inflation pressure DODGE DURANGO 2022 Vehicle Warranty
[x] Cancel search | Manufacturer: DODGE, Model Year: 2022, Model line: DURANGO, Model: DODGE DURANGO 2022Pages: 200, PDF Size: 6.72 MB
Page 71 of 200
CONTINENTAL TIRE
70
TEMPORARY SPARE TIRE OWNERS
CTA does not recommend any repair to or reuse of punctured Temporary Spare Tires.
CONTISEAL™ TIRE OWNERS
A ContiSeal™ tire differs from a non-ContiSeal™ tire in that it has a
sticky, viscous layer from shoulder to shoulder along the inner liner.
T h
is layer is an integral part of the ContiSeal™ tires. It is not designed or intended to act
as a permanent puncture repair (See information below). If an object up to 3/16 of an
inch (5 mm) diameter penetrates the tread of the ContiSeal™ tire, this sticky, viscous
l a
yer is designed to surround and adhere to the puncturing object and prevent air loss
from the tire by providing a near instantaneous seal. If the puncturing object becomes
dislodged from the tire, the material is designed to seal most holes made by objects up
to 3/16 of an inch (5 mm) diameter. While ContiSeal™ tires significanty reduce the
i n
cidence of flats they are not designed to be driven under inflated or in a flat condition.
In all other aspects, ContiSeal™ tires perform exactly like non-ContiSeal™ tires. As with
any tire, regularly inspect ContiSeal™ tires for evidence of cuts, punctures, and loss of
inflation pressure. At a minimum, ContiSeal™ tires should be inspected once or twice a
month and always before a long trip. Punctures or damage not attended to promptly can
result in loss of inflation pressure and/or damage to the tire. ContiSeal™ tires with cuts
and punctures must be inspected by a trained tire specialist as soon as possible. The
trained specialist, must inspect the tire carefully and, according to industry standards, to
determine whether a permanent repair can be made or whether the tire must be
removed from service and scrapped. A permanent repair will require removal of the tire
from the rim and application of a repair method specifically approved for the ContiSeal™
tires.
ContiSeal™ tires are identified by a symbol on the tire sidewall.
CONTISILENT™ TIRE OWNERS
ContiSilent™ tires are designed to reduce noise generated while
driving. A ContiSilent™ tire is lined with a noise reducing foam
i n
sert. It is not designed or intended to act as a puncture repair.
USING ContiSilent™ Tires
In aspects such as mounting, demounting, inflating and balancing, ContiSilent™ tires do
n o
t differ from non-ContiSilent™ tires. As with any tire, regularly inspect ContiSilent™
tires for evidence of cuts, punctures, and loss of inflation pressure. At a minimum,
ContiSilent™ tires should be inspected once or twice a month and always before a long
trip. Punctures or damage not attended to promptly can result in loss of inflation
pressure and/or damage to the tire. ContiSilent™ tires with cuts and punctures must be
inspected by a trained tire specialist as soon as possible. The trained tire specialist must
inspect the tire carefully and, according to industry standards, determine whether a
permanent repair can be made or whether the tire must be removed from service and
scrapped.
Page 73 of 200
72
FALKEN TIRE CORPORATION
FALKEN
MADE BY SUMITOMO RUBBER INDUSTRIES
Congratulations!
Your new vehicle is fitted with high performance and high quality Falken tires.
In order to guarantee that you receive the best performance and quality from your new
Fal
ken tires, we recommend that you read and follow all of the maintenance and safety
tips provided in this document. We also suggest that you have your Falken tires
periodically inspected and maintained by a qualified tire service professional.
A) TIRE CARE AND RECOMMENDATIONS
PROPER INFLATION AND FUEL ECONOMY
Ensure maximum performance and a long life from your tires by checking the air pressures
at
least once a month and set them to the vehicle manufacturer’s recommended
pressure(s) listed on the vehicle’s tire placard or in your Owner’s Manual. Always check and
adjust your air pressure when your tires are cold, preferably first thing in the morning before
driving. Never release air pressure from tires when they are hot. Wait until the tires cool
down and recheck, adding air or releasing as required. Falken endorses the use of nitrogen
in your tires because it helps your tires maintain optimal pressure for longer periods of time
and reduces the amount of moisture inside of the tire and wheel assembly.
