maintenance reset DODGE DAKOTA 2005 3.G Owners Manual

Loose Fuel Filler Cap Message
After fuel is added, the vehicle diagnostic system can
determine if the fuel filler cap is loose, improperly
installed, or damaged. A loose fuel filler cap message will
be displayed in the instrument cluster. Tighten the gas
cap until aclickingsound is heard. This is an indication
that the gas cap is properly tightened. Press the odometer
reset button to turn the message off. If the problem
persists, the message will appear the next time the
vehicle is started. This might indicate a damaged cap. If
the problem is detected twice in a row, the system will
turn on the Malfunction Indicator Light (MIL). Resolving
the problem will turn the MIL light off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Lamp)
is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system maynotbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery
replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.
MAINTAINING YOUR VEHICLE 295
7

EMISSION CONTROL SYSTEM MAINTENANCE
The “Scheduled” maintenance services, listed inbold
typeon the following pages must be done at the times or
mileages specified to assure the continued proper func-
tioning of the emission control system. These, and all
other maintenance services included in this manual,
should be done to provide best vehicle performance and
reliability. More frequent maintenance may be needed for
vehicles in severe operating conditions such as dusty
areas and very short trip driving.
Inspection and service also should be done any time a
malfunction is suspected.
NOTE:Maintenance, replacement, or repair of the emis-
sion control devices and systems on your vehicle may be
performed by any automotive repair establishment or
individual using any automotive part which has been
certified pursuant to U.S. EPA or, in the State of Califor-
nia, California Air Resources Board regulations.
EMISSIONS TESTING
In some localities, it may be or will become a legal
requirement to ensure that all emissions components and
systems are functioning properly as a part of the test
procedure. The test center accomplishes this by checking
the On Board Diagnostic System (OBD) system with an
electronic scan tool. If your vehicle has recently been
serviced, the OBD system may have been reset to anot
readycondition because the OBD system has not had
sufficient time since the servicing to reconfirm that
emissions components are operating properly. In most
cases, a reasonable mix and amount of normal city and
highway driving and at least one overnight-off period
will be required to prepare your vehicle for this check;
however your dealer has the equipment and procedures
required to make certain that the OBD system of your
vehicle is ready for the required testing.
348 MAINTENANCE SCHEDULES
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S

Maintenance.......................... 320
Manual........................196,204,320
Shifting............................. 205
Transmitter Battery Service.................. 26
Transmitter, Garage Door Opener............ 133
Transmitter Programming................... 25
Tread Wear Indicators.................... 239
Trip Computer.......................... 127
Trip Odometer.......................... 155
Trip Odometer Reset Button................ 159
Turn Signals...................... 118,152,336
Universal Transmitter..................... 133
Unlock, Auto........................... 18
Vacuum/Vapor Harnesses................. 316
Variance, Compass....................... 132
Vehicle Identification Number................ 5
Vehicle Loading......................230,252Vehicle Modifications/Alterations.............. 6
Vehicle Storage......................... 329
Warning Lights (Instrument Cluster Description) . 152
Warnings and Cautions..................... 5
Warranty Information..................... 370
Washers, Windshield..................... 121
Washing Vehicle......................... 325
Weight Load Carrying.................... 252
Wheel Alignment and Balance............... 241
Wheel and Wheel Trim.................... 326
Wheel Changing........................ 274
Wheel Mounting........................ 278
Wheel Nut Torque....................... 282
Wind Buffeting.......................... 31
Window Fogging........................ 188
Windows.............................. 29
Power............................... 29
Windshield Defroster...................74,186
INDEX 391
10