garage door opener DODGE JOURNEY 2015 1.G Owners Manual

!GARAGE DOOR OPENER — IF EQUIPPED . . .253
▫Before You Begin Programming HomeLink® . .255
▫Programming A Rolling Code.............256
▫Programming A Non-Rolling Code.........258
▫Canadian/Gate Operator Programming......259
▫Using HomeLink®....................261
▫Security............................261
▫Troubleshooting Tips...................261
▫General Information....................262
!POWER SUNROOF — IF EQUIPPED........263
▫Opening Sunroof — Express..............264
▫Opening Sunroof — Manual Mode.........264
▫Closing Sunroof — Express...............265
▫Closing Sunroof — Manual Mode..........265
▫Pinch Protect Feature...................265
▫Venting Sunroof — Express..............265
▫Sunshade Operation....................266
▫Wind Buffeting.......................266
▫Sunroof Maintenance...................266
▫Ignition Off Operation..................266
!ELECTRICAL POWER OUTLETS...........266
!POWER INVERTER — IF EQUIPPED........271
▫Power Inverter Operation................272
!CUPHOLDERS........................273
!STORAGE............................274
▫Glove Compartment...................274
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113

Power Sunroof Switch — If Equipped
Refer to “Power Sunroof” in “Understanding the Fea-
tures Of Your Vehicle” for further information.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink® replaces up to three remote controls (hand-
held transmitters) that operate devices such as garage
door openers, motorized gates, lighting or home security
systems. The HomeLink® unit operates off your vehicle’s
battery.
The HomeLink® buttons, located on either the overhead
console, headliner or sunvisor, designate the three differ-
ent HomeLink® channels. The HomeLink® indicator is
located above the center button.
Observation Mirror
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253

Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
1. Cycle the ignition to the ON/RUN position.
Training The Garage Door Opener
1—DoorOpener2 — Training Button
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink® button you wish to pro-
gram while keeping the HomeLink® indicator light in
view.
3. Push and hold the HomeLink® button you want to
program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi-
cator light. The HomeLink® indicator will flash slowly
and then rapidly after HomeLink® has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.
5. At the garage door opener motor (in the garage),
locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor.
Firmly push and release the “LEARN” or “TRAIN-
ING” button. On some garage door openers/devices
there may be a light that blinks when the garage door
opener/device is in the LEARN/TRAIN mode.
NOTE:You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed
HomeLink® button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE:If the garage door opener/device does not acti-
vate, push the button a third time (for two seconds) to
complete the training.
To program the remaining two HomeLink® buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257

Reprogramming A Single HomeLink® Button
(Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink® button until
the indicator light begins to flash after 20 seconds.Do
not release the button.
3.Without releasing the buttonproceed with “Program-
ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to
8 cm) away from the HomeLink® button you wish to
program while keeping the HomeLink® indicator
light in view.
3. Push and hold the Homelink® button you want to
program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi-
cator light. The Homelink® indicator will flash slowly
and then rapidly after HomeLink® has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.
5. Push and hold the programmed HomeLink® button
and observe the indicator light.
•If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink® button is pushed.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Place the hand-held transmitter 1 to 3 inches (3 to
8 cm) away from the HomeLink® button you wish to
program while keeping the HomeLink® indicator
light in view.
3. Continue to push and hold the HomeLink® button,
while you push and release (“cycle”) your hand-held
transmitter every two seconds until HomeLink® has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.
4. Watch for the HomeLink® indicator to change flash
rates. When it changes, it is programmed. It may take
up to 30 seconds or longer in rare cases. The garage
door may open and close while you are programming.
5. Push and hold the programmed HomeLink® button
and observe the indicator light.
•If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink® button is pushed.
•To program the two remaining HomeLink® buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink® Button
(Canadian/Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink® button until
the indicator light begins to flash after 20 seconds.Do
not release the button.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3.Without releasing the buttonproceed with
“Canadian/Gate Operator Programming” step 2 and
follow all remaining steps.
Using HomeLink®
To operate, push and release the programmed
HomeLink® button. Activation will now occur for the
programmed device (i.e., garage door opener, gate opera-
tor, security system, entry door lock, home/office light-
ing, etc.,). The hand-held transmitter of the device may
also be used at any time.
Security
It is advised to erase all channels before you sell or turn
in your vehicle.
To do this, push and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink® Universal Transceiver is disabled when
the Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink®,
here are some of the most common solutions:
•Replace the battery in the original hand-held transmit-
ter.
•Push the LEARN button on the Garage Door Opener
to complete the training for a Rolling Code.
•Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.comfor information or assistance.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261

WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run your vehicle in the garage while
programming the transceiver. Exhaust gas can cause
serious injury or death.
WARNING!
Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people, pets
or other objects are in the path of the door or gate.
Only use this transceiver with a garage door opener
that has a “stop and reverse” feature as required by
Federal safety standards. This includes most garage
door opener models manufactured after 1982. Do not
(Continued)
WARNING!(Continued)
use a garage door opener without these safety fea-
tures. Call toll-free 1–800–355–3515 or, on the Internet
at www.HomeLink.com for safety information or
assistance.
General Information
This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause unde-
sired operation.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Door Opener, Garage.......................253
Driving
Through Flowing, Rising, or Shallow Standing
Water................................427
Driving to Achieve Maximum Fuel Economy......316
DVD Player (Video Entertainment System™)......347
E-85 Fuel...............................485
Electrical Outlet, Auxiliary (Power Outlet)........266
Electrical Power Outlets.....................266
Electric Remote Mirrors.....................117
Electronic Brake Control System...............434
Brake Assist System.....................437
Traction Control System...................437
Electronic Roll Mitigation (ERM)..............438
Electronic Speed Control (Cruise Control)........236
Electronic Stability Control (ESC)..............439
Electronic Vehicle Information Center
Instrument Cluster Display.................27
Electronic Vehicle Information Center (EVIC)......307
Remote Start...........................27
Emergency, In Case of
Freeing Vehicle When Stuck................532
Hazard Warning Flasher..................511
Jacking...............................514
Jump Starting..........................528
Overheating...........................511
Towing..............................535
Emission Control System Maintenance..........544
Engine.................................102
Air Cleaner...........................550
Block Heater..........................413
Break-In Recommendations................102
Checking Oil Level......................547
Compartment..........................541
Compartment Identification................542
Coolant (Antifreeze).....................561
Cooling..............................56110
INDEX 627

Requirements..........................480
Saver Mode...........................316
Specifications..........................598
Tank Capacity..........................597
Fuel, Flexible............................485
Fueling................................489
Fuel Optimizer...........................316
Fuel Saver..............................316
Fuel System Caution.......................490
Fuses..................................581
Garage Door Opener (HomeLink®)............253
Gas Cap (Fuel Filler Cap)...................489
Gasoline, Clean Air........................481
Gasoline (Fuel)
Conserving............................316
Gasoline, Reformulated.....................481
Gauges
Coolant Temperature.....................305
Fuel.................................305
Speedometer..........................305
Tachometer............................298
Gear Ranges.............................417
Gear Select Lever Override..................533
General Information.......................145
Glass Cleaning...........................580
Gross Axle Weight Rating...................492
Gross Vehicle Weight Rating..................492
GVWR.................................492
Hazard
Driving Through Flowing, Rising, or Shallow
Standing Water.........................427
Hazard Warning Flasher....................511
Headlights
Automatic............................223
Bulb Replacement.......................591
Cleaning.............................579
630 INDEX