. Normally, the OBD II system will be ready. The OBD II
system may
notbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over.
3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
416 MAINTAINING YOUR VEHICLE

VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days, you may want to take steps to preserve your
battery.
•Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
•Or disconnect the negative cable from the battery.
•Anytime you store your vehicle, or keep it out of
service (i.e., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS – Interior Bulb Number
Front Header Lamp...................... T578
Center Dome Lamp ...................... T578
Rear Cargo/Flashlight ................. 8–A35LF
LIGHTS BULBS – Exterior Bulb Number
Low Beam/High Beam Headlamp ............ H13
Front Park/Turn Signal/Side Marker Lamp . . . 3157AK
Front Fog Lamp ...................... PSX24W
Center High-Mounted Stop Lamp
(CHMSL) ...................... LED Assembly
Rear Tail/Stop Lamp ..................... 3157
Rear Turn Signal Lamp .................3757AK
Backup Lamp ...................... 921 W16W
License Lamp .......................... W5W
7
MAINTAINING YOUR VEHICLE 449

BULB REPLACEMENT
Front Headlamps, Parking, and Turn Signal
Lamps
NOTE:The headlamp bulb can be accessed from under
the hood without the removal of the inner fender well. It
will be necessary to remove the inner fender well to
service the park/turn signal bulb that is located toward
the outboard side of the head lamp unit.
1. Disconnect and isolate the negative battery cable.
2. Working in the appropriate wheel well, loosen the
front of the splash shield, but do not fully remove it.
3. Looking up through the front wheel well, locate the
bulb which needs replacing. The headlamp bulb is the
inboard bulb and the park/turn signal bulb is the out-
board bulb.
4. Disconnect the bulb electrical connector. 5. Grasp the bulb, twist 1/4 turn counterclockwise and
pull straight out of front lamp unit.
Fog Lamps
CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
1. Disconnect and isolate the negative battery cable.
2. Remove the front wheel and tire on the same side of
the vehicle as the fog lamp being serviced. Refer to
“Jacking and Tire Changing” in “What To Do In Emer-
gencies” for further information.
3. Remove the three screws that secure the outboard side
of the front wheel house splash shield to the front fascia.
450 MAINTAINING YOUR VEHICLE

4. Remove the push pin fastener that secures the inboard
side of the splash shield to the front end sheet metal.
5. Remove the two push pin fasteners that secure the
forward edge of the splash shield to the front fascia
closure panel.
6. Fold the front of the splash shield rearward far enough
to access the back of the front fascia.
7. From behind the front fascia disconnect the engine
compartment wire harness connector from the front fog
lamp bulb connector receptacle.
8. Firmly grasp the bulb by the two latch features and
squeeze them together to unlock the bulb from the back
of the front fog lamp housing.
9. Pull the bulb straight out from the keyed opening in
the housing.Rear Tail, Turn Signal, and Backup Lamps
1. Remove the two push-pins from the tail lamp housing.
7
MAINTAINING YOUR VEHICLE 451

2. Grasp the tail lamp and pull firmly to disengage the
lamp from the aperture panel.
NOTE:It is not necessary to completely remove the tail
lamp unit. Once loosened from the quarter panel, there
should be enough room to service any of the bulbs. 3. Disconnect the electrical connector from the bulb.
4. Twist and remove socket from the lamp.
452 MAINTAINING YOUR VEHICLE

5. Remove the bulb from the socket and replace.License Lamps
1. Using a trim stick or equivalent, gently pry on the side
of the license plate lamp to release it from the liftgate.
7
MAINTAINING YOUR VEHICLE 453

2. Rotate the socket 1/4 turn counterclockwise and re-
move from the lamp.3. Pull the bulb from the socket.
Center High-Mounted Stoplamp
The lamp is an LED assembly. See your authorized dealer
for replacement.
454 MAINTAINING YOUR VEHICLE

Fluid and Filter Changes............... 439
Fluid Level Check .................... 438
Fluid Type ......................... 438
Gear Ranges ........................ 307
Special Additives ..................... 438
Autostick ............................. 312
B-Pillar Location ........................ 337
Battery ............................... 423
Keyless Transmitter Replacement (RKE) ..... 25
Belts, Seat .............................. 89
Beverage Cooler ........................ 192
Body Mechanism Lubrication ............... 425
Brake Assist System ...................... 325
Brake Fluid ............................ 457
Brake System ........................ 321,435
Anti-Lock (ABS) .................. 322,325
Master Cylinder ..................... 435
Parking ........................... 319 Warning Light
....................... 204
Brake, Parking .......................... 319
Brake/Transmission Interlock ............... 306
Brakes ............................. 321,435
Break-In Recommendations, New Vehicle ........ 86
Bulb Replacement ..................... 449,450
Bulbs, Light .......................... 91,449
Capacities, Antifreeze (Engine Coolant) ........ 455
Capacities, Fluid ........................ 455
Caps, Filler Fuel .............................. 367
Oil (Engine) ................... 413,414,421
Power Steering ...................... 318
Car Washes ............................ 440
Carbon Monoxide Warning ...............88,367
Cargo Area Cover ....................... 187
Cargo Area Features ...................... 185
10
INDEX 487

Liftgate (Sedan).......................... 37
Liftgate Window Wiper/Washer ............. 190
Light Bulbs .......................... 91,449
Lights .............................. 91,152
Airbag ...................... 69,75,89,203
Alarm ............................ 210
Anti-Lock .......................... 213
Back-Up ........................... 451
Brake Assist Warning .................. 330
Brake Warning ...................... 204
Bulb Replacement .................... 450
Cargo ............................. 185
Center Mounted Stop .................. 454
Dimmer Switch, Headlight .............. 152
Electronic Stability Program (ESP) Indicator . . 330
Engine Temperature Warning ............ 203
Exterior ............................ 91
Fog ......................... 154,210,450
Headlight Switch ..................... 153 Headlights
......................... 153
High Beam Indicator .................. 214
Instrument Cluster ................... 153
License ............................ 453
Lights On Reminder .................. 154
Low Fuel .......................... 202
Malfunction Indicator (Check Engine) ...... 212
Map Reading ....................... 157
Oil Pressure ........................ 203
Seat Belt Reminder ................... 203
Security Alarm (Theft Alarm) ..........18,210
Service Engine Soon (Malfunction
Indicator) .......................... 212
Theft Alarm (Security Alarm) ............ 210
Tire Pressure Monitoring (TPMS) ......... 211
Traction Control ..................... 330
Turn Signal ................. 91,152,155,451
Voltage ............................ 202
Warning (Instrument Cluster Description) . . . 201
494 INDEX