fuse box DODGE NEON 1997 1.G Wiring Diagrams User Guide

Downloaded from www.Manualslib.com manuals search engine 8W-35 ANTI-LOCK BRAKES
INDEX
page page
DESCRIPTION AND OPERATION
ABS PUMP MOTOR RELAY................ 6
ABS SYSTEM RELAY..................... 6
ABS WARNING LAMP..................... 6
ANTI-LOCK BRAKES..................... 6BRAKE SWITCH INPUT................... 7
DATA LINK CONNECTOR.................. 7
HELPFUL INFORMATION.................. 7
HYDRAULIC MODULATOR................. 6
WHEEL SPEED SENSORS................. 7
DESCRIPTION AND OPERATION
ANTI-LOCK BRAKES
Power for the Anti-Lock brake system is supplied
by two fuses. There is a 15 amp fuse located in the
fuse block cavity 10. This fuse supplies power to the
Controller Anti Lock Brake (CAB), and the ABS sys-
tem relay on the F12 circuit. The F12 circuit also
supplies power to the Powertrain Control Module
(PCM). Power for the fuse is supplied on the A21 cir-
cuit from the ignition switch. This fuse is HOT in the
START/RUN position.
The second fuse is located in the Power Distribu-
tion Center (PDC). It is a 40 amp fuse. This fuse is
HOT at all times and supplies power to the contact
side of the ABS pump motor relay.
There are three grounding points used in the ABS
system. One is a case ground on the CAB. The sec-
ond is the Z12 circuit at the CAB connector cavity 5.
This ground is spliced, and terminates at the left side
of the radiator closure panel.
The third ground is on the Z1 circuit. This ground
is used for the ABS hydraulic modulator, ABS system
relay, and the ABS pump motor. This ground, like the
Z12 ground splices and terminates at the left head-
lamp ground.
Additional information on the circuit function of
the ABS system is listed below. For diagnostic and
testing procedures, refer to the appropriate section of
the Service Manual or the Diagnostic Test Proce-
dures Manual.
ABS WARNING LAMP
The ABS warning lamp is an output from the Con-
troller Anti Lock Brake (CAB) and the ABS relay
box. It is used to alert the operator of a problem in
the ABS system. The G19 circuit from the CAB and
the ABS system relay is used to detect a problem. If
a problem is detected, the CAB grounds the G19 cir-
cuit and illuminates the lamp in the instrument clus-
ter.
Circuit G19 is also an output of the CAB to the
ABS system relay contact side.
ABS SYSTEM RELAY
The system relay is used for the operation of the
ABS system. Power for the relay is supplied on the
B57 circuit from cavity 57 of the Controller Anti Lock
Brake (CAB).
Ground for the relay is on the Z1 circuit. This
ground is spliced in with the pump motor and termi-
nates at the left headlamp ground.
When the system is operating normally power for
the contact side of the relay is supplied from the
CAB on the B57 circuit. It passes through the relay
to the Z1 ground and terminates at the left headlamp
ground. If a problem is detected in the system, the
contact side of the relay switches from the Z1 to the
F12 circuit. This causes the ABS warning lamp in
the instrument cluster to illuminate.
ABS PUMP MOTOR RELAY
The ABS pump motor relay controls when the
pump motor runs. Power for the coil side of the relay
is supplied from cavity 47 of the Controller Anti Lock
Brake (CAB) on the B47 circuit. This circuit also sup-
plies voltage for the contact side of the system relay.
The ground side of the coil is controlled by the B116
circuit. Circuit B116 connects to cavity 16 of the CAB
connector.
Circuit B120 from cavity 20 of the CAB connector
powers the ABS pump motor. This circuit is also used
as an input to the CAB for pump motor monitoring.
HYDRAULIC MODULATOR
The hydraulic modulator is used for the controlling
of the brake system pressure to the wheels. The mod-
ulator is made up of four solenoids.
Circuits involved are, B142 for the left front wheel,
B143 for the right front wheel, B146 for the left rear
wheel, and B148 for the right rear wheel.
