lights DODGE DURANGO 2013 3.G Service Manual

2. Shift the transmission into NEUTRAL.
3. While still rolling, rotate the AWD control switch tothe desired position.
4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear.
Alternate Procedure
1. Bring the vehicle to complete stop.
2. With the ignition switch in the ON position and the engine either OFF or running, shift the transmission
into NEUTRAL.
3. Rotate the AWD control switch to the desired position.
4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear. NOTE:
If Steps 1 or 2 of either the Preferred or Alternate
Procedure are not satisfied prior to attempting the shift or
if they no longer are being met while the shift attempt is
in process, the desired position indicator light will flash
continuously while the original position indicator light is
ON, until all requirements have been met.
NOTE: The ignition switch must be in the ON position
for a shift to take place and for the position indicator
lights to be operable. If the ignition switch is not in the
ON position, then the shift will not take place and no
position indicator lights will be on or flashing.
NEUTRAL Shift Procedure
1. Turn the ignition switch to the ON position, engine off.
2. Vehicle stopped, with foot on brake.
3. Place the transmission into NEUTRAL.
474 STARTING AND OPERATING

CAUTION!
If the trailer weighs more than 1,000 lbs (454 kg)
loaded, it should have its own brakes and they
should be of adequate capacity. Failure to do this
could lead to accelerated brake lining wear, higher
brake pedal effort, and longer stopping distances.
WARNING!
•Do not connect trailer brakes to your vehicle’s
hydraulic brake lines. It can overload your brake
system and cause it to fail. You might not have
brakes when you need them and could have a
collision.
(Continued)
WARNING! (Continued)
•Towing any trailer will increase your stopping
distance. When towing you should allow for addi-
tional space between your vehicle and the vehicle
in front of you. Failure to do so could result in a
collision.
Towing Requirements – Trailer Lights And Wiring
Whenever you pull a trailer, regardless of the trailer size,
stoplights and turn signals on the trailer are required for
motoring safety.
The Trailer Tow Package may include a four- and seven-
pin wiring harness. Use a factory approved trailer har-
ness and connector.
NOTE: Do not cut or splice wiring into the vehicles
wiring harness.5
STARTING AND OPERATING 559

11. Release the brake pedal for five seconds and ensurethat there is no vehicle movement.
12. Turn the engine OFF, then turn the ignition switch back to the ON/RUN position without starting the
engine.
13. Firmly apply the parking brake.
14. Shift the transmission into PARK.
CAUTION!
Damage to the transmission may occur if the trans-
mission is shifted into PARK with the transfer case in
NEUTRAL (N) and the engine running. With the
transfer case in NEUTRAL (N) ensure that the engine
is OFF before shifting the transmission into PARK.
15. Attach the vehicle to the tow vehicle using a suitable tow bar. 16. Release the parking brake.
17. Disconnect the negative battery cable, and secure it
away from the negative battery post.
NOTE:
• Steps 1 through 6 are requirements that must be met
before pressing the NEUTRAL (N) button, and must
continue to be met until the shift has been completed.
If any of these requirements are not met before press-
ing the NEUTRAL (N) button or are no longer met
during the shift, then the NEUTRAL (N) indicator light
will flash continuously until all requirements are met
or until the NEUTRAL (N) button is released.
• The ignition switch must be in the ON/RUN position
for a shift to take place and for the position indicator
lights to be operable. If the ignition switch is not in the
ON/RUN position, the shift will not take place and no
position indicator lights will be on or flashing.
5
STARTING AND OPERATING 569

NOTE:
•Steps 1 through 7 are requirements that must be met
prior to pressing the NEUTRAL (N) button, and must
continue to be met until the shift has been completed.
If any of these requirements are not met prior to
pressing the NEUTRAL (N) button or are no longer
met during the shift, the NEUTRAL (N) indicator light
will flash continuously until all requirements are met
or until the NEUTRAL (N) button is released. •
The ignition switch must be in the ON/RUN position
for a shift to take place and for the position indicator
lights to be operable. If the ignition switch is not in the
ON/RUN position, the shift will not take place and no
position indicator lights will be on or flashing.
• A flashing NEUTRAL (N) position indicator light
indicates that shift requirements have not been met.
572 STARTING AND OPERATING

Your leather upholstery can be best preserved by regular
cleaning with a damp soft cloth. Small particles of dirt
can act as an abrasive and damage the leather upholstery
and should be removed promptly with a damp cloth.
Stubborn soils can be removed easily with a soft cloth
and MOPARTotal Clean. Care should be taken to avoid
soaking your leather upholstery with any liquid. Please
do not use polishes, oils, cleaning fluids, solvents, deter-
gents, or ammonia-based cleaners to clean your leather
upholstery. Application of a leather conditioner is not
required to maintain the original condition.
WARNING!
Do not use volatile solvents for cleaning purposes.
Many are potentially flammable, and if used in
closed areas they may cause respiratory harm.
Cleaning Headlights
Your vehicle is equipped with plastic headlights and fog
lights (if equipped) that are lighter and less susceptible to
stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and therefore
different lens cleaning procedures must be followed.
To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution fol-
lowed by rinsing.
Do not use abrasive cleaning components, solvents, steel
wool or other aggressive material to clean the lenses.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with MOPAR Glass Cleaner, or any commercial
household-type glass cleaner. Never use an abrasive type
642 MAINTAINING YOUR VEHICLE

