spare tire DODGE DURANGO 2021 Vehicle Warranty

MICHELIN®
165
all provisions of the limited warranty are void. For a list of approved
systems, see an authorized PAX® System retailer, or call toll free:
1-877-PAX TIRE or 1-877-729-8473
For all types of tires, consult your vehicle tire placard or owner’s
ma
nual for recommended operating pressures. If the tires are
purchased as replacement tires, operating instructions for the low
pressure warning system will be provided by the manufacturer of that
system. Recommended operating pressures will be provided by a
participating Michelin® tire retailer for self supporting ZP tires.
Recommended operating pressure for PAX® System Tires will be
provided by a PAX System retailer. These inflation pressures must be
maintained as a minimum. However, do not exceed the maximum
pressure rating indicated on the tire sidewall.
CHECK THE COLD INFLATION PRESSURES IN ALL YOUR
T I

RES, INCLUDING THE SPARE, AT LEAST ONCE EACH
MONTH
Failure to maintain correct inflation may result in improper vehicle
ha
ndling and may cause rapid and irregular tire wear, sudden tire
destruction, loss of vehicle control and serious personal injury.
Therefore, inflation pressures should be checked at least once each
month and always prior to long distance trips. This applies to all tires,
including sealant types, and Self-Supporting Zero Pressure (ZP) tires
which are as susceptible to losing air pressure as any other type of tire
if not properly maintained.
UNDERINFLATION
It is impossible to determine whether tires are properly inflated by
si
mply looking at them. It is almost impossible to “feel or hear” when
a tire is being run underinflated or nearly flat. Tires must be checked
monthly with a tire pressure gauge.
Pressures should be checked when tires are cold, in other words,
be
fore they have been driven on. Driving, even for a short distance,
causes tires to heat up and air pressure to increase.
Checking pressure when tires are hot:
If pressures are checked after tires have been driven for more than
th
ree minutes or more than one mile, (2 km) the tires become hot and
th

e pressures will increase by approximately 4 psi. Therefore when the
tire pressure is adjusted under these conditions, it should be increased
to a gauge reading of 4 psi greater than the recommended cold
inflation pressure.

MICHELIN®
167
instructions for checking pressures when tires are hot. When tires
have cooled, check air pressure again. If any tire has lost more than
5 PSI from the previous pressure check, have the tire inspected at
once by an authorized PAX® System Retailer for PAX® tires or a
participating Michelin® tire retailer or representative of your
vehicle manufacturer if your vehicle Owner’s Manual so advises.
Failure to do so may cause irreparable damage to the tire and result
in sudden tire destruction and personal injury.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring
Sy
stem (TPMS) that is designed to monitor the pressure of tires
mounted on your vehicle and sends a signal to the driver if a tire
pressure falls below a predetermined level. A TPMS should not
replace monthly manual pressure checks for all four tires and the
spare. We recommend that you manually monitor and check tire
pressure inflation with a pressure gauge. Your tires should have the
recommended pressure listed by your vehicle’s manufacturer. This
information can be found in the vehicle Owner’s Manual and often on
a placard located in the vehicle’s door jamb, inside the fuel hatch, or
on the glove compartment door. If you have a plus size fitment that
requires a higher inflation pressure, your tire pressure monitoring
system will require re-calibration to new inflation pressure. Refer to
your tire dealer/installer of plus size tires for proper inflation
pressure.
We recommend checking air pressure once each month, and before a
l o

ng trip. Whether you have a full-sized or mini-spare, make sure that
it is properly inflated as well. If the TPMS generates improper
monitoring or signals we recommend that you consult your Owner’s
Manual provided with your vehicle and follow-up with your vehicle’s
manufacturer.
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
sp

eedometer. Excessive speed in a free-running, unloaded tire can
cause it to “explode” from centrifugal force. The energy released by
such an explosion is sufficient to cause serious physical injury or
death. Never allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not
en
gage in excessive wheel spin. Accelerating the motor excessively,
particularly with automatic transmission vehicles, may cause a drive