The solenoids use a common ground on the Z1 cir-
cuit. There are two Z1 circuits from the modulator.
Both of these grounds terminate at the left headlamp
ground, and are spliced in with the ABS pump motor
and the ABS system relay.
8W - 35 - 6 8W - 35 ANTI-LOCK BRAKESPL

Downloaded from www.Manualslib.com manuals search engine 8W-40 INSTRUMENT CLUSTER
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 7
Component Page
ABS Relay Box......................8W-40-5
Airbag Control Module................8W-40-5
Airbag Warning Lamp.................8W-40-5
Anti-Lock Warning Lamp..............8W-40-5
Brake Warning Lamp.................8W-40-5
Brake Warning Lamp Switch...........8W-40-5
Charge Indicator Lamp................8W-40-5
Check Engine Lamp..................8W-40-6
Cluster Illumination Lamps............8W-40-2
Controller Anti-Lock Brake.............8W-40-5
Engine Coolant Temperature Gauge......8W-40-6
Engine Coolant Temperature Sensor......8W-40-6
Engine Oil Pressure Switch............8W-40-6
Fuel Gauge.........................8W-40-6
Fuel Pump Module...................8W-40-6
Fuse 9 (FB).........................8W-40-2
Fuse 11 (FB)........................8W-40-6
Fuse 13 (PDC).......................8W-40-3
Fuse Block........................8W-40-2, 6
G101..............................8W-40-5
G204..............................8W-40-6
Headlamp Dimmer And Optical
Horn Switch......................8W-40-2
Headlamp Switch..................8W-40-2, 3
High Beam Indicator Lamp.............8W-40-2
Instrument Cluster...........8W-40-2, 3, 4, 5, 6
Key-In Switch.......................8W-40-3Component Page
Left Front Door Jamb Switch...........8W-40-3
Left Park/Turn Signal Lamp............8W-40-4
Left Repeater Lamp..................8W-40-4
Left Turn Indicator Lamp..............8W-40-4
Low Oil Pressure Lamp...............8W-40-6
Park Brake Switch...................8W-40-5
Power Distribution Center.............8W-40-3
Powertrain Control Module.........8W-40-3, 5, 6
Right Park/Turn Signal Lamp...........8W-40-4
Right Repeater Lamp.................8W-40-4
Right Turn Indicator Lamp.............8W-40-4
S107..............................8W-40-5
S112 ..............................8W-40-4
S116 ..............................8W-40-4
S127..............................8W-40-5
S201..............................8W-40-6
S203..............................8W-40-3
S207..............................8W-40-4
S208..............................8W-40-5
S209..............................8W-40-2
S210..............................8W-40-2
S212..............................8W-40-4
Seat Belt Warning Lamp...............8W-40-5
Turn Signal/Hazard Switch.............8W-40-4
Vehicle Speed Sensor..................8W-40-3
8W - 40 - 2 8W - 40 INSTRUMENT CLUSTERPL

Downloaded from www.Manualslib.com manuals search engine 8W-44 INTERIOR LIGHTING
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 5
Component Page
Ash Receiver Lamp...................8W-44-4
Dome Lamp.........................8W-44-2
Fuse 2 (FB).........................8W-44-4
Fuse 9 (FB).........................8W-44-4
Fuse 13 (PDC)...................8W-44-2, 3, 4
Fuse Block.........................8W-44-4
G204............................8W-44-2, 4
Glove Box Lamp And Switch..........8W-44-2, 4
Headlamp Switch..................8W-44-2, 4
Left Front Door Ajar Switch............8W-44-2
