tire type DODGE CHALLENGER 2018 Vehicle Warranty
[x] Cancel search | Manufacturer: DODGE, Model Year: 2018, Model line: CHALLENGER, Model: DODGE CHALLENGER 2018Pages: 316, PDF Size: 3.15 MB
Page 14 of 316
Fuel Economy
Underinflated tires will increase tire rolling resistance resulting in higher
fuel consumption.
Tread Wear
Improper cold tire inflation pressures can cause abnormal wear patterns
and reduced tread life, resulting in the need for earlier tire replacement.
Ride Comfort And Vehicle Stability
Proper tire inflation contributes to a comfortable ride. Over-inflation
produces a jarring and uncomfortable ride.
Tire Inflation Pressures
The proper cold tire inflation pressure is listed on the driver’s side
B-Pillar or rear edge of the driver’s side door.
At least once a month:
•Check and adjust tire pressure with a good quality pocket-type
pressure gauge. Do not make a visual judgement when determining
proper inflation. Tires may look properly inflated even when they are
under-inflated.
•Inspect tires for signs of tire wear or visible damage.
CAUTION!
After inspecting or adjusting the tire pressure, always reinstall the
valve stem cap. This will prevent moisture and dirt from entering the
valve stem, which could damage the valve stem.
Inflation pressures specified on the placard are always “cold tire inflation
pressure”. Cold tire inflation pressure is defined as the tire pressure after
the vehicle has not been driven for at least three hours, or driven less than
1 mile (1.6 km) after sitting for a minimum of three hours. The cold tire
inflation pressure must not exceed the maximum inflation pressure
molded into the tire sidewall.
Check tire pressures more often if subject to a wide range of outdoor
temperatures, as tire pressures vary with temperature changes.
Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air
temperature change. Keep this in mind when checking tire pressure
inside a garage, especially in the Winter.
TIRES
13
Page 15 of 316
Example: If garage temperature = 68°F (20°C) and the outside tempera-
ture = 32°F (0°C) then the cold tire inflation pressure should be increased
by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this
outside temperature condition.
Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation.
DO NOT reduce this normal pressure build up or your tire pressure will
be too low.
Tire Pressures For High Speed Operation
The manufacturer advocates driving at safe speeds and within posted
speed limits. Where speed limits or conditions are such that the vehicle
can be driven at high speeds, maintaining correct tire inflation pressure is
very important. Increased tire pressure and reduced vehicle loading may
be required for high-speed vehicle operation. Refer to an authorized tire
dealer or original equipment vehicle dealer for recommended safe
operating speeds, loading and cold tire inflation pressures.
WARNING!
High speed driving with your vehicle under maximum load is
dangerous. The added strain on your tires could cause them to fail.
You could have a serious collision. Do not drive a vehicle loaded to
the maximum capacity at continuous speeds above 75 mph
(120 km/h).
Radial Ply Tires
WARNING!
Combining radial ply tires with other types of tires on your vehicle
will cause your vehicle to handle poorly. The instability could cause
a collision. Always use radial ply tires in sets of four. Never combine
them with other types of tires.
TIRES
14
Page 20 of 316
Tire Types
All Season Tires — If Equipped
All Season tires provide traction for all seasons (Spring, Summer, Fall, and
Winter). Traction levels may vary between different all season tires. All
season tires can be identified by the M+S, M&S, M/S or MS designation on
the tire sidewall. Use all season tires only in sets of four; failure to do so may
adversely affect the safety and handling of your vehicle.
Summer Or Three Season Tires — If Equipped
Summer tires provide traction in both wet and dry conditions, and are
not intended to be driven in snow or on ice. If your vehicle is equipped
with Summer tires, be aware these tires are not designed for Winter or
cold driving conditions. Install Winter tires on your vehicle when
ambient temperatures are less than 40°F (5°C) or if roads are covered with
ice or snow. For more information, contact an authorized dealer.
Summer tires do not contain the all season designation or mountain/
snowflake symbol on the tire sidewall. Use Summer tires only in sets of
four; failure to do so may adversely affect the safety and handling of your
vehicle.
WARNING!
Do not use Summer tires in snow/ice conditions. You could lose
vehicle control, resulting in severe injury or death. Driving too fast
for conditions also creates the possibility of loss of vehicle control.
Snow Tires
Some areas of the country require the use of snow tires during the Winter.
Snow tires can be identified by a “mountain/snowflake” symbol on the
tire sidewall.
If you need snow tires, select tires equivalent in size
and type to the original equipment tires. Use snow
tires only in sets of four; failure to do so may adversely
affect the safety and handling of your vehicle.