MICHELIN®
168
tire that has lost traction to spin beyond its speed capability. This is
also true when balancing a drive tire/wheel assembly on the vehicle
using the vehicle engine to spin the tire/wheel assembly.
HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important. H
owever, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover,
driving at high speed reduces the reaction time available to avoid
accidents and bring your vehicle to a safe stop. If you see any damage
to a tire or wheel, replace it with the spare at once and visit a
participating Michelin® tire retailer.
Exceeding the maximum speeds shown on the following page for each
ty
pe of Michelin® tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire
destruction and rapid air loss. Failure to control a vehicle when one or
more tires experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated
by
the legal limits and driving conditions.
SPEED RATINGS
Speed Symbols are shown on the sidewall of some Michelin® tires.
Th
e following table shows the maximum speed corresponding to the
symbol.
*Some V (or VR) rated tires may have a speed capacity greater than
14
9 mph (240 km/h). Consult your participating Michelin® tire
re

tailer for maximum speed rating if your vehicle capability exceeds
this speed.
**Z (or ZR) rated tires are designed to use on cars with maximum
sp
eed capabilities in excess of 149 mph (240 km/h).
(W and Y speed ratings are subcategories of Z).
Consult your Michelin® tire retailer for maximum speed capabilities.
Fo
r PAX® System Tires consult an authorized PAX® System Tire
Retailer. Although a tire may be speed-rated, we do not endorse the
operation of any vehicle in an unsafe or unlawful manner. Speed
ratings are based on laboratory tests which relate to performance on
the road, but are not applicable if tires are underinflated, overloaded,
worn out, damaged, altered, improperly repaired or retreaded.

MICHELIN®
171
IMPACT DAMAGE
A tire impacted by a road hazard (curb, pothole, debris) may be
da
maged but not have visible signs of damage on its surface. A tire
damaged by an impact may sustain a sudden failure a day, week, or
even months later. You may not recall hitting an object that damaged
or injured your tires. Air loss, unusual tire wear, localized wear or
vibrations can also be signs of internal tire damage.
If you suspect any damage to your tire or wheel from an impact with
a
curb, pothole or debris on the road or any other road hazard, or if
you feel or hear any unusual vibration, replace with a properly
inflated spare at once and immediately visit any qualified tire
technician.
INSPECTION
When inspecting your tires, including the spare, check the air
pr
essures. If the pressure check indicates that one of your tires has lost
pressure of two pounds or more, look for signs of penetration, valve
leakage or wheel damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal
ti
re wear, particularly on the edges of the tire tread, which may be
caused by misalignment or underinflation. If any such damage is
found, the tire must be inspected by any Michelin® tire retailer at
once. Use of a damaged tire could result in tire destruction.
All tires will wear out faster when subjected to high speeds as well as
ha
rd cornering, rapid starts, sudden stops, frequent driving on roads
which are in poor condition, and off road use. Roads with holes and
rocks or other objects can damage tires and cause misalignment of
your vehicle. When driving on such roads, drive carefully and slowly,
and before driving again at normal or highway speeds, examine your
tires for any damage, such as cuts, bulges, penetrations, unusual wear
patterns, etc.
WEAR-BARS
Michelin® tires contain “Wear-Bars” in the grooves of the tire tread
wh
ich show up when only 2/32nds of an inch (1.6 mm) of tread is
re

maining. At this stage, your tires must be replaced. Tires worn
beyond this stage are extremely dangerous.

MICHELIN®
173
alignment and balance checked immediately. Tires which have been
ran underinflated will show more wear on the shoulders than in the
center of the tread.
TIRE MIXING
Michelin® tires are radial tires and for best performance it is
re
commended that the same size and type of tire be used on all four
wheel positions. Before mixing tires of different types in any
configuration on any vehicle, be sure to check the vehicle
manufacturer’s owner‘s manual for its recommendations.
It is especially important to check the vehicle manufacturer’s Owner’s
Ma
nual when mixing, matching, or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
MICHELIN® DOES NOT RECOMMEND MIXING PAX® SYSTEM
TI
RES WITH NON-PAX TIRES/SELF-SUPPORTING ZERO
PRESSURE (ZP) TIRES WITH NON-ZP TIRES OTHER THAN THE
TEMPORARY USE OF THE SPARE IF THE VEHICLE IS SO
EQUIPPED.
WINTER DRIVING
Tires which meet the US Tire Manufacturers Association (USMTA)
de
finition of snow tires are marked M/S, or M&S. On such tires, this
designation is molded into the sidewall. Tires without this notation
are not recommended or Winter driving.
While All-Season tires are designed to provide reliable
performance in some Winter conditions, the use of four
Wi
nter tires is recommended for optimal performance.
Tires designate for use in severe Winter conditions are
marked on at least one sidewall with the letter “M”
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires.
Re
fer to your vehicle owner’s manual for instructions on tire rotation.
If you do not have an owner‘s manual for your vehicle, Michelin®
recommends rotating your tires every 6,000 to 8,000 miles (10,000 to
12

,000 km).
Monthly inspection for tire wear is recommended. Your tires should
be
rotated at the first sign of irregular wear, even if it occurs before
6,000 miles (10,000 km). This is true for all vehicles.