Some plus size applications may require different air pressure(s) than what is listed on
yo u
r vehicle’s placard or Owner’s Manual. In this case, please consult your tire dealer or
Falken Tire for proper inflation pressure(s).
TIRE INFLATION PRESSURE
Tires need to be properly inflated to effectively operate and perform as intended. Tires
ca r
ry the weight of the vehicle, passengers, and cargo as well as bear the forces of
braking, accelerating, and turning. The vehicle manufacturer sets the inflation pressures
for the original equipment tires that are on your vehicle.
Driving with improperly inflated tires is dangerous. An underinflated tire will generate
ex c
essive heat build-up that will cause damage to the internal structure and inner liner
of the tire. Besides tire damage, improper tire inflation pressures can also affect your
vehicle’s ride and handling, tire tread wear, and fuel economy. It is recommended to
always keep all of your tires, including the spare, at the vehicle manufacturer’s
recommended inflation pressures and be sure to check the air pressure monthly and
before going on long road trips or carrying extra weight in your vehicle.
Your vehicle’s tire placard and/or Owner’s Manual will list the cold inflation pressure(s)
fo r
your vehicle’s original equipment tires, including the spare. The placard can be found
on the driver side door or door jamb area. If you have questions about understanding
your vehicle’s tire placard, please refer to your Owner’s Manual or ask a qualified tire
service professional.
Page 79 of 200
FALKEN TIRE CORPORATION 78
Possible non-Covered Reasons/Conditions:
3. OWNER’S OBLIGATIONS
At least monthly, the vehicle owner(s) should check the tires’ air pressure with a
gauge and inflate to the recommended cold air pressure level listed on the driver
door placard. Do not rely on car servicers to perform the checks. The tires should
be rotated at least every 8,000 km (5,000 miles) or earlier if uneven wear is oc -
curring, and proof of maintenance records should be kept. The owner(s) should
h a
ve the tires rebalanced if vibration is experienced, and the vehicle’s alignment
should be checked if uneven or rapid wear is occurring, or when suggested by
the vehicle’s manufacturer.
All warranty claims must be presented to an authorized Falken dealer or partici -
pating car dealership. The owner(s) must present any supporting maintenance
r e
cords and documentation necessary to help determine if the tire(s) in question
are deemed covered by the limited warranty or not.
4. LEGAL RIGHTS
All implied warranties, including warranties of merchantability and fitness for a
particular purpose shall be limited in duration to the above period. To the extent
permitted by law, Falken Tire Corporation shall not be responsible for incidental
or consequential damages, such as loss of use of the tire or the vehicle on which
it is used, inconvenience, or commercial loss, some states do not allow limita -
tions on how long an implied warranty lasts, or the exclusion or limitation of inci -
dental or consequential damages, so the above limitations or exclusions may not
a p
ply to you. This warranty gives you specific legal rights and you may also have
other rights, which vary from state to state. This is the only express warranty ap -
plicable to Falken brand tires and supersedes the terms of any previous warran -
ty. Falken neither assumes nor authorizes anyone to make or assume for it any
o t
her warranty.
Chipping/Chunking/Tearing Puncture
Corrosion/Wreck Racing or any Competition
Fire Repair Failure
Impact Break or Concussions Road Hazards
Improper Inflation Pressure Sidewall Cut or Damage
Improper Mounting/Dismount Theft or Vandalism
Mechanical Defects of the Vehicle Tread Cuts
Misalignment Wheel Imbalance
Misapplication Willful Abuse
Overloading
Page 81 of 200
FALKEN TIRE CORPORATION 80
DOT Symbol And DOT Serial Code
The “DOT” symbol claims that the tire conforms to all applicable US DOT motor vehicle
sa
fety standards for tires. The identification/serial number follows the “DOT” symbol.