Snow tires generally have lower speed ratings than
what was originally equipped with your vehicle and
should not be operated at sustained speeds over 75 mph (120 km/h). For
speeds above 75 mph (120 km/h) refer to original equipment or an
TIRES
19
Page 21 of 316
authorized tire dealer for recommended safe operating speeds, loading
and cold tire inflation pressures.
While studded tires improve performance on ice, skid and traction
capability on wet or dry surfaces may be poorer than that of non-studded
tires. Some states prohibit studded tires; therefore, local laws should be
checked before using these tire types.
Spare Tires — If Equipped
NOTE:For vehicles equipped with Tire Service Kit instead of a spare tire,
please refer to “Tire Service Kit” in “In Case Of Emergency” in your
Owner ’s Manual for further information.
CAUTION!
Because of the reduced ground clearance, do not take your vehicle
through an automatic car wash with a compact or limited use
temporary spare installed. Damage to the vehicle may result.
Spare Tire Matching Original Equipped Tire And Wheel — If
Equipped
Your vehicle may be equipped with a spare tire and wheel equivalent in
look and function to the original equipment tire and wheel found on the
front or rear axle of your vehicle. This spare tire may be used in the tire
rotation for your vehicle. If your vehicle has this option, refer to an
authorized tire dealer for the recommended tire rotation pattern.
Compact Spare Tire — If Equipped
The compact spare is for temporary emergency use only. You can identify
if your vehicle is equipped with a compact spare by looking at the spare
tire description on the Tire and Loading Information Placard located on
the driver ’s side door opening or on the sidewall of the tire. Compact
spare tire descriptions begin with the letter “T” or “S” preceding the size
designation. Example: T145/80D18 103M.
T, S = Temporary Spare Tire
Since this tire has limited tread life, the original equipment tire should be
repaired (or replaced) and reinstalled on your vehicle at the first
opportunity.
Do not install a wheel cover or attempt to mount a conventional tire on
the compact spare wheel, since the wheel is designed specifically for the
TIRES
20
Page 32 of 316
DRIVING ON ANY TIRE THAT DOES NOT HAVE THE CORRECT
INFLATION PRESSURE IS DANGEROUS
Any underinflated tire builds up excessive heat that may result in sudden
tire destruction. If tires are supplied as original equipment, refer to the
tire decal on the vehicle (check vehicle and/or vehicle owner ’s manual
for decal location) for the recommended operating pressures. For replace-
ment tires, the correct inflation pressure will be provided by your tire
retailer; if not, refer to the vehicle decal.
These inflation pressures must be maintained as a minimum. However,
do not exceed the maximum pressure rating indicated on the tire
sidewall.
CHECK THE COLD INFLATION PRESSURES IN ALL YOUR TIRES,
INCLUDING THE SPARE, AT LEAST ONCE EACH MONTH
Failure to maintain correct inflation may result in improper vehicle
handling and may cause rapid and irregular tire wear, sudden tire
destruction, loss of vehicle control and serious personal injury. Therefore,
inflation pressures should be checked at least once each month and
always prior to long distance trips. This applies to all tires, including
sealant types, and Self-Supporting tires which are as susceptible to losing
air pressure as any other type of tire if not properly maintained.
UNDERINFLATION
It is impossible to determine whether tires are properly inflated by
simply looking at them. It is almost impossible to “feel or hear” when a
tire is being run underinflated or nearly flat. Tires must be checked
monthly with a tire pressure gauge.
Pressures should be checked when tires are cold, in other words, before
they have been driven on. Driving, even for a short distance, causes tires
to heat up and air pressure to increase.
Checking pressure when tires are hot:
If pressures are checked after tires have been driven for more than three
minutes or more than one mile, (1.6 km) the tires become hot and the
pressures will increase by approximately 4 psi. Therefore when the tire
pressure is adjusted under these conditions, it should be increased to a
gauge reading of 4 psi greater than the recommended cold inflation
pressure.
BFGOODRICH TIRES
31
Page 34 of 316
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop.
If you see any damage to a tire or wheel, replace it with the spare at
once and visit a participating BFGoodrich Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of BFGoodrich tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
BFGOODRICH TIRES
33
Page 38 of 316
The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any BFGoodrich® tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES CHECK
HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
BFGoodrich® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s Owner‘s Manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
BFGOODRICH TIRES
37
Page 40 of 316
FULL-SIZE SPARE
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
REPLACEMENT OF TWO (2) TIRES
It is recommended that all four (4) tires are replaced at the same time.
