bulb DODGE JOURNEY 2013 1.G User Guide

is heard and press the TRIP ODOMETER button to turn
off the message. If the problem persists, the message will
appear the next time the vehicle is started.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the MIL.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing.Normally, the OBD II system will be ready. The OBD II
system maynotbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over.
3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part
of a normal bulb check.
528 MAINTAINING YOUR VEHICLE

CavityCar-
tridge
FuseMini-
FuseDescription
F182 50 Amp
RedCabin Heater #3 –
If Equipped
F184 30 Amp
PinkFront Wiper Motor
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
Interior Bulbs
Bulb Number
Courtesy/Reading
Lamps (Incandescent)578
Courtesy/Reading
Lamps (Optional LED)LED (Serviced at
Authorized Dealer)
Glove Box Lamp 194
Cargo Lamp 579
Optional Door Map
Pocket/CupholderLED (Serviced at
Authorized Dealer)
For lighted switches, see your authorized dealer for
replacement instructions.
572 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
Low Beam Headlamp 9006
High Beam Headlamp 9005
Front Park/Turn Signal 3757AK
Side Marker Lamp 168
Front Fog Lamp PSX24W
Center High Mounted
Stop Lamp (CHMSL)LED (Serviced at
Authorized Dealer)
License Lamp 168
Exterior Bulbs – Rear (LED Version)
Bulb Number
Rear Tail/Stop Lamp LED (Serviced at
Authorized Dealer)
Rear Tail (Liftgate) Lamp LED (Serviced at
Authorized Dealer)
Rear Turn Signal Lamp WY21W
Backup Lamp W21W
Exterior Bulbs – Rear (Bulb Version)
Bulb Number
Rear Tail/Stop Lamp P27/7W
Rear Tail (Liftgate) Lamp P27/7W
Rear Turn Signal Lamp PY27/7W
Backup Lamp P27/7W
7
MAINTAINING YOUR VEHICLE 573

BULB REPLACEMENT
Front Low/High Beam Headlamp, Turn
Signal/Park Lamp, And Side Marker Lamp
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the Totally Integrated Power
Module (TIPM) aside to replace certain lamps in the left
headlamp housing.
2. Rotate the applicable bulb and connector assembly ¼
turn counterclockwise and remove the assembly from
the headlamp housing.
3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
1 — Front Turn Signal/Park Lamp Bulb
2 — Side Marker Lamp Bulb
3 — Low Beam Headlamp Bulb
4 — High Beam Headlamp Bulb 574 MAINTAINING YOUR VEHICLE

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlamp housing and rotate it ¼ turn clockwise to
lock it in place.
Front Fog Lamp
NOTE:Turn the steering wheel to the right if replacing
the left front fog lamp or to the left if replacing the right
front fog lamp to allow for easier access to the front of the
wheel well.
1. Remove the fasteners retaining the front lower wheel
well access panel and remove the access panel.2. Remove the electrical connector from the fog lamp
housing.
3. Squeeze the two tabs on the side of the bulb socket and
pull straight out from the fog lamp.
7
MAINTAINING YOUR VEHICLE 575

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
4. Install the replacement bulb and connector assembly
straight into the fog lamp until it locks into place.
5. Reinstall the front lower wheel well access panel and
fasteners.
Rear Turn Signal And Backup Lamp
The taillamps are a two-piece design. The tail/stop/rear
turn signal lamps are located in the rear corner body
panels. The tail and backup lamps are located in the
liftgate.
Changing The Rear Turn Signal Lamp
1. Open the liftgate.
2. Remove the two fasteners from the inboard side of the
taillamp housing.
576 MAINTAINING YOUR VEHICLE

3. Carefully insert a trim stick (plastic flat-blade tool)
between the body panel and the outboard side of the
taillamp housing with one hand and grasp the flange
on the inboard side of the taillamp housing with the
other hand. Use the trim stick and hand pressure
together to disengage the taillamp housing from the
vehicle.
4. Rotate the applicable bulb’s electrical connector ¼ turn
counterclockwise and remove it from the taillamp
housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
taillamp housing and rotate the connector ¼ turn
clockwise to lock it in place.
7. Reinstall the taillamp housing and fasteners.Changing The Backup Lamp
1. Open the liftgate.
2.
Remove the two fasteners retaining the taillamp hous-
ing to the liftgate from the inboard face of the liftgate.
7
MAINTAINING YOUR VEHICLE 577

3. Carefully insert a trim stick (plastic flat-blade tool)
between the taillamp housing and the liftgate. Use the
trim stick and hand pressure together to disengage the
taillamp housing from the liftgate.4. Rotate the applicable bulb’s electrical connector ¼ turn
counterclockwise and remove it from the housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
housing and rotate the connector ¼ turn clockwise to
lock it in place.
7. Reinstall the taillamp housing and fasteners.
578 MAINTAINING YOUR VEHICLE

License Plate Lamp
1. Push the small locking tab sticking out of the end of
the lens toward the side of the vehicle and hold it in
that position.2. Insert a small flat-blade tool between the end of the
lens with the locking tab and the surrounding housing
and then pivot the tool to separate the lens from the
housing.
3. Hold the lens with one hand and rotate the bulb’s
electrical connector ¼ turn counterclockwise with the
other hand and then separate the bulb and connector
assembly from the lens.
4. Remove the bulb from the connector socket and install
the replacement bulb.
5. Install the bulb and connector assembly into the lens
and rotate the connector ¼ turn clockwise to lock it in
place.
6. Insert the end of the lens without the locking tab into
the housing on the liftgate and then push the opposite
end of the lens into the housing, making sure it locks
in the housing.
License Lamp
7
MAINTAINING YOUR VEHICLE 579

Bulb Replacement.........................572
Bulbs, Light.............................108
Camera, Rear............................245
Capacities, Fluid..........................580
Caps, Filler
Fuel.................................477
Oil (Engine)...........................525
Power Steering.........................421
Radiator (Coolant Pressure)................550
Carbon Monoxide Warning..................105
Cargo Area Cover.........................280
Cargo Area Features.......................277
Cargo Compartment.......................277
Light................................277
Luggage Carrier........................286
Cargo Load Floor.........................278Cargo Management System..................278
Rollaway Tonneau Cover..................280
Tri-Fold Load Floor......................278
Cargo Tie-Downs.........................279
Cargo (Vehicle Loading)....................278
Car Washes.............................560
Cellular Phone...........................368
Certification Label.........................479
Chains, Tire.............................456
Changing A Flat Tire.......................500
Chart, Tire Sizing.........................436
Check Engine Light (Malfunction Indicator Light) . .294
Checking Your Vehicle For Safety..............104
Checks, Safety...........................104
Child Restraint............................79
Child Safety Locks.........................33
Clean Air Gasoline........................469
608 INDEX