Here is an example of a DOT serial code:
TIRE SIDEWALL LABELING
MAX LOAD AND INFLATION
The maximum load and inflation pressure are marked on the tire sidewall in english and
m e
tric units.
PLY COMPOSITION AND MATERIALS
The number of plies and their generic composition of cord materials in the sidewall and
tr
ead areas can be found on at least one sidewall of a tire.
(a) DOT Symbol (d) Tire Manufacturer’s Code
(b) Manufacture Plant Code (e) Week of Production (01-52)
(c) Tire Size Code (f) Year of Production (last two digits of year)
Page 91 of 200
GENERAL TIRE
90
(“Authorized Dealer”). CTNA will replace the tire pursuant to the terms of this Limited
Warranty and Adjustment Policy. Tires that are replaced under an adjustment basis
under this Limited Warranty and Adjustment Policy become the property of CTNA.
OWNER’S OBLIGATIONS
To make an eligible claim under this Limited Warranty and Adjustment Policy, the owner
must present a claim with the tire to an authorized dealer. For the nearest authorized
dealer, consult the Yellow Pages, the General brand internet address, or the 800 telephone
numbers shown on the back of this Limited Warranty and Adjustment Policy. Owner must
present new vehicle registration form or new vehicle sales invoice indicating the date of
purchase. Owner will be required to sign the CTNA Limited Warranty Claim Form or dealer
replacement sales receipt.
Owner is responsible for paying all applicable taxes set forth under this Limited Warranty
and
Adjustment Policy. Owner is also responsible for paying local tire disposal fees and any
parts or service regardless of mileage or months of service. This includes payment for tire
rotation, alignment, towing, road service, valve stems and tire repairs. Owner is
responsible for maintaining proper tire air pressure and for proper maintenance of the tire.
SAFETY WARNING:
Ignoring any of the safety and information contained in this limited warranty and
Adjustment Policy may result in tire failure, causing serious injury or death.
• Tire failure due to underinflation/overloading.
Follow vehicle Owner’s Manual or tire
placard in vehicle for proper inflation and loading.
• Explosion of tire/rim assembly due to improper tire mounting.
Tire mounting /
demounting can be dangerous. It should be performed only by a trained tire specialist
using proper tools and procedures. Prior to tire mounting/demounting, the Rubber
Manufacturers Association (RMA) wall charts and manuals should be read to obtain
the proper procedures. The failure to follow these procedures may result in faulty posi -
tioning of the tire and/or rim, which may cause the assembly to burst with force suffi -
cient to cause injury or death.
• T
ire failure due to damage.
Inspect your tires frequently for scrapes, bulges, separations,
cuts, snags and other damage from road hazards. Damage from impact can occur to the
inner portions of your tire without being visible to the outside. If you suspect a tire has
been damaged from striking anything unusual in the road, you must have the tire
removed from the rim and inspected both inside and out by a trained tire specialist. Air
loss or unusual tire wear can also be warning signs that a tire may have internal damage.
If you notice these conditions, have your tire inspected by a trained individual.
• Tire failure due to excessive tire spinning.
Avoid tire spinning. The centrifugal force
generated by a free-spinning tire/rim assembly may cause a sudden tire explosion
resulting in vehicle damage and/or serious injury or death. Never exceed 35 mph
( 5
5 km/h) as indicated on your speedometer when your vehicle is stuck in snow, mud,
o r
sand and your tire(s) is/are spinning. Use a gentle backward and forward rocking
motion to free your vehicle for continued driving. Never stand or permit anyone else to
stand near or behind a tire spinning while attempting to push a vehicle that is stuck.
Page 97 of 200
GOODYEAR® DUNLOP® TIRES
96
•TIRE SPINNING. On slippery surfaces such as snow, mud, ice, etc., do not spin tires in
excess of 35 mph (55 km/h), as indicated on the speedometer.