MICHELIN®
174
When rotating tires with a directional tread pattern, observe the
arrows molded on the sidewall which show the direction the tire
should turn. Care must be taken to maintain the proper turning
direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
th
at a tire has been moved to a different position on your vehicle.
Make certain that your TPMS system is reset, if necessary, so as to
correctly identify the location of each tire on your vehicle. Refer to
your vehicle owner’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as
fr
ont and rear position tire pressure may vary according to the vehicle
manufacturer’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and
co
nstruction should be used in a five tire rotation. Always check the
inflation pressure of the full-size spare immediately before
incorporating it into rotation. Follow the vehicle manufacturer’s
recommended pattern for rotation, or if not available, see a qualified
tire technician.
Replacement of Two Tires
It is recommended that all four tires are replaced at the same time.
Ho
wever, when only two tires are replaced, the new tires should be
put on the rear. The new tires, with deeper tread, may provide better
grip and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SU
VS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SU
Vs and light trucks do not have the same handling characteristics
as automobiles. Because of these differing characteristics, failure to
operate your SUV/truck in a proper and safe manner can increase the
likelihood of vehicle rollover. Modifications to your SUV/truck tire
size, tire type, wheels or suspension can change its handling
characteristics and further increase the likelihood of vehicle rollover.
Whether your SUV/truck has the original equipment configuration
for tires, wheels and suspension or whether any of these items have

MICHELIN®
178
APPLICATIONS, THE TIRES MAY BECOME UNSERVICEABLE AT
LOW OR ZERO PRESSURE, CAUSING SERIOUS PERSONAL
INJURY OR DEATH.

SPECIAL MOUNTING INSTRUCTIONS FOR MICHELIN® TRX™
TI
RES

The MICHELIN® TRX™ tire is a tubeless tire that must only be
mo
unted on special wheels (TR or JM type) with millimetric seat
diameter. If TRX tires are mounted on standard wheels, they will not
retain air due to an air escape feature designed into the bead area of
these tires.
Do not try to override this feature by mounting TRX tires with
tu
bes. The MICHELIN® TRX™ tire must be used on all wheel
positions.
TEMPORARY TYPE SPARE TIRES
When using any temporary type spare tire, be sure to follow the
ve
hicle manufacturer’s instructions.
READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
DOT XXXX XXXX XXX (1990-1999)
DOT XXXX XXXX XXXX (after July 2000)
THE DOT
The “DOT” symbol certifies tire manufacturer’s compliance with US
De
partment of Transportation tire safety standards. Next to the
symbol is the tire identification or “serial number”. The first two
characters identify the plant where the tire was manufactured. The
next two characters reflect the tire size. The following one to four
digits may be used at the tire manufacturer’s option as a descriptive
code. The last three characters are numbers identifying the week and
year of manufacture. (Example: “O25” means second week of the year
of decade, eg.: 1995, 1985, etc.) For the 1990-1999 decade MICHELIN®
brand tires are marked with a triangle pointing to the last three
numeric characters. Tires produced after July 2000 have an additional
digit to identify a given decade. For example, 2800 means the tire was
pr

oduced during the 28th week of 2000; 0201 during the 2nd week of
2001. If the last digits of your DOT number contains three numeric
characters and is not marked with a triangle, consult a qualified tire
technician to determine the year of manufacture.

MICHELIN®
179
SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK TIRES
INCLUDING SPARE TIRES
The following recommendation applies to passenger car and light
tr
uck tires. Tires are composed of various types of material and rubber
compounds, having performance properties essential to the proper
functioning of the tire itself. These component properties evolve over
time. For each tire, this evolution depends upon many factors such as
weather, storage conditions, and conditions of use (load, speed,
inflation pressure, maintenance etc.) to which the tire is subjected
throughout its life. This service-related evolution varies widely so that
accurately predicting the serviceable life of any specific tire in advance
is not possible.
That is why, in addition to regular inspections and inflation pressure
m a

intenance by consumers, it is recommended to have passenger car
and light truck tires, including spare tires, inspected regularly by a
qualified tire specialist, such as a tire dealer, who will assess the tire’s
suitability for continued service. Tires which have been in use for five
years or more should continue to be inspected by a specialist at least
annually. Consumers are strongly encouraged to be aware not only of
their tires’ visual condition and inflation pressure but also of any
change in dynamic performance such as increased air loss, noise or
vibration, which could be an indication that the tires need to be
removed from service to prevent tire failure. It is impossible to predict
when tires should be replaced based on their calendar age alone.
However the older a tire the greater the chance that it will need to be
replaced due to the service-related evolution or other conditions
found upon inspection or detected during use.
While most tires will need replacement before they achieve 10 years,
i t