However, whenever only two tires are replaced, the new ones should be
put on the rear. The new tires, with deeper tread, may provide better grip
and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
avoid sudden, sharp turns or lane changes and obey all traffic laws.
Failure to do so may result in loss of vehicle control leading to an accident
and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires.
Alterations may prevent proper performance, leading to tire damage
which can result in an accident. Tires which become unserviceable due to
alterations such as trueing, whitewall inlays, addition of balancing or
sealant liquids, or the use of tire dressing containing petroleum distillates
are excluded from warranty coverage.
BFGOODRICH TIRES
39
Page 41 of 316
REPAIRS - WHEREVER POSSIBLE, SEE YOUR BFGOODRICH®
TIRE RETAILER AT ONCE
If any BFGoodrich® tire sustains a puncture, have the tire demounted
and thoroughly inspected by any BFGoodrich® tire retailer for possible
damage that may have occurred.
A tread area puncture in any BFGoodrich® passenger or light truck tire
can be repaired provided that the puncture hole is not more than 1/4” in
diameter, not more than one radial cable per casing ply is damaged, and
the tire has not been damaged further by the puncturing object or by
running underinflated. Tire punctures consistent with these guidelines
can be repaired by following the Rubber Manufacturers Association
(RMA) recommended repair procedures.
TIRE REPAIRS
Repairs of all tires must be of the combined plug and inside patch type.
Plug only repairs are improper.A tire should be removed from the rim
and inspected prior to repair. Any tire repair done without removing the
tire from the rim is improper. An improperly repaired tire will cause
further damage to the tire by either leaking air or allowing air, moisture
and contaminants to enter the structure of the tire. An improperly
repaired tire can fail suddenly at a later date.
Never repair a tire with less than 2/32 nds of an inch tread remaining. At
this tread depth, the tire is worn out and must be replaced.
TEMPORARY SPARE TIRES
When using any temporary spare tire, be sure to follow the vehicle
manufacturer ’s instructions.
READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
DOT XXXX XXXX XXX (1990-1999)
DOT XXXX XXXX XXXX (after July 2000)
THE DOT
The “DOT” symbol certifies tire manufacturer ’s compliance with U.S.
Department of Transportation tire safety standards. Next to the symbol is
the tire identification or “serial number”. The first two characters identify
the plant where the tire was manufactured. The next two characters
BFGOODRICH TIRES
40
Page 42 of 316
reflect the tire size. The following one to four digits may be used at the
tire manufacturer ’s option as a descriptive code. The last three characters
are numbers identifying the week and year of manufacture. (Example:
“O25” means second week of the year of decade, eg.: 1995, 1985, etc.)
Tires produced after July 2000 have an additional digit to identify a given
decade. For example, 2800 means the tire was produced during the 28th
week of 2000; 0201 during the 2nd week of 2001. If the last digits of your
DOT number contain three numeric characters consult a qualified tire
technician to determine the year and decade of manufacture.
STORAGE
Tires contain waxes and emollients to protect their outer surfaces from
ozone and weather checking. As the tire rolls and flexes, the waxes and
emollients continually migrate to the surface, replenishing this protection
throughout the normal use of the tire. Consequently, when tires sit
outdoors, unused for long periods of time (a month or more) their
surfaces become dry and more susceptible to ozone and weather check-
ing and the casing becomes susceptible to flat spotting.
For this reason, tires should always be stored in a cool, dry, clean,
indoor environment. If storage is for one month or more, eliminate the
weight from the tires by raising the vehicle or by removing the tires
from the vehicle. Failure to store tires in accordance with these
instructions could result in damage to your tires or premature aging of
the tires and sudden tire failure.
When tires are stored, be sure they are placed away from sources of heat
and ozone such as hot pipes and electric generators. Be sure that surfaces
on which tires are stored are clean and free from grease, gasoline or other
substances which could deteriorate the rubber.(Tires exposed to these
materials during storage or driving could be subject to sudden failure.)
FOLLOW THESE MOUNTING RECOMMENDATIONS
Tire changing can be dangerous and must be done by professionally
trained persons using proper tools and procedures as specified by the
Rubber Manufacturers Association (RMA).
Your tires should be mounted on wheels of correct size and type and
which are in good, clean condition. Wheels that are bent, chipped, rusted
(steel wheels) or corroded (alloy wheels) may cause tire damage. The
inside of the tire must be free from foreign material. Have your retailer
check the wheels before mounting new tires. Mismatched tires and rims
BFGOODRICH TIRES
41