lock DODGE CHARGER SRT 2010 7.G Owners Manual

TOWING A DISABLED VEHICLE
Without The Ignition Key
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. The only ap-
proved method of towing without the ignition key is
with a flatbed truck. Proper towing equipment is neces-
sary to prevent damage to the vehicle.
Towing This Vehicle Behind Another Vehicle
Flatbed towing is recommended. DO NOT tow an AWD
vehicle with the rear wheels on the ground unless the
rear driveshaft is removed and the transmission is in
NEUTRAL.
Vehicles WITHOUT AWD may be towed (with rear
wheels on the ground) with the transmission in NEU-
TRAL under the following conditions:
•The distance to be traveled must not exceed 15 miles
(24 km).
•The towing speed must not exceed 30 mph (48 km/h).
CAUTION!
Exceeding these towing limits may cause severe
transmission damage. Such damage is not covered by
the New Vehicle Limited Warranty.
Vehicles equipped with AWD can be towed with the
transmission in NEUTRAL and the rear wheels OFF the
ground (or the rear driveshaft removed) with no limita-
tion on speed or distance.
CAUTION!
•Do not attempt to tow this vehicle from the front
with sling-type towing equipment. Damage to the
front fascia will result. (Continued)
6
WHAT TO DO IN EMERGENCIES 327

3. Install the new filter with arrows pointing in the
direction of airflow, which is toward the rear of the
vehicle (text and arrows on the filter will indicate this).Refer to “Maintenance Schedule” for the proper mainte-
nance intervals.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
A/C Air Filter
7
MAINTAINING YOUR VEHICLE 343

tailgate, sliding doors and hood hinges, should be lubri-
cated periodically with a lithium based grease, such as
MOPARSpray White Lube or equivalent to assure
quiet, easy operation and to protect against rust and
wear. Prior to the application of any lubricant, the parts
concerned should be wiped clean to remove dust and
grit; after lubricating excess oil and grease should be
removed. Particular attention should also be given to
hood latching components to ensure proper function.
When performing other underhood services, the hood
latch, release mechanism and safety catch should be
cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant, such as MOPAR 
Lock Cylinder Lubricant or equivalent directly into the
lock cylinder.Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild nonabrasive cleaner. This will remove accumula-
tions of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
NOTE: Life expectancy of wiper blades varies depend-
ing on geographical area and frequency of use. Poor
performance of blades may be present with chattering,
marks, water lines or wet spots. If any condition is
344 MAINTAINING YOUR VEHICLE

To minimize the possibility of catalyst damage:
•Do not shut off the engine or interrupt the ignition
when the transmission is in gear and the vehicle is in
motion.
•Do not try to start the engine by pushing or towing the
vehicle.
•Do not idle the engine with any spark plug wires
disconnected or removed, such as when diagnostic
testing, or for prolonged periods during very rough
idling or malfunctioning operating conditions.
Cooling System
WARNING!
•When working near the radiator cooling fan, dis-
connect the fan motor lead or turn the ignition
switch to the LOCK position. The fan is tempera-
ture controlled and can start at any time the
ignition switch is in the ON position.
•You or others can be badly burned by hot engine
coolant (antifreeze) or steam from your radiator. If
you see or hear steam coming from under the
hood, do not open the hood until the radiator has
had time to cool. Never try to open a cooling
system pressure cap when the radiator is hot.
348 MAINTAINING YOUR VEHICLE

Cavity Car-tridge
FuseMini-
Fuse
Description
1 — 15 Amp BlueWasher Motor
2 — 25 Amp NaturalPowertrain Control
Module (PCM)
3 — 25 Amp NaturalIgnition Run/Start
4 — 25 Amp NaturalAlternator
5 ———
6 — 25 Amp NaturalIgnition Coils/Injectors
7 ———
8 — 30 Amp GreenStarter
9 ———Cavity Car- tridge
FuseMini-
Fuse
Description
10 30 Amp Pink— Windshield Wiper
11 30 Amp Pink— Anti-Lock Brake System
(ABS) Valves
12 40 Amp Green— Radiator Fan
13 50 Amp Red— Anti-Lock Brake System
(ABS) Pump Motor
14———
15 50 Amp Red— Radiator Fan
16———
17———
18———
19———
7
MAINTAINING YOUR VEHICLE 365