Left Rear Door Ajar Switch.............8W-44-2
Left Visor/Vanity Lamps...............8W-44-3
Map/Reading Lamps................8W-44-2, 4
Mercury Switch......................8W-44-3
Power Distribution Center.........8W-44-2, 3, 4Component Page
PRNDL Lamp.......................8W-44-4
Right Front Door Ajar Switch...........8W-44-2
Right Rear Door Ajar Switch............8W-44-2
Right Visor/Vanity Lamps..............8W-44-3
S201..............................8W-44-4
S202..............................8W-44-2
S203..........................8W-44-2, 3, 4
S210..............................8W-44-4
S220............................8W-44-2, 4
S304..............................8W-44-2
S309............................8W-44-3, 4
Trunk Lamp........................8W-44-2
Trunk Switch.......................8W-44-2
Underhood Lamp....................8W-44-3
8W - 44 - 2 8W - 44 INTERIOR LIGHTINGPL

Downloaded from www.Manualslib.com manuals search engine SWITCH AJAR
DOOR
FRONT
LEFT RIGHT
FRONT
DOOR
AJAR
SWITCH
LEFT
REAR
DOOR
AJAR
SWITCH
SWITCH AJAR
DOOR
REAR
RIGHT
S304
13FUSE10A
BATT A0
M1
18
PK
M2
20
YLM2
20
YLM2
20
YLM2
20
YL
M1
20
PK
M1
22
PK
13C103
3C105
21
M1
22
PK
1
3
M2
20
YL
M4
22
GY/BK
M4
18
GY/BK
TRUNK
SWITCH
3C309
S220
1
NO
CONNECTIONM2
22
YL
3
SWITCH HEADLAMP
M2
22
YL
Z1
22
BK
Z1
2O
BK
S202
G204
1
AND LAMP
BOX
GLOVE
M1
22
PK
M1
22
PK
S203
DOME
LAMP LAMP TRUNK
M2
20
YL
12C230
CENTER DISTRIBUTION
POWER
13 14
SWITCH
A
M23
22
YL
M2
22
YL
MAP/
READING
LAMPS
2C225
(8W-10-8)(8W-10-4)
(8W-50-2)
(8W-15-7)
(8W-15-7) (8W-10-8)(8W-10-4)
(8W-44-4)(8W-44-4)
8W - 44 - 2 8W-44 INTERIOR LIGHTINGPL-RHD
978W-1PLR04401

Downloaded from www.Manualslib.com manuals search engine BATT A0
POWER
DISTRIBUTION
CENTER
13 73
10A
FUSE
13 2FUSE
15A
1
22
BATT A3
BLOCK FUSE
299
4A
FUSE
9
1
HEADLAMP
SWITCH
0 OFF
1 PARK
2 HEAD
4
F33
20
PK/RDE1
20
TN
13C103
M1
18
PK
M1
22
PK
1
2
GLOVE
BOX
LAMP
AND
SWITCH
Z3
20
BK/OR
S203
M1
22
PK
BK/OR20 Z3
LAMP PRNDL
21
OR22 E2 E2
22
OR
1
2
Z3
20
BK/OR
E2
20
OR
Z3
14
BK/OR
G204
LAMP RECEIVER
ASH S210
S201
2
1 0
LAMPS READING
MAP/
B
Z3
18
BK/OR
Z3
20
BK/OR
3C225
S220
M2
22
YL
M23
22
YL/BK
2C225
1NO
CONNECTION
M2
22
YL
M1
22
PK
E2
22
OR
1C203
Z3
20
BK/OR
2C203
M1
18
PK
M1
18
PK
1C225
S309
CA (8W-10-4)
(8W-10-8) (8W-11-4)(8W-11-2)
(8W-11-11)
(8W-50-2)
(8W-10-8)
(8W-15-7)(8W-11-11)
(8W-15-7) (8W-10-6) (8W-10-4)
(8W-44-2)
(8W-10-8)
8W - 44 - 4 8W-44 INTERIOR LIGHTINGPL-RHD
978W-1PLR04403

Downloaded from www.Manualslib.com manuals search engine 8W-44 INTERIOR LIGHTING
INDEX
page page
DESCRIPTION AND OPERATION
ASH RECEIVER LAMP.................... 6
DOME LAMP............................ 5
GLOVE BOX LAMP....................... 6
HALO LAMP/TIME DELAY RELAY............ 5
HELPFUL INFORMATION.................. 6
INTRODUCTION......................... 5MAP/READING LAMPS.................... 6
PRNDL (TRANSMISSION RANGE INDICATOR)
LAMP................................ 5
TIME OUT RELAY........................ 5
TRUNK LAMP........................... 6
UNDERHOOD LAMP...................... 6
VISOR/VANITY LAMPS.................... 5
DESCRIPTION AND OPERATION
INTRODUCTION
The courtesy lamp system is powered at all times
by the 10 amp fuse located in the Power Distribution
Center (PDC). The M1 circuit feeds the courtesy
lamps, which include the trunk lamp, underhood
lamp, visor/vanity lamps, dome lamp, time delay
relay, and the glove box lamp.
