DODGE DURANGO 2020 Vehicle Warranty

For Example Only:
Gauge reading of hot tire:.............................................. 32 psi (220 kPa)
If recommended cold inflation pressure is: .................... 30 psi (205 kPa)
Desired gauge reading of hot tire 30 + 4 psi =.............34 psi (205 + 30 = 235 kPa)
Therefore: add 2 psi....................................................... (15 kPa)
Check cold pressure as soon as possible, preferably within 24 hours.
“Bleeding” air from hot tires could result in underinflation. Use an
accurate tire gauge to check pressures. Never allow children to inflate
or deflate tires.
FOR MICHELIN® PAX® SYSTEM TIRES/SELF-SUPPORTING ZERO
PRESSURE (ZP) TIRES CHECK INFLATION PRESSURES AS SOON
AS POSSIBLE FOLLOWING A LOW PRESSURE WARNING
The PAX® System requires a functioning, correctly calibrated on-board
vehicle tire pressure monitoring system (TPMS) to monitor the air
pressure and alert the driver when a low pressure event occurs. Be
certain to ensure that your vehicle’s Tire Pressure Monitoring System
(TPMS) is functioning and is correctly calibrated. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Low pressure warning systems are designed to alert the driver to a low
air pressure situation in at least one tire on the vehicle. While your ZP
tires are designed to provide continued mobility in the event of an air
loss, the sooner you respond to a warning and take corrective action, the
greater the likelihood that the tire can be returned to service.
Always visually inspect your MICHELIN® PAX® System tire and
self-supporting tires and use a pressure gauge to check the air pressure
in all 4 tires following any low pressure warning. (Unless advised to do
otherwise by the manufacturer of your low pressure warning system.)
If the tire pressure is at or below 18 PSI, proceed to the nearest
Authorized PAX System Retailer for PAX tires or a participating Michelin
tire retailer for ZP tires (or a representative of your vehicle manufacturer
if advised to do so in your vehicle owner ’s manual) and have the tire
demounted and thoroughly inspected for possible internal damage.
If you are unable to see any damage to the tire, and the tire pressure is
more than 18 PSI, reinflate your tire to the proper air pressure. (See
instructions for checking pressures when tires are hot.) When tires
have cooled, check air pressure again. If any tire has lost more than
MICHELIN170

5 PSI from the previous pressure check, have the tire inspected at once
by an authorized PAX System Retailer for PAX tires or a participating
Michelin tire retailer (or representative of your vehicle manufacturer if
your vehicle owner ’s manual so advises.) Failure to do so may cause
irreparable damage to the tire and result in sudden tire destruction and
personal injury.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring System
(TPMS) that is designed to monitor the pressure of tires mounted on your
vehicle and sends a signal to the driver if a tire pressure falls below a
predetermined level. A TPMS should not replace monthly manual
pressure checks for all four (4) tires and the spare. We recommend that
you manually monitor and check tire pressure inflation with a pressure
gauge. Your tires should have the recommended pressure listed by your
vehicle’s manufacturer. This information can be found in the vehicle
owner ’s manual and often on a placard located in the vehicle’s door
jamb, inside the fuel hatch, or on the glove compartment door. If you
have a plus size fitment that requires a higher inflation pressure, your tire
pressure monitoring system will require re-calibration to new inflation
pressure. Refer to your tire dealer/installer of plus size tires for proper
inflation pressure.
We recommend checking air pressure once each month, and before a long
trip. Whether you have a full-sized or mini-spare, make sure that it is
properly inflated as well. If the TPMS generates improper monitoring or
signals we recommend that you consult your owner ’s manual provided
with your vehicle and follow-up with your vehicle’s manufacturer.
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
MICHELIN
171

HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop. If you see any damage to a tire or
wheel, replace it with the spare at once and visit a participating
Michelin Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of MICHELIN® tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
SPEED RATINGS
Speed Symbols are shown on the sidewall of some MICHELIN® tires.
The following table shows the maximum speed corresponding to the
symbol.
*Some V (or VR) rated tires may have a speed capacity greater than
149 mph (240 km/h). Consult your participating Michelin® tire retailer
for maximum speed rating if your vehicle capability exceeds this speed.
**Z (or ZR) rated tires are designed to use on cars with maximum speed
capabilities in excess of 149 mph (240 km/h).
(W and Y speed ratings are subcategories of Z).
Consult your Michelin tire retailer for maximum speed capabilities. For
PAX® System Tires consult an authorized PAX System Tire Retailer.
Although a tire may be speed-rated, we do not endorse the operation of
any vehicle in an unsafe or unlawful manner. Speed ratings are based on
laboratory tests which relate to performance on the road, but are not
applicable if tires are underinflated, overloaded, worn out, damaged,
altered, improperly repaired or retreaded.
MICHELIN
172

