light DODGE JOURNEY 2010 1.G Manual PDF

“ILLUMIN Approach”
When this feature is selected, the headlights will activate
and remain on for up to 90 seconds when the doors are
unlocked with the RKE transmitter. To make your selec-
tion, press and hold the RESET button until “Off,”
“30 sec,” “60 sec,” or “90 sec” appears.
Display ECO — If Equipped
The “ECO” message can be turned on or off. To make
your selection, press and release the FUNCTION SE-
LECT button until “ON” or “OFF” appears.
“Display Units In”
The EVIC, odometer, and navigation system (if
equipped) can be changed between English and Metric
units of measure. To make your selection, press andrelease the RESET button until “ENGLISH” or “MET-
RIC” appears.
“NAV Turn By Turn” — If Equipped
When ON is selected, the Turn-by-Turn directions will
appear in the display as the vehicle approaches a desig-
nated turn within a programmed route. To make your
selection, press and release the RESET button until “ON”
or “OFF” appears.
Compass Variance
Refer to “Compass Variance” under “Compass Display.”
Calibrate Compass
Refer to “Manual Compass Calibration” under “Com-
pass Display.”
4
UNDERSTANDING YOUR INSTRUMENT PANEL 213

SETUP Button
Pressing the SETUP button allows you to select between
the following items:
NOTE:Turn the TUNE/SCROLL control knob to scroll
through the entries. Push the AUDIO/SELECT button to
select an entry and make changes.
•DVD Enter - When the disc is in DVD Menu mode,
selecting DVD Enter will allow you to play the current
highlighted selection. Use the remote control to scroll
up and down the menu (if equipped).
•DISC Play/Pause - You can toggle between
playing the DVD and pausing the DVD by
pushing the SELECT button (if equipped).
•DVD Play Options - Selecting the DVD Play Options
will display the following:
•Subtitle – Repeatedly pressing SELECT will switch
subtitles to different subtitle languages that are
available on the disc (if equipped).
•Audio Stream – Repeatedly pressing SELECT will
switch to different audio languages (if supported on
the disc) (if equipped).
•Angle – Repeatedly pressing SELECT will change
the viewing angle if supported by the DVD disc (if
equipped).
NOTE:
•The available selections for each of the above entries
varies depending upon the disc.
•These selections can only be made while playing a
DVD.
•VES™ Power - Allows you to turn VES™ ON and
OFF (if equipped).
4
UNDERSTANDING YOUR INSTRUMENT PANEL 219

An auxiliary input jack permits passengers to listen to a
portable MP3 player through the vehicle’s speakers. For
vehicles equipped with the Video Entertainment System
(VES)™, separate audio outputs allow passengers to
listen to the vehicle speakers while different audio tracks
play through the system’s wireless headphones. This
means rear-seat passengers can watch a DVD on the
optional rear-seat entertainment system while the driver
and front-seat passenger listen to the radio.
Other special features include music type selections,
traffic messaging (optional), easy store presets, parental
lockout for VES™ (if equipped), and a backup camera
display for vehicles equipped with a backup camera.
Refer to your “Navigation User’s Manual” for detailed
operating instructions.Operating Instructions — Uconnect™ Multimedia
(Satellite Radio)
Refer to your “Navigation User’s Manual” for detailed
operating instructions.
Operating Instructions — Uconnect™ Phone
Refer to your “Navigation User’s Manual” for detailed
operating instructions.
Clock Setting Procedure
The GPS receiver in this system is synchronized to the
time data being transmitted by the GPS satellites. The
satellites’ clock is Greenwich Mean Time (GMT). This is
the worldwide standard for time. This makes the sys-
tem’s clock very accurate once the appropriate time zone
and daylight savings information is set.
252 UNDERSTANDING YOUR INSTRUMENT PANEL