HALO LAMP/TIME DELAY RELAY
The time delay relay is used to allow a time-ON
function for the ignition switch halo lamp. Power for
the relay is received on the M1 circuit from the 10
amp fuse located in the Power Distribution Center
(PDC). This is the Ignition-Off Draw (IOD) fuse and
HOT at all times.
When a door is OPENED, or the headlamp switch
is moved to the dome lamp position, a ground path is
provided for the relay on the M23 circuit. This ener-
gizes the relay, CLOSING the contacts. When the
relay contacts are CLOSED, power is provided
through the relay to the M50 circuit.
The M50 circuit supplies current to the ignition
switch lamp in the steering column. Ground for the
lamp is provided on the Z3 circuit. This circuit
splices with the glove box lamp, the ash receiver
lamp, and the PRNDL lamp. The Z3 circuit termi-
nates at the instrument panel left center support.
Circuit M23 is also spliced with the Remote Key-
less Entry (RKE) module and the time out relay
located in the fuse block.
TIME OUT RELAY
The time out relay is located in the fuse block and
is used to control the ground path for various interior
lamps. It will also turn the lamps OFF after a spec-
ified period of time, and works with the Remote Key-
less Entry (RKE) system for illuminated entry.
Cirucit M2 connects to the relay and supplied a
ground path through the door ajar switches.Circuit M1 is used to supply battery voltage to the
relay. This circuit is proteced by a 10 amp fuse
located in cavity 13 of the Power Distribution Center
(PDC).
Circuit M32 is connected from the relay to the var-
ious interior lamps and RKE module.
PRNDL (TRANSMISSION RANGE INDICATOR)
LAMP
The PRNDL lamp receives power on the E2 circuit
from the 4 amp fuse located in the fuse block in cav-
ity 12. The fuse receives power from the headlamp
switch. Circuit E2 also powers the ash receiver lamp.
When the headlamp switch is moved to the PARK
or ON position, current flows through the fuse to the
PRNDL lamp. The ground for the lamp is supplied
on the Z3 circuit, and terminates at the instrument
panel left center support. This circuit is also spliced
in with the ash receiver lamp, the ignition switch
lamp, and the glove box lamp.
VISOR/VANITY LAMPS
The visor/vanity lamps are case-grounded, and are
operated by a switch internal to the assembly. Power
for the lamps is on the M1 circuit from the Power
Distribution Center (PDC). When the operator opens
the cover, the switch CLOSES, completing a path to
ground illuminating the lamp.
DOME LAMP
The dome lamp receives power from the 10 amp
fuse located in the Power Distribution Center on the
M1 circuit. This circuit is HOT at all times and the
Ignition-Off Draw (IOD) fuse. The ground path for
the lamp is provided in two different ways.
One way is through the door ajar switches and the
time out relay. Circuit M2 connects to all the door
ajar switches from the time out relay. The switches
are case-grounded to the body. When a door is
OPENED, the plunger in the switch CLOSES, com-
pleting a path to ground.
PL8W - 44 INTERIOR LIGHTING 8W - 44 - 5

Downloaded from www.Manualslib.com manuals search engine The second ground path is through the headlamp
switch. Circuit M23 is spliced in with the time out
relay. When the operator turns the headlamp switch
to the dome lamp ON position, a ground path is pro-
vided through the switch on the Z1 circuit. This
ground terminates at the instrument panel left cen-
ter support.
