tyre pressure DODGE CHALLENGER 2022 Vehicle Warranty

GOODYEAR® DUNLOP® TIRES
99
DO NOT MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE SAME AXLE
For optimum handling and control, Goodyear® recommends fitment of four tires of the
same type and size unless otherwise specified by the vehicle manufacturer.
When replacing tires, you must maintain the outside diameter and load-carrying capacity
of
the Original Equipment tire. Inflation pressure may need to be adjusted to avoid
overloading the tire. Consult the Tire & Rim Association Load and Inflation Tables,
European Tire and Rim Technical Organization (ETRTO) or Japan Automobile Tyre
Manufacturers Association (JATMA) standards for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-CARRYING CAPACITY THAN
RE
QUIRED BY THE ORIGINAL EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load Range E tires as
d e

signated by the vehicle manufacturer. Fitment of a tire, such as a Load Range D, with
less carrying capacity is not allowed. In other cases, tires of the same size may carry
different load indexes in the service description. You must make certain the replacement
tires fitted to the vehicle have a load-carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.
NOTE:
Goodyear® manufactured and/or marketed European- Metric passenger tires and
P -

Metric passenger tires are interchangeable as long as they have the same section
width, same aspect ratio, same rim diameter.
FOLLOW THESE ADDITIONAL GUIDELINES
When installing only two tires, fit the tires with the deepest tread depth on the rear axle.
If radials and non-radials must be fitted to the same vehicle, fit radials on rear axle. Never
mix radials and non-radials on the same axle. When fitting winter tires or all-season tires
WARNING!


Before you replace your tires, always consult the vehicle owner’s manual and follow
the vehicle manufacturer’s replacement tire recommendations. Vehicle handling may
be significantly affected by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional installer in order to
make certain that proper clearance, load-carrying capacity and inflation pressure are
selected. Never exceed the maximum load capacity and inflation pressure listed on
the sidewall of the tire. Always drive safely and obey all traffic laws. Avoid sudden,
sharp turns or aggressive lane changes. Failure to follow this warning may result in
loss of control of the vehicle, leading to an accident and serious injury or death.
CAUTION!


Never substitute a “Standard Load” (SL) tire for an Extra Load (XL) or Reinforced tire. If
the vehicle was originally equipped with “Extra Load” (XL) or Reinforced tires, replace
those tires with similar-sized Extra Load (XL) or Reinforced tires.

PIRELLI TIRES
161
PIRELLI TIRE DOES NOT ENDORSE:
• T he use of tire sealants in Pirelli tires to repair, even temporarily, a puncture
•
The repairing of V, W, Y or Z Speed Rated tires
•
The repairing of Run Flat tires
12. Storage
Should you need to store tires after removal from a vehicle (as in the case of winter tires),
they should be stored in a cool, dry place. To protect your tires from damage related to:
heat, water, ozone and direct sunlight, it is suggested you place them in opaque,
waterproof containers (e.g., plastic trash bags).
13. Tubes in Tubeless Tires
Under no circumstances are tubes to be used in Pirelli tires marked “Tubeless”. This
includes tires that have been repaired. If the tire’s pressure retention ability has been
affected, so as to necessitate a tube being installed, the tire must be replaced.
14. Tire Valves
Whenever new tires are installed on your wheels, new tire valves of the correct type must
be installed. During your routine tire inspection, verify that all your valves have proper
valve caps. Replace as necessary, since the valve cap is also a seal against pressure
loss.
15. Tire Demounting and Mounting
Tire fitting is best left to professionals who have the proper tools and equipment to
perform the task properly and safely. Your tires should be mounted or demounted, using
Tire and Rubber Association of Canada procedures or the vehicle manufacturers’
recommendations. Your wheels should be in good, clean condition. Wheels should be
inspected for distortion, dents, cracks, rust and foreign matter, and be replaced as
necessary. NEVER EXCEED 40 PSI WHEN SEATING BEADS.
16. Tire/Wheel Alignment and Balancing
Tire/Wheel alignment specifications are issued by your vehicle manufacturer and your
vehicle must be kept within these tolerances. You should have your alignment checked
annually or whenever you notice any irregular wear or vibrations. Tire/Wheel assemblies
should be balanced each time a tire is fitted to a wheel. Tire/Wheel alignment and
balancing are important for safety and maximum performance and mileage from your
tires.
For more information or service regarding Pirelli tires, please contact your nearest
A u

thorized Pirelli Dealer. To locate an authorized Pirelli Dealer in your area, refer to the
Dealer Locator section on the Pirelli web site at www.ca.pirelli.com.
P ZERO, P ZERO CORSA, P ZERO ROSSO, P ZERO NERO, CINTURATO, SCORPION,
S C

ORPION ZERO, SCORPION VERDE, P3000, P1, P4, P5, P6, P7 are trademarks of Pirelli
Tyre S.p.A.
“Confidence Program” is a trademark of Pirelli Tire Inc.