Changing the Time Zone
NOTE:You can skip Steps 2 and 3 by pressing and
holding the “TIME” button on the radio for three sec-
onds.
1. Turn on the multimedia system.
2. Press and release the “SETUP” button on the radio.
3. If “Time Setup” is highlighted on the menu, press and
release the joystick in the center of the radio. Otherwise,
turn the knob surrounding the joystick to select “Time
Setup,” and then press and release the joystick.
4. Turn the knob surrounding the joystick to scroll to
“Time Zone,” and then press and release the joystick.
5. If the desired time zone setting has a check mark next
to it, proceed to the next step. Otherwise, turn the knob surrounding the joystick to select the desired time zone
setting, and then press and release the joystick. A check
mark will display next to the selection.
6. Press and release the “SETUP” button to exit the
screen.
Changing Daylight Savings Time
When On is selected, this feature will display the time of
day in daylight savings time. Proceed as follows to
change the current setting:
NOTE:
You can skip Steps 2 and 3 by pressing and
holding the “TIME” button on the radio for three sec-
onds.
1. Turn on the multimedia system.
2. Press and release the “SETUP” button on the radio.
3. If “Time Setup” is highlighted on the menu, press and
release the joystick in the center of the radio. Otherwise,4
UNDERSTANDING YOUR INSTRUMENT PANEL 253

turn the knob surrounding the joystick to select “Time
Setup,” and then press and release the joystick.
4. Turn the knob surrounding the joystick to scroll to
“Daylight Savings,” and then press and release the
joystick.
5. If the desired setting has a check mark next to it,
proceed to the next step. Otherwise, turn the knob
surrounding the joystick to select “Off” or “On,” and
then press and release the joystick. A check mark will
display next to the selection.
6. Press and release the “SETUP” button to exit the
screen.
Setting the User Clock
If you wish to set the clock to a time different from the
system clock, you can manually adjust the time by
performing the following:NOTE:
You can skip Steps 2 and 3 by pressing and
holding the “TIME” button on the radio for three sec-
onds.
1. Turn on the multimedia system.
2. Press and release the “SETUP” button on the radio.
3. If “Time Setup” is highlighted on the menu, press and
release the joystick in the center of the radio. Otherwise,
turn the knob surrounding the joystick to select “Time
Setup,” and then press and release the joystick.
4. If “User Time” has a check mark next to it, proceed to
the next step. Otherwise, turn the knob surrounding the
joystick to scroll to “User Time,” and then press and
release the joystick.
5. Turn the knob surrounding the joystick to select “Set
Hours,” and then press and release the joystick.
254 UNDERSTANDING YOUR INSTRUMENT PANEL

6. Turn the knob surrounding the joystick to set the hour
highlighted on the clock on the screen. Press and release
the joystick when done.
7. Turn the knob surrounding the joystick to select “Set
Minutes,” and then press and release the joystick.
8. Turn the knob surrounding the joystick to set the
minutes highlighted on the clock on the screen. Press and
release the joystick when done.
9. Press and release the “SETUP” button to exit the
screen.
Show Time if Radio is Off
When selected, this feature will display the time of day
on the screen when the system is turned off. Proceed as
follows to change the current setting:
NOTE:You can skip Steps 2 and 3 by pressing and
holding the “TIME” button on the radio for three sec-
onds. 1. Turn on the multimedia system.
2. Press and release the “SETUP” button on the radio.
3. If “Time Setup” is highlighted on the menu, press and
release the joystick in the center of the radio. Otherwise,
turn the knob surrounding the joystick to select “Time
Setup,” and then press and release the joystick.
4. Turn the knob surrounding the joystick to scroll to
“Clock if Radio off,” and then press and release the
joystick to change the current setting. A check mark will
display next to “Clock if Radio off” when the feature is
selected.
5. Press and release the “SETUP” button to exit the
screen.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 255