On vehicles equipped with Remote Keyless Entry
(RKE) the M23 circuit is spliced to the RKE module.
This allows the lamp to be turned ON when a valid
signal is reveived by the RKE module from the trans-
mitter.
MAP/READING LAMPS
The map/reading lamps are powered by the M1 cir-
cuit from the Power Distribution Center (PDC). This
circuit is the Ignition-Off Draw circuit and protected
by a 10 amp fuse. The M1 circuit is spliced and pro-
vides power for the visor/vanity lamps, radio, power
mirrors, dome lamp, time delay relay, and other inte-
rior lamps.
Ground for the lamps is provided from two sources.
One is the Z3 circuit which is spliced in with the
glove box lamp and terminates at the instrument
panel left center support. The second ground is pro-
vided on circuit M23. This circuit is spliced in with
the time out relay so the lamps will turn ON when
any door is OPENED.
On vehicles equipped with Remote Keyless Entry
(RKE) the M23 circuit, which is the ground circuit
when a door is OPENED, is connected to the RKE
module. The module will provide a ground path for
the lamps with a valid signal from the transmitter.
GLOVE BOX LAMP
The glove box lamp receives power on the M1 cir-
cuit from the 10 amp fuse located in the Power Dis-
tribution Center (PDC). A switch, wired in series
after the lamp, CLOSES when the glove box door is
opened, and completes a path to ground on the Z3
circuit.
The Z3 circuit is spliced in with the ash receiver
lamp, PRNDL lamp, and the time delay relay. The Z3
circuit terminates at the instrument panel left center
support.
ASH RECEIVER LAMP
The ash receiver lamp receives power on the E2
circuit from the 4 amp fuse located in the fuse block
in cavity 12. The fuse receives power from the head-
lamp switch. Circuit E2, which is HOT at all times,
also powers the Transmission Range Indicator
(PRNDL) lamp.
When the headlamp switch is moved to the PARK
or ON position, current flows through the fuse to the
ash receiver lamp. The ground for the lamp is sup-
plied on the Z3 circuit, and terminates at the instru-
ment panel left center support. This circuit is also
spliced in with the PRNDL lamp, the ignition switch
lamp, and the glove box lamp.
UNDERHOOD LAMP
Power for the underhood lamp is supplied on cir-
cuit M1. This is the Ignition-Off Draw (IOD) circuit
and is protected by a 10 amp fuse located in the
Power Distribution Center (PDC).
When the hood is raised a ground path is com-
pleted through the mercury switch to a case ground
illuminating the lamp.
TRUNK LAMP
The trunk lamp uses a case-grounded switch
located on the trunk latch. The switch is normally
OPEN. When the deck lid is opened, the switch
CLOSES, completing a path to ground on circuit M4.
The M1 circuit provides power to the lamp, and is
HOT at all times.
HELPFUL INFORMATION
²Check the 10 amp fuse located in the Power Dis-
tribution Center (PDC) for the trunk lamp, under-
hood lamp, visor/vanity lamps, dome lamp, time
delay relay, and the glove box lamp.
²Check for a good ground at the instrument panel
left center support.
²Check the door switches for a good ground.
²Check the 4 amp fuse in the fuse block, cavity
12.
8W - 44 - 6 8W - 44 INTERIOR LIGHTINGPL
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine 8W-47 AUDIO SYSTEMS
INDEX
page page
DESCRIPTION AND OPERATION
HELPFUL INFORMATION.................. 5
RADIO ILLUMINATION.................... 5RADIO MEMORY........................ 5
RADIO OPERATION...................... 5
SPEAKERS............................. 5
DESCRIPTION AND OPERATION
RADIO OPERATION
When the ignition switch is in either the ACCES-
SORY or RUN position, it connects circuit A1 from
the Power Distribution Center (PDC) to circuit A31.