BULB REPLACEMENT
Low Beam Headlamp, High Beam Headlamp,
Park/Turn Lamp, and Front Side Marker Lamp —
Models with Halogen Headlamps
1. Open the hood.
NOTE:Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs in the headlamp
assembly on the driver side of the vehicle.
2.
Twist the appropriate bulb and socket assembly counter-
clockwise, and then pull it out of the headlamp assembly.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol. 3. Disconnect the bulb from the socket assembly and
install the replacement bulb.
4. Reinstall the bulb and socket assembly into the head-
lamp assembly, and then turn it clockwise.
1 — High Beam Headlamp Bulb
2 — Low Beam Headlamp Bulb
7
MAINTAINING YOUR VEHICLE 373

2. Remove two fasteners from the back of the taillamp
assembly.
3. Pull back the trunk liner.
4. Remove the remaining fastener from the back of the
taillamp assembly.
5. Push the electrical connector locking tab to the side.6. Disconnect the electrical connector.
7. Pull the taillamp assembly clear from the vehicle to
access the bulbs.
8. Turn the appropriate bulb and socket assembly coun-
terclockwise to remove it from the taillamp assembly.
376 MAINTAINING YOUR VEHICLE

9. Disconnect the bulb from the socket assembly and
install the replacement bulb.
10. Reinstall the bulb and socket assembly into the
taillamp assembly, and then turn it clockwise.
3 — Tail/Turn Lamp Bulb4 — Tail/Stop Lamp Bulb
378 MAINTAINING YOUR VEHICLE

About Your Brakes.................... 260,262
ABS (Anti-Lock Brake System) ............263,265
Adding Engine Coolant (Antifreeze) .......... 350
Adding Fuel ........................... 302
Adding Washer Fluid ..................... 345
Additives, Fuel ......................... 300
Adjustable Pedals ....................... 134
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 338
Air Conditioner Maintenance ............... 341
Air Conditioning Filter .................237,342
Air Conditioning, Operating Tips ............ 238
Air Conditioning Refrigerant .............341,342
Air Conditioning System ................231,341
Air Pressure, Tires ....................... 282
Airbag .............................. 47,56
Airbag Deployment ....................... 57
Airbag Light ................... 49,55,60,74,165
Airbag Maintenance ....................... 59
Airbag, Side .......................... 53,56Airbag, Window (Side Curtain)
...........50,53,56
Alarm, Panic ............................ 21
Alarm (Security Alarm) .................17,170
Alarm System (Security Alarm) ............... 17
Alterations/Modifications, Vehicle ............. 7
Antenna, Satellite Radio ................... 221
Antifreeze (Engine Coolant) ...........349,350,380
Disposal ............................ 352
Anti-Lock Brake System (ABS) ............263,265
Anti-Lock Warning Light ...............172,265
Anti-Theft Security Alarm (Theft Alarm) ........ 17
Anti-Theft System ....................... 170
Appearance Care ........................ 358
Arming Theft System (Security Alarm) ......... 17
Assistance Towing ....................... 100
Auto Down Power Windows ................ 32
Auto Unlock, Doors ....................... 28
Auto Up Power Windows .................. 33
Automatic Dimming Mirror ................. 82
412 INDEX

Automatic Door Locks................... 27,28
Automatic Headlights .................... 127
Automatic Temperature Control (ATC) ......... 231
Automatic Transaxle Special Additives ...................... 358
Automatic Transmission .............250,356,357
Adding Fluid ...................... 357,382
Autostick ............................ 253
Fluid and Filter Changes ................. 357
Fluid Change ......................... 357
Fluid Level Check ..................... 356
Fluid Type ........................... 382
Shifting ............................. 250
Special Additives ...................... 358
Automatic Transmission Limp Home Mode ..... 252
Autostick ............................. 253
Axle Fluid ............................. 382
Axle Lubrication (Axle Fluid) ............... 382Battery
............................... 339
Keyless Transmitter Replacement (RKE) ....... 21
Location ............................ 339
Belts, Seat ............................ 38,74
Body Mechanism Lubrication ............... 343
B-Pillar Location ........................ 277
Brake Assist System ...................... 266
Brake Control System, Electronic ............. 265
Brake Fluid ............................ 382
Brake, Parking .......................... 260
Brake System ........................ 262,354
Anti-Lock (ABS) .................... 263,265
Fluid Check ....................... 354,382
Master Cylinder ....................... 354
Parking ............................. 260
Warning Light ..................... 169,262
Brakes ............................. 262,354
Brake/Transmission Interlock ............... 248
Break-In Recommendations, New Vehicle ........ 71
10
INDEX 413