Tune/Scroll Knob
In the List mode, the Tune/Scroll knob functions in a
similar manner as the scroll wheel on the iPod.
Turning the Tune/Scroll knob clockwise (forward) and
counterclockwise (backward) scrolls through lists, dis-
playing the track detail on the radio display. Once the
track to be played is highlighted on the radio display,
press the Tune/Scroll knob to select and start playing the
track. By turning the Tune/Scroll knob fast, the device
will jump through the list faster. During fast scroll, a
slight delay in updating the information on the radio
display may be noticed.
During all List modes, the iPodwill display all lists in
“wrap-around” mode. So if the track to be selected is at
the bottom of the list, just turn the Tune/Scroll knob
backward (counterclockwise) to get to the track faster. Radio Preset Buttons
In the List mode, the radio preset buttons are used as
shortcuts to the following lists on the iPod
device.
•1 – Playlists
•2 – Artists
•3 – Albums
•4 – Genres
•5 – Audiobooks
•6 – Podcasts
After pressing a preset button, the list selected is on the
top line and the first item in that list on the second line.
To exit the List mode without selecting a track, press the
same preset button again to go back to Play mode.
266 UNDERSTANDING YOUR INSTRUMENT PANEL

3. Do not apply paper or tape to the disc; avoid scratch-
ing the disc.
4. Do not use solvents such as benzene, thinner, cleaners,
or anti-static sprays.
5. Store the disc in its case after playing.
6. Do not expose the disc to direct sunlight.
7. Do not store the disc where temperatures may become
too high.
NOTE:If you experience difficulty in playing a particu-
lar disc, it may be damaged (i.e., scratched, reflective
coating removed, a hair, moisture or dew on the disc)
oversized, or have protection encoding. Try a known
good disc before considering disc player service.RADIO OPERATION AND CELLULAR PHONES
Under certain conditions, the cellular phone being on in
your vehicle can cause erratic or noisy performance from
your radio. This condition may be lessened or eliminated
by relocating the cellular phone antenna. This condition
is not harmful to the radio. If your radio performance
does not satisfactorily “clear” by the repositioning of the
antenna, it is recommended that the radio volume be
turned down or off during cellular phone operation.
CLIMATE CONTROLS
The Climate Control System allows you to regulate the
temperature, amount, and direction of air circulating
throughout the vehicle. The controls are located in the
center stack of the instrument panel.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 269

•In order to prevent fogging, when the RECIRCULA-
TION button is pressed and the mode control is set to
PANEL, the A/C will engage automatically.
•The A/C can be deselected manually without disturb-
ing the mode control selection.
Economy Mode
If ECONOMY mode is desired, press the A/C button to
turn off the indicator light and the A/C compressor.
Rotate the temperature control knob to the desired
temperature.
Air Conditioning Operation
Push on this button to engage the Air
Conditioning (A/C). A light will illu-
minate when the A/C System is en-
gaged.
NOTE: The air conditioning compressor will not engage
until the engine has been running for about 10 seconds.
Max A/C
For maximum cooling use the A/C and RECIRCULA-
TION mode buttons at the same time.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 273

Manual Operation
This system offers a full complement of manual override
features. The AUTO symbol in the front ATC display will
be turned off when the system is being used in the
manual mode.
NOTE:Each of these features operate independently
from each other. If any one feature is controlled manually,
the temperature doors will continue to operate automati-
cally.
The blower fan speed can be set to any fixed speed by
pressing the Front Upper ATC Panel blower rocker
button. The fan will now operate at a fixed speed until
additional speeds are selected. This allows the front
occupants to control the volume of air circulated in the
vehicle and cancel the AUTO mode.
The operator can also select the direction of the airflow
by selecting one of the following positions. Panel Mode
Air is directed through the outlets in the instrument
panel. These outlets can be adjusted for direction,
and turned on or off to control airflow.
NOTE: For maximum airflow to the rear, the center
instrument panel outlets can be directed toward the rear
seat passengers.
Bi-Level Mode Air comes from the instrument panel outlets, floor
outlets and defrost outlets. A slight amount of air is
also directed through the side window demister outlets.
NOTE: In many temperature positions, the BI-LEVEL
mode is designed to provide cooler air out of the panel
outlets and warmer air from the floor outlets.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 281