Circuit A31 powers a bus bar in the fuse block. The
bus bar feeds two circuits, one of which is circuit
X12. Circuit X12 powers the radio. A 10 amp fuse, in
cavity 16 of the fuse block, protects circuit X12.
Circuit Z9 supplies the ground path for the radio.
The grounding point for circuit Z9 is the instrument
panel right center support.
RADIO MEMORY
Circuit M1 from the Power Distribution Center
(PDC) supplies power for the radio memory. The cir-
cuit contains the Ignition Off Draw (IOD) fuse. The
IOD fuse is removed during vehicle shipping to pre-
vent excessive battery draw.
RADIO ILLUMINATION
When the parking lamps or headlamps are ON, cir-
cuits E2 and L7 power the radio illumination lamps
and park lamps. Circuit E2 feeds the illumination
lamp. Circuit L7 feeds the park lamps of the radio.
Circuit F33 feeds circuit L7.
A 4 amp fuse, in cavity 12 of the fuse block, pro-
tects circuit E2. A 15 amp fuse, in cavity 2 of the fuse
block, protects circuits L7 and F33.
SPEAKERS
Circuit X53 feeds the speaker in the left front door.
Circuit X55 is the return from the speaker to the
radio. On the premium system the X53 and X55 cir-
cuits are connected in with the instrument panel
speaker.
Circuit X54 feeds the speaker in the right front
door. Circuit X56 is the return from the speaker to
the radio. On the premium system the X54 and X56
circuits are connected in with the instrument panel
speaker.
Circuit X51 feeds the left rear speaker. Circuit X57
is the return from the speaker to the radio.Circuit X52 feeds the right rear speaker. Circuit
X58 is the return from the speaker to the radio.
HELPFUL INFORMATION
²Circuit M1 also powers the vanity lamps, glove
box lamp, time delay relay, dome lamps, underhood
lamp, cargo lamp, and power mirrors.
²If the radio does not operate, check for blown
fuses in circuits A1 and X12.
²Circuits A3, and F33 feed the L7 circuit.
²If the radio illumination lamps do not operate,
check for blown fuses in circuits E2, F33, and A3.
PL8W - 47 AUDIO SYSTEMS 8W - 47 - 5

Downloaded from www.Manualslib.com manuals search engine 978W-1
8W - 80 - 5 PL-RHD 8W-80 CONNECTOR PIN-OUTS
PLR08005
CAV CIRCUIT FUNCTION
1 C22 20DB/WT LOW PRESSURE SWITCH OUTPUT
2 C21 20DB/OR A/C CYCLING SWITCH OUTPUT
A/C LOW
PRESSURE SWITCH
BLACK
12
CAV CIRCUIT FUNCTION
1 B142 20BR/YL LEFT FRONT DUMP SOLENOID CONTROL
2 B143 20DG/YL RIGHT FRONT DUMP SOLENOID CONTROL
3 B146 20BR/LB LEFT REAR DUMP SOLENOID CONTROL
4 B148 20DB/LB RIGHT REAR DUMP SOLENOID CONTROL