• EXCESSIVE WHEEL SPINNING.
This can also result in tire disintegration or axle failure.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and performance from your
Goodyear® or Dunlop® tires is to give them a simple but frequent (at least monthly)
inspection for proper inflation, even tread wear and the presence of any damage.
DO MAINTAIN PROPER INFLATION PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire performance, safety and fuel
economy. Check inflation pressures at least once a month and before long trips. Use an
accurate tire pressure gauge. Always check pressures when the tires are cold (when the
vehicle has been driven less than one mile). If you must check inflation when the tires
are hot, add 4 psi (27 kPa) to the recommended cold inflation pressure. It is difficult to
tell just by looking at radial tires whether they are underinflated.*
Furthermore, when operating a vehicle equipped with radial tires, it is difficult to notice
wh
en a tire has gone flat or nearly flat since the “feel” of the vehicle does not change
significantly.
*Evidence of air loss or repeated underinflation always requires expert inspection to
d e
termine the source of leakage and tire removal to determine repairability. To avoid
injury, NEVER attempt to reinflate a tire that has been run severely underinflated.
Progressive air loss may result from punctures, cuts, curbing, impacts or partial bead
unseating. Some fitment causes for air loss are (1) incomplete bead seating, (2) bead
tearing caused by a machine tool due to insufficient lubrication or improper adjustment.
Leaking valve core or rubber valve components should be replaced when problems are
detected and whenever tires are replaced.
WARNING!
Vehicle handling, traction, ride comfort and other performance parameters may be
significantly affected by a change in tire size or type. Before replacing tires, always
consult and follow the vehicle Owner’s Manual because some vehicle manufacturers
prohibit changing tire size. When selecting tires that are different from the original
equipment size make certain:
• The tires have adequate load-carrying capacity based on the vehicle placard.
•
The tires have sufficient inflation pressure to carry the load.
•
There is proper clearance with no interference points between the tire and vehicle.
T
he consumer must be aware to always drive safely and obey all traffic laws. Avoid
s u
dden, sharp turns or aggressive lane changes. Failure to follow any of these
warnings may result in loss of control of the vehicle, leading to an accident and
serious injury or death.
Page 98 of 200
GOODYEAR® DUNLOP® TIRES
97
Always maintain inflation pressure at the level recommended by the vehicle
manufacturer as shown on the vehicle placard, vehicle certification label or in the vehicle
Owner’s Manual:
Underinflation is the leading cause of tire failure and may result in severe cracking,
c o
mponent separation or “blowout.” It reduces tire load capacity, allows excessive
sidewall flexing and increases rolling resistance, resulting in heat and mechanical
damage. Maintaining proper inflation pressure is the single most important thing you can
do to promote tire durability and maximize tread life.
Overinflation increases stiffness, which may deteriorate ride and generate unwanted
vi
bration. Overinflation also increases the chances of impact damage.
DON’T OVERLOAD YOUR VEHICLE
Check your vehicle Owner’s Manual to determine the load limits. Overloading your vehicle
places stress on your tires and other critical vehicle components. Overloading a vehicle can
cause poor handling or increased fuel consumption and may cause tire failure. Overloading
your tires can result in severe cracking, component separation or “blowout.”
Never fit your vehicle with new tires that have less load capacity than shown on the
ve
hicle tire placard and remember that optimum rim width is important for proper tire
load distribution and function. The maximum load capacity stamped on the sidewalls of
P-Metric & European Metric tires is reduced by 10% when used on a light truck, utility
vehicle or trailer. Never fit P-Metric or European Metric tires to light trucks that specify
LT-type replacement tires.
DO NOT SPIN YOUR TIRES EXCESSIVELY
Avoid excessive tire spinning when your vehicle is stuck in snow, ice, mud or sand. The
centrifugal forces generated by a free-spinning tire/wheel assembly may cause sudden
tire explosion, resulting in vehicle damage and/or serious personal injury to you or a
bystander. Never exceed 35 mph (55 km/h), as indicated on your speedometer. Use a
g e
ntle backward and forward rocking motion to free your vehicle for continued driving.