Cavity Car-tridgeFuse Mini
Fuse Description
M10 15 Amp
Blue Video/Universal
Garage Door Opener
M11 10 Amp
Red Heating, Ventilation
& Air Conditioning (Climate Control System)
M12 30 Amp
Green Radio/Amplifier
M13 20 Amp
Yellow Instrument Cluster
M14 20 Amp
Yellow Back Up Camera –
If EquippedCavity Car- tridgeFuse Mini
Fuse Description
M15 20 Amp
Yellow Power Seat
Module(s)/
Adaptive Cruise Control/Audio Telematics/
Daytime Running Lights Relay/Air Suspension
Module/Instrument Cluster
M16 10 Amp
Red Occupant Restraint
Controller
M18 15 Amp
Blue Stop Lamp
7
MAINTAINING YOUR VEHICLE 647

Rear Liftgate Mounted Tail Lamp
1. Raise the liftgate.
2. Use a fiber stick or flat blade screw driver to pry thelower trim from the liftgate.
3. Disconnect the two trim panel lights.
4. Tail lamps are now visible. Rotate socket(s) counter clockwise.
5. Remove/replace bulb(s).
6. Reinstall the socket(s)
7. Reverse process to reinstall the liftgate trim.
Center High-Mounted Stop Lamp (CHMSL)
The center high-mounted stop lamp is an LED assembly.
See your authorized dealer for replacement.
Rear License Lamp
1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens.
2. Pull bulb from socket.
3. Replace bulb.
4. Reinstall lens.7
MAINTAINING YOUR VEHICLE 655

•Check function of all interior and exterior lights
Required Maintenance
Refer to the Maintenance Schedules on the following
pages for required maintenance.
At Every Oil Change Interval As Indicated By Oil Change Indicator System:
•Change oil and filter.
• Rotate the tires. Rotate at the first sign of irregu-
lar wear, even if it occurs before the oil indicator
system turns on.
• Inspect battery and clean and tighten terminals as
required.
• Inspect automatic transmission fluid if equipped
with dipstick.
• Inspect brake pads, shoes, rotors, drums, hoses
and park brake.
At Every Oil Change Interval As Indicated By Oil
Change Indicator System:
•Inspect engine cooling system protection and
hoses.
• Inspect exhaust system.
• Inspect engine air cleaner if using in dusty or
off-road conditions.
8
M
A I
N T
E
N
A
N
C E
S
C
H E
D
U L
E
SMAINTENANCE SCHEDULES 661

Adaptive Cruise Control (ACC) (Cruise Control) . . .222
Adding Engine Coolant (Antifreeze)............627
Adding Fuel ............................ .542
Additives, Fuel .......................... .536
Airbag ..................................68
Airbag Deployment ........................79
Airbag Light .............................76
Airbag Maintenance ........................80
Airbag, Side ..............................71
Airbag, Window (Side Curtain) ................72
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . .614
Air Conditioner Maintenance .................616
Air Conditioning Filter .....................617
Air Conditioning, Rear Zone .................430
Air Conditioning Refrigerant .................616
Air Conditioning System ....................423
Air Pressure, Tires ........................ .510
Alarm, Panic .............................26
Alarm (Security Alarm) ......................21 All Wheel Drive (AWD)
.....................468
Alterations/Modifications, Vehicle ...............9
Antenna, Satellite Radio .....................377
Antifreeze (Engine Coolant) ..................626
Disposal ............................ .628
Anti-Lock Brake System (ABS) ................486
Anti-Lock Warning Light ....................314
Anti-Theft System ........................ .318
Appearance Care ........................ .638
Assistance Towing ........................ .147
Assist, Hill Start ......................... .494
Auto Down Power Windows ..................43
Automatic Dimming Mirror ..................121
Automatic Headlights ..................... .201
Automatic Temperature Control (ATC) ..........423
Automatic Transmission ....................449
Adding Fluid ........................ .638
Fluid and Filter Changes .................638
Fluid Change ........................ .638
678 INDEX

Cooling System.......................... .625
Adding Coolant (Antifreeze) ...............627
Coolant Capacity ...................... .656
Coolant Level ........................ .629
Disposal of Used Coolant .................628
Drain, Flush, and Refill ..................626
Inspection ........................... .625
Points to Remember .....................629
Pressure Cap ......................... .628
Radiator Cap ......................... .628
Selection of Coolant (Antifreeze) ............626
Corrosion Protection ...................... .638
Cruise Control (Speed Control) ................222
Cupholders ............................ .282
Customer Assistance ...................... .669
Data Recorder, Event .......................82
Daytime Running Lights ....................203
Dealer Service ........................... .609Defroster, Rear Window
.....................295
Defroster, Windshield ......................110
Dipsticks Automatic Transmission ..................636
Oil (Engine) ...........................611
Power Steering ....................... .482
Disabled Vehicle Towing ....................598
Disposal Antifreeze (Engine Coolant) ...............628
Door Locks ..............................33
Door Opener, Garage ...................... .262
Driving ............................... .475
Driving to Achieve Maximum Fuel Economy ......336
E-85 Fuel .............................. .538
Electrical Outlet, Auxiliary (Power Outlet) ........275
Electric Rear Window Defrost .................295
Electric Remote Mirrors .....................122
Electronically Shifted Transfer Case .............469
10
INDEX 681