is recommended that any tires in service 10 years or more from the
date of manufacture, including spare tires, be replaced with new tires
as a simple precaution even if such tires appear serviceable and even
if they have not reached the legal wear limit. For tires that were on an
original equipment vehicle (i.e., acquired by the consumer on a new
vehicle), follow the vehicle manufacturer’s tire replacement
recommendations, when specified (but not to exceed 10 years).
The date when a tire was manufactured is located on the sidewall of
ea
ch tire. Consumers should locate the Department of Transportation
(DOT) code on the tire which begins with DOT and ends with the
week and year of manufacture. For example, a DOT code ending with
“2204” indicates a tire made in the 22nd week (May) of 2004.

NEXEN TIRE
187
to a toll free phone number to call in case of a flat tire. A qualified
professional will change your flat tire with your spare tire free of
charge. If a working spare is not available, towing will be provided
free of charge to the nearest NEXEN TIRE dealer or authorized place
of repair.
*Nexen Tire reserves the right to change the terms and conditions of
al
l warranties at any time.
TIRE CARE AND MAINTENANCE GUIDE
Tire failure can result in serious damage and/or personal injury. To
re
duce the risk of tire failure we recommend the following:
• Maintain proper inflation pressure and do not use at under inflation
o
r over inflation. Pressure should be set at the level recommended
by vehicle manufacturer.
• Wheel alignment and balancing should be checked at regular inter -
v
als.
• Do not overload. The maximum load carrying capacity is molded on
t
he sidewall of the tire.
• Do not spin your tires excessively and avoid driving over curbs,
p
otholes, obstacles and edges of pavement.
• Never drive on smooth (bald) tires. By law, tires must be replaced
w
hen 2/32" of tread depth remained, as indicated by tread wear
indicator molded in the tread grooves.
• Check your tires frequently for any scrapes, cuts, foreign objects,
s
eparations or bulges. If damage is found, do not attempt to
dismount a tire yourself. Change damaged tire with the spare and
contact a local authorized NEXEN TIRE dealer immediately.
• Do not drive in excess of speed limits allowed by law or the
m
aximum speed justified by driving conditions.
• To achieve proper even wear and gain maximum tread life, tire rota -
t
ion at regular intervals is required.

PIRELLI TIRES
208
TO MAINTAIN PROPER VEHICLE DYNAMICS AND LOAD
CARRYING CAPACITY, REPLACEMENT TIRES MUST ALWAYS
HAVE A LOAD INDEX AND SPEED SYMBOL EQUAL TO OR
GREATER THAN THOSE FITTED AS ORIGINAL EQUIPMENT.
When making plus size fitments, you should consult with the dealer
re
garding any suspension or braking system modifications which
may be recommended for the vehicle.
9. Tire Inspection
As a minimum, tires (including the spare tire) should be examined
an
d air pressure checked monthly and always prior to long trips. They
should also be examined if you strike any unusual object on the road.
Tires showing bulges, cracks, cuts, penetrations or uneven wear must
be dismounted and examined by an authorized Pirelli tire dealer and
replaced if necessary. Pirelli tires have treadwear indicators in the
tread grooves, which show up when the tread has worn to 2/32”
remaining. At this point, your tires must be replaced because they are
illegal and dangerous.
The mere passage of time (age) does not cause tires to deteriorate, but
ra
ther exposure to outside forces. Such outside forces can include, but
are not limited to: road hazards, punctures, improper repairs,
misalignment, under inflated operation, over inflated operation,
excessive heat caused by over deflected operation, excessive exposure
to ozone, improper storage conditions, etc. Tire companies can only
have an impact on a few of these exposures. Tire companies add
antiozinants and anti-oxidants (anti-degradation compounds) to
minimize degradation. Pirelli believes that since there is no way to
accurately predict what outside forces a tire will be exposed to there is
no scientifically supportable age limit that can be set for tires.
To avoid cosmetic damage, use a mild soap solution to clean sidewalls
a n

d rinse off with low-pressure tap water. Never apply cleaners or
dressings to enhance sidewall appearance to avoid removal of
antioxidants, which are intended to prevent ozone degradation. The
removal of anti-oxidants may degrade the rubber and can lead to
sidewall cracking. Use of high-pressure sprayers may cause sidewall
damage.
WARNING!
Driving on a damaged tire is dangerous, as the tire can suddenly
fa
il, which can lead to an accident and serious personal injury or
death.