Never stand near or behind a tire spinning at high speeds, for example, while attempting
to push a vehicle that is stuck or when an on-the-car spin balance machine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when they reach 2/32 of an inch remaining tread
depth. All new tires have tread wear indicators which appear as smooth banks in the
tread grooves when they wear to the 2/32 of an inch level. Many wet weather accidents
result from skidding on bald or nearly bald tires. Excessively worn tires are also more
susceptible to penetrations.
Page 100 of 200
GOODYEAR® DUNLOP® TIRES
99
DO NOT MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE SAME AXLE
For optimum handling and control, Goodyear® recommends fitment of four tires of the
same type and size unless otherwise specified by the vehicle manufacturer.
When replacing tires, you must maintain the outside diameter and load-carrying capacity
of
the Original Equipment tire. Inflation pressure may need to be adjusted to avoid
overloading the tire. Consult the Tire & Rim Association Load and Inflation Tables,
European Tire and Rim Technical Organization (ETRTO) or Japan Automobile Tyre
Manufacturers Association (JATMA) standards for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-CARRYING CAPACITY THAN
RE
QUIRED BY THE ORIGINAL EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load Range E tires as
d e
signated by the vehicle manufacturer. Fitment of a tire, such as a Load Range D, with
less carrying capacity is not allowed. In other cases, tires of the same size may carry
different load indexes in the service description. You must make certain the replacement
tires fitted to the vehicle have a load-carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.
NOTE:
Goodyear® manufactured and/or marketed European- Metric passenger tires and
P -
Metric passenger tires are interchangeable as long as they have the same section
width, same aspect ratio, same rim diameter.
FOLLOW THESE ADDITIONAL GUIDELINES
When installing only two tires, fit the tires with the deepest tread depth on the rear axle.
If radials and non-radials must be fitted to the same vehicle, fit radials on rear axle. Never
mix radials and non-radials on the same axle. When fitting winter tires or all-season tires
WARNING!
Before you replace your tires, always consult the vehicle owner’s manual and follow
the vehicle manufacturer’s replacement tire recommendations. Vehicle handling may
be significantly affected by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional installer in order to
make certain that proper clearance, load-carrying capacity and inflation pressure are
selected. Never exceed the maximum load capacity and inflation pressure listed on
the sidewall of the tire. Always drive safely and obey all traffic laws. Avoid sudden,
sharp turns or aggressive lane changes. Failure to follow this warning may result in
loss of control of the vehicle, leading to an accident and serious injury or death.
CAUTION!
Never substitute a “Standard Load” (SL) tire for an Extra Load (XL) or Reinforced tire. If
the vehicle was originally equipped with “Extra Load” (XL) or Reinforced tires, replace
those tires with similar-sized Extra Load (XL) or Reinforced tires.
Page 102 of 200
GOODYEAR® DUNLOP® TIRES
101
TIRE SERVICE LIFE
Tires are designed and built to provide many thousands of miles/kilometers of excellent
service. For maximum benefit, tires must be maintained properly to avoid tire damage
that may result in removal from service before the tread is worn down to minimum depth.
It is not practical to accurately predict the service life of any specific tire in chronological
t i
me since service conditions vary widely. The serviceability of a tire over time is a
function of the storage and service conditions (inflation pressure, load, speed, road
hazard injury, etc.) to which a tire is subjected. Consumers should not rely solely on the
appearance of the tire, but should be aware of any change in dynamic performance such
as increased air loss, noise or vibration, which could be a sign to remove the tire.
Therefore, it is essential to have tires, including spares, inspected regularly (at least
monthly) for proper inflation pressure, damage and treadwear.