MICHELIN
Furthermore,
a
tire’s
speed
rating
does
not
imply
that
vehicles
can
be

safely
driven
at
the
maximum
speed
for
which
the
tire
is
rated,

particularly
under
adverse
road
and
weather
conditions
or
if
the
vehicle

has
unusual
characteristics.
Michelin®
highway
passenger
tires
that
do
not
have
a
speed
symbol
on

the
sidewall
have
a
maximum
speed
rating
of
105
mph
(170
kph).
Light

truck
highway
tires


that
do
not
have
a
speed
symbol
on
the
sidewall
of

the
tire
have
a
maximum
speed
rating
of
87
mph
(140
kph).
MICHELIN®

tires
that
do
not
have
a
speed
symbol
on
the

sidewall
or
tires
with
Q
symbols
have
a
speed
rating
of
100
mph

(160
km/h).

tires
with
a
speed
symbol
have
a
maximum
speed

rating
in
accordance
with
the
symbol.
The
speed
and
other
ratings
of
retreaded
tires


are
assigned
by
the

retreader
and
replace
the
original
manufacturer ’s
ratings.
IMPORTANT:
In
order
to
maintain
the
speed
capability
of
the
vehicle,

replacement
tires
must


have
speed
ratings
equal
to
or
higher
than
those

fitted
as
original
equipment
(as
indicated
on
the
vehicle
tire
placard
or

owner ’s
manual).
If
tires
with
lower
speed
ratings
are
fitted,
the
vehicle’s

handling
may
be
affected
and
the
speed
capability
of
the
vehicle
will
be

lowered
to
the
maximum


speed
capability
of
the
replacement
tires
as

indicated
in
the
following
table.
REMEMBER...High
speed
driving
can
be
dangerous
and
may
damage

your
tires.
AND...When
driving
at
highway
speeds,
correct
inflation
pressure
is

especially
important.
173

INSPECT YOUR TIRES, DO NOT DRIVE ON A DAMAGED TIRE
OR WHEEL
HAZARDS
Objects in the road, such as potholes, glass, metal, rocks, wood, debris
and the like, can damage a tire and should be safely avoided. Unavoid-
able contact with such objects should prompt a thorough tire inspection.
Anytime you see any damage to your tires or wheels, replace with the
spare at once and immediately visit any Michelin tire retailer. For PAX®
System Tires see an authorized PAX System tire retailer.
MICHELIN174

IMPACT DAMAGE
A tire impacted by a road hazard (curb, pothole, debris) may be damaged
but not have visible signs of damage on its surface. A tire damaged by an
impact may sustain a sudden failure a day, week, or even months later.
You may not recall hitting an object that damaged or injured your tires.
Air loss, unusual tire wear, localized wear or vibrations can also be signs
of internal tire damage.
If you suspect any damage to your tire or wheel from an impact with a
curb, pothole, debris on the road or any other road hazard, or if you feel
or hear any unusual vibration, replace with a properly inflated spare at
once and immediately visit any qualified tire technician.
INSPECTION
When inspecting your tires, including the spare, check the air pressures.
If the pressure check indicates that one of your tires has lost pressure of
two pounds or more, look for signs of penetration, valve leakage or wheel
damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal tire
wear, particularly on the edges of the tire tread, which may be caused
by misalignment or underinflation. If any such damage is found, the
tire must be inspected by any Michelin tire retailer at once. Use of a
damaged tire could result in tire destruction.
All tires will wear out faster when subjected to high speeds as well as
hard cornering, rapid starts, sudden stops, frequent driving on roads
which are in poor condition, and off road use. Roads with holes and rocks
or other objects can damage tires and cause misalignment of your vehicle.
When driving on such roads, drive carefully and slowly, and before
driving again at normal or highway speeds, examine your tires for any
damage, such as cuts, bulges, penetrations, unusual wear patterns, etc.
WEAR BARS
MICHELIN® tires contain “Wear-Bars” in the grooves of the tire tread
which show up when only 2/32 nds of an inch (1.6 mm) of tread is
remaining. At this stage, your tires must be replaced. Tires worn beyond
this stage are extremely dangerous.
MICHELIN
175

DO NOT OVERLOAD - DRIVING ON ANY OVERLOADED TIRE IS
DANGEROUS
The maximum load rating of your tires is molded on the tire sidewall. Do
not exceed this rating. Follow the loading instructions of the manufac-
turer of your vehicle and this will ensure that your tires are not
overloaded. Tires which are loaded beyond their maximum allowable
loads for the particular application will build up excessive heat that may
result in sudden tire destruction.
Do not exceed the gross axle weight rating for any axle on your vehicle.
TRAILER TOWING
If you anticipate towing a trailer, you should visit any Michelin tire
retailer for advice concerning the correct size tire and pressures. Tire size
and pressures will depend upon the type and size of trailer and hitch
utilized, but in no case must the maximum cold inflation pressure or tire
load rating be exceeded. Check the tire decal and the owner ’s manual
supplied by the manufacturer of your vehicle for further recommenda-
tions on trailer towing.
MICHELIN® PAX® System Tires/Self-Supporting Zero Pressure (ZP)
Tires and Trailer Towing
Operation of Pax or ZP tires at low or zero air pressure with a trailer in
tow, is dangerous and is not recommended. If the low pressure warning
indicator is activated when a trailer is in tow, stop, disconnect the trailer,
and do not continue to tow the trailer until the tire has been repaired and
re-inflated to the proper air pressure. If the tire cannot be repaired, it must
be replaced with a new full size, PAX/ZP tire, and inflated to the proper
air pressure, before the trailer can be safely towed again.
WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR
SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES.
CHECK HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH
MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect excessive
vibration, your vehicle may be out of alignment or balance. These
conditions not only shorten the life of your tires but adversely affect the
handling characteristics of your vehicle, which could be dangerous. If
you detect irregular wear or vibration, have your alignment and balance
MICHELIN176