5 Z1 18BK GROUND
6 Z1 18BK GROUND
BLACK
CAV CIRCUIT FUNCTION
1 F12 18DG/WT ABS RELAY FEED
2 Ð Ð
3 B116 20GY ABS PUMP MOTOR RELAY CONTROL
4 B57 20BR/BK ABS SYSTEM RELAY CONTROL
5 A20 12RD/DG FUSED B(+)
6 B120 12BR/WT ABS PUMP MOTOR RELAY OUTPUT
7 G19 20LG/BR ABS WARNING LAMP DRIVER
8 Ð Ð
9 B47 20RD/LB ABS SYSTEM RELAY OUTPUT
10 Z1 14BK GROUND
DARK
GRAY
ABS HYDRAULIC
MODULATOR 31
64
ABS RELAY BOX 51
10 6
CAV CIRCUIT FUNCTION
1 R45 18DG/LB DRIVER AIRBAG SQUIB LINE 2
2 R43 18BK/LB DRIVER AIRBAG SQUIB LINE 1
3 R47 18DB/LB LEFT IMPACT SENSOR LINE 1
4 R49 18LB LEFT IMPACT SENSOR LINE 2
5 R42 18BK/YL PASSENGER AIRBAG SQUIB LINE 1
6 R44 18DG/YL PASSENGER AIRBAG SQUIB LINE 2
7 R46 18BR/LB RIGHT IMPACT SENSOR LINE 1
8 R48 18TN RIGHT IMPACT SENSOR LINE 2
9 R41 18BK/TN AIRBAG WARNING LAMP DRIVER
10 Z6 18BK/PK GROUND
11 R50 18BR/YL PASSENGER AIRBAG PRESSURE SWTICH SENSE
12 R51 18VT/YL PASSENGER AIRBAG PRESSURE SWITCH GROUND
17 F15 18DB/WT FUSED IGNITION SWITCH OUTPUT (RUN/START)
18 D2 20WT/BK CCD BUS (Ð)
19 D1 20VT/BR CCD BUS (+)
20 F25 18TN/LG FUSED IGNITION SWITCH OUTPUT (RUN)
11 1
22 12
AIRBAG CONTROL
MODULEYELLOW

Downloaded from www.Manualslib.com manuals search engine 978W-1
8W - 80 - 17 PL-RHD 8W-80 CONNECTOR PIN-OUTS
PLR08017
CAV CIRCUIT FUNCTION
1 Z1 18BK GROUND
2 Z2 18BK GROUND
3 G4 18DB FUEL LEVEL SENSOR SIGNAL
4 A141 18DG/WT FUEL PUMP RELAY OUTPUT
LT GRAY
FUEL PUMP
MODULE 41
BLACK
CAV CIRCUIT FUNCTION
1 A142 18DG/OR AUTOMATIC SHUTDOWN RELAY OUTPUT
2 K20 18DG GENERATOR FIELD DRIVER
GENERATOR 21
CAV CIRCUIT FUNCTION
1 M1 22PK FUSED B(+)
2 Z3 20BK/OR GROUND12
GLOVE BOX
LAMP AND SWITCHGRAY
HEADLAMP DIMMER
AND OPTICAL HORN
SWITCH 41BLACK
CAV CIRCUIT FUNCTION
1 L4 14VT/WT DIMMER SWITCH LOW BEAM OUTPUT
2 L2 14LG HEADLAMP SWITCH OUTPUT
3 L3 14RD/OR DIMMER SWITCH HIGH BEAM OUTPUT
4 L20 14LG/WT FUSED B(+)
BLACK
HEADLAMP
SWITCH 1
2
9
73
4
5
6 8
CAV CIRCUIT FUNCTION
1 E1 20TN PANEL LAMPS DIMMER SWITCH SIGNAL
2 L2 14LG HEADLAMP SWITCH OUTPUT
3 M2 22YL TIME OUT RELAY
4 F33 20PK/RD FUSED B(+)
5G26 20LB KEY-IN IGNITION SWITCH SENSEG26 20LB KEY-IN IGNITION SWITCH SENSE
6G16 20BK/LB LEFT FRONT DOOR JAMB SWITCH SENSEG16 20BK/LB LEFT FRONT DOOR JAMB SWITCH SENSE
7 L20 14LG/WT FUSED B(+)
8 A3 12RD/WT FUSED B(+)
9L7 20BK/YL PARK LAMP SWITCH OUTPUT
L7 20BK/YL PARK LAMP SWITCH OUTPUT
CAV CIRCUIT FUNCTION
1Ð Ð
2 L43 20VT LEFT HEADLAMP FEED
3 Z1 20BK GROUND
4 E2 20OR ILLUMINATION FEED
5 L13 20BR/YL HEADLAMP LEVELING SIGNAL TO MOTORSHEADLAMP LEVELING
SWITCH
12 345
BLACK