Check your vehicle’s Owner’s Manual (or your vehicle) to determine if it is equipped with
r u
n-flat (extended mobility) tires. If your vehicle is equipped with run-flat tires, the
following applies:
RUN-FLAT TECHNOLOGY EXTENDED MOBILITY TECHNOLOGY (EMT™), RUNONFLAT®
( R
OF) AND DUNLOP® SELF-SUPPORTING TECHNOLOGY (DSST®) ORIGINAL EQUIPMENT
TIRES
IMPORTANT SAFETY INFORMATION
OPERATIONAL MONITORING
The information contained in this Limited Warranty Brochure applies only to the Original
E q
uipment tires supplied with your vehicle. In order for Goodyear® Run-Flat (Extended
Mobility Technology [EMT], RunOnFlat [ROF]) or Dunlop® Run-Flat (Dunlop® Self-
Supporting Technology [DSST]) tires to obtain the performance criteria stated within this
Limited Warranty, Goodyear® or Dunlop® Run-Flat tires must use specific parts, such as
a low tire pressure monitoring system authorized by the Original Equipment vehicle
manufacturer.
RUN-FLAT TIRE FEATURE:
The Goodyear® or Dunlop® Run-Flat tire is a high-performance tire with a remarkable
f e
ature: It can operate for limited distances with very low or even no inflation pressure
(refer to your Vehicle Owner’s Manual for these limitations). This is an important benefit,
especially if inflation loss occurs at a location where immediately stopping your vehicle
could be hazardous.
TIRE PRESSURE MONITORING SYSTEM ALERT:
Refer to your vehicle Owner’s Manual for more information on what to do if the tire
p r
essure warning system activates.
Page 103 of 200
GOODYEAR® DUNLOP® TIRES
102
TO PROLONG TIRE LIFE DURING A SYSTEM ALERT
The Goodyear® or Dunlop® Run-Flat tire can be driven at low or zero air pressure (refer
to your vehicle Owner’s Manual for these limitations). To help prolong the life of a tire
operating in underinflation conditions, drive at a speed as far below 50 mph (80 km/h)
a s
possible. Also, drive the shortest distance possible before obtaining tire service.
Taking these precautions will increase the chance that your tire will be repairable.
SERVICE AFTER A SYSTEM ALERT®
To obtain service after operating under low-inflation conditions, contact your Goodyear®
or Dunlop Run-Flat service facility. Trained service personnel will inspect your tires to
determine if they are in need of repair or replacement. To locate the nearest authorized
Goodyear® or Dunlop® Run-Flat service facility, call 1-800- GOODYEAR
1-800-466-3932.
TIRE REPAIR
Like any other Goodyear® or Dunlop® speed-rated, high-performance tire, the
Goodyear® or Dunlop® Run-Flat tire may be repaired to correct a puncture in the tread,
but PROPER MATERIALS AND PROCEDURES MUST BE USED. Contact a Goodyear® or
Dunlop® Run-Flat service facility for information on proper repairs. For the location of the
nearest facility, call 1-800-GOODYEAR 1-800-466-3932.
WARNING!
If the tire pressure-monitoring system signals an alert, follow these safety precautions
to prevent a loss of vehicle control that could result in serious personal injury or death:
• S low your speed. Do not exceed 50
mph (80 kph).
• A void hard cornering, hard braking and severe handling maneuvers.
•
Avoid potholes and other road hazards.
R
emember that when your tires have lost air pressure, your vehicle’s handling
c a
pability is reduced, particularly during severe maneuvers.
WARNING!
Because of the unique characteristics of Run-Flat tires, the wheels on which they are
mounted and your vehicle’s tire pressure monitoring system, all tire service work other
than routine inflation maintenance and external inspections must be performed by
service personnel at a Goodyear® or Dunlop® Run-Flat service facility.
Do not attempt to mount or demount Run-Flat tires yourself; serious injury or death
co
uld result. Only specially trained persons should mount, demount and repair
Run-Flat tires, and more than 40 psi (270 kPa) may be required to seat beads. A safety
cage and clip-on extension air hose must be used if more than 40 psi (270 kPa) is
need to seat beads.