checked
immediately.
Ti re s
which
have
been
run
underinflated
will
show

more
wear
on
the
shoulders
than
in
the
center
of
the
tread.
TIRE MIXING
MICHELIN®
tires
are
radial
tires
and
for
best
performance
it
is
recom-
mended
that
the
same
size
and
type
of
tire
be
used
on
all
four
wheel

positions.
Before
mixing
tires
of
different
types
in
any
configuration
on

any
vehicle,
be
sure
to
check
the
vehicle
manufacturer ’s
owner‘s
manual

for
its
recommendations.
It
is
especially
important
to
check
the
vehicle
manufacturer ’s
owner

’s

manual
when
mixing,
matching,
or
replacing
tires
on
4-wheel
drive

vehicles,
as
this
may
require
special
precautions.
MICHELIN
DOES
NOT
RECOMMEND
MIXING
PAX®
SYSTEM
TIRES

WITH
NON-PAX
TIRES
/
SELF-SUPPORTING
ZERO
PRESSURE
(ZP)

TIRES
WITH
NON-ZP
TIRES
OTHER
THAN
THE
TEMPORARY
USE

OF
THE
SPARE
IF
THE
VEHICLE


IS
SO
EQUIPPED.
:,17(5 DRIVING
Ti re s
which
meet
the
Rubber
Manufactures
Association
(RMA)
definition

of
snow
tires
are
marked
M/S,
or
M&S.
On
such
tires,
this
designation
is

molded
into
the
sidewall.
Tires
without
this
notation
are
not
recom-
mended
or

driving.
While
All-Season
tires
are
designed
to
provide
reliable

performance
in
some

conditions,
the
use
of
four

(4)

tires
is
recommended
for
optimal
performance.

Tires
designate
for
use
in
severe

conditions
are

marked
on
at
leas
one
sidewall
with
the
letter
“M”
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires.
Refer to your vehicle owner ’s manual for instructions on tire rotation. If
you do not have an owner‘s manual for your vehicle, Michelin recom-
mends rotating your tires every 6,000 to 8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be
rotated at the first sign of irregular wear, even if it occurs before 6,000
miles (10,000 km). This is true for all vehicles.
MICHELIN
177

When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
that a tire has been moved to a different position on your vehicle. Make
certain that your TPMS system is reset, if necessary, so as to correctly
identify the location of each tire on your vehicle. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle
manufacturer ’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner ’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
Replacement of Two (2) Tires
It is recommended that all four (4) tires are replaced at the same time.
However, when only two tires are replaced, the new tires should be put
on the rear. The new tires, with deeper tread, may provide better grip and
water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
MICHELIN178

avoid sudden, sharp turns or lane changes and obey all traffic laws.
Failure to do so may result in loss of vehicle control leading to an accident
and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires.
Alterations may prevent proper performance, leading to tire damage
which can result in an accident. Tires which become unserviceable due to
alterations such as truing, whitewall inlays, addition of balancing or
sealant liquids, or the use of tire dressing containing petroleum distillates
are excluded from warranty coverage.
REPAIRS WHEREVER POSSIBLE, SEE YOUR MICHELIN® TIRE
RETAILER AT ONCE
If any MICHELIN® tire sustains a puncture, have the tire demounted and
thoroughly inspected by any Michelin tire retailer for possible damage that
may have occurred. A tread area puncture in any MICHELIN® passenger or
light truck tire can be repaired provided that the puncture hole is not more
than 1/4” in diameter, not more than one radial cable per casing ply is
damaged, and the tire has not been damaged further by the puncturing
object or by running underinflated. Tire punctures consistent with these
guidelines can be repaired by following the Rubber Manufacturers Asso-
ciation (RMA) recommended repair procedures.
TIRE REPAIRS
Repairs of all tires must be of the combined plug and inside patch type.
Your MICHELIN® PAX® System tires must be removed from the wheel
for inspection prior to repair. Plug only repairs are improper. A tire
should be removed from the rim and inspected prior to repair. Any tire
repair done without removing the tire from the rim is improper. An
improperly repaired tire will cause further damage to the tire by either
leaking air or allowing air, moisture and contaminants to enter the
structure of the tire. An improperly repaired tire can fail suddenly at a
later date.
Never repair a tire with less than 2/32 nds of an inch tread remaining. At
this tread depth, the tire is worn out and must be replaced.
MICHELIN
179