garage door opener DODGE NITRO 2007 1.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2007, Model line: NITRO, Model: DODGE NITRO 2007 1.GPages: 436, PDF Size: 1.68 MB
Page 79 of 436
▫To Set At A Desired Speed...............126
▫To Deactivate........................126
▫To Resume Speed.....................126
▫To Vary The Speed Setting...............126
▫Manual Transmission..................127
▫To Accelerate For Passing...............127
Electronic Brake Control System............128
▫ABS (Anti-Lock Brake System)............128
▫TCS (Traction Control System)............129
▫BAS (Brake Assist System)...............129
▫ERM (Electronic Roll Mitigation)..........130
▫ESP (Electronic Stability Program).........131
▫ESP/BAS Warning Lamp................134Garage Door Opener — If Equipped.........134
▫Programming The Universal Transceiver.....136
▫“Rolling Code” Programming............138
▫Canadian Programming/Gate Programming . . 139
▫Operation...........................140
▫Reprogramming A Single Button..........140
▫Security............................140
Power Sunroof — If Equipped.............141
▫Opening Sunroof - Express..............142
▫Closing Sunroof - Express...............142
▫Pinch Protect Feature...................142
▫Pinch Protect Override.................143
▫Venting Sunroof - Express...............143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
3
Page 134 of 436
situation requiring ESP to be switched to the “Partial Off”
mode is overcome, turn ESP back on by momentarily
depressing the “ESP OFF” switch. This may be done
while the vehicle is in motion.
ESP/BAS Warning Lamp
The malfunction indicator lamp for the ESP is
combined with BAS. The “ESP/BAS Warning
Lamp” and the “ESP/TCS Indicator Light” in
the instrument cluster both come on when the
ignition switch is turned to the “ON” position. They
should go out with the engine running. If the “ESP/BAS
Warning Lamp” comes on continuously with the engine
running, a malfunction has been detected in either the
ESP or the BAS system. If this light remains on after
several ignition cycles, and the vehicle has been driven
several miles at speeds greater than 30 mph (48 km/h),
see your authorized dealer as soon as possible to have the
problem diagnosed and corrected.NOTE:
•TheESP/TCS Indicator Lightand theESP/BAS
Warning Lampcome on momentarily each time the
ignition switch is turned ON.
•Each time the ignition is turned ON, the ESP System
will be ON even if it was turned off previously.
•The ESP Control System will make buzzing or clicking
sounds when it is active. This is normal; the sounds
will stop when ESP becomes inactive following the
maneuver that caused the ESP activation.
GARAGE DOOR OPENER — IF EQUIPPED
NOTE:The HomeLinksystem will be disabled if the
Vehicle Theft Alarm (if equipped) is in the Prearmed,
Armed or Alarming state. The HomeLinksystem will
only operate when the Vehicle Theft Alarm (if equipped)
is in the Disarmed mode.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 135 of 436
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at the
push of a button. The Universal Transceiver operates off
your vehicle’s battery and charging system; no batteries
are needed.For additional information on HomeLink, call 1–800–
355–3515, or on the internet at www.homelink.com.
WARNING!
A moving garage door can cause injury to people and
pets in the path of the door. People or pets could be
seriously or fatally injured. Only use this transceiver
with a garage door opener that has a “stop and
reverse” feature as required by federal safety stan-
dards. This includes most garage door opener mod-
els manufactured after 1982. Do not use a garage
door opener without these safety features it could
cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety
information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135
3
Page 136 of 436
Programming The Universal Transceiver
For best results, install a new battery in the hand held
transmitter before programming. If your garage door
opener (located in the garage) is equipped with an antenna,
make sure that the antenna is hanging straight down.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle’s exhaust while
training the transceiver. Exhaust gas can cause seri-
ous injury or death.
WARNING!
Your motorized door or gate will open and close
while you are training the Universal Transceiver. Do
not train the transceiver if people or pets are in the
path of the door or gate. A moving door or gate can
cause serious injury or death to people and pets or
damage to objects.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 137 of 436
1. Turn off the engine.
2. Erase the factory test codes by pressing the two
outside buttons. Release the buttons when the light in the
Universal Transceiver begins to flash (about 20 seconds).
NOTE:Do not repeat Step 2 to program additional hand
held transmitters.
3. Choose one of the three Universal Transceiver buttons
to program. Place the hand held controller one to three
inches from the Universal Transceiver while keeping its
indicator light in view.
4. Using both hands, press the hand held transmitter
button and the desired Universal Transceiver button. Do
not release the buttons until step 5 has been completed.
NOTE:Some entry gates and garage door openers may
require you to replace step 4 with the procedures listed
under Canadian Programming.
HomeLink Buttons
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
3
Page 138 of 436
5. The indicator light in the Universal Transceiver will
begin to flash, first slowly and then rapidly. The rapid
flashing indicates successful programming. If after 90
seconds the indicator light does not flash rapidly or goes
out, return to step 1 and repeat the procedure. To train the
other buttons, repeat steps 3 and 4. Be sure to keep your
hand held transmitters in case you need to retrain the
Universal Transceiver.
NOTE: If you do not successfully program the Uni-
versal Transceiver to learn the signal of your hand held
transmitter, refer to the Rolling Code Paragraph, or call
toll free for customer assistance at 1–800–355–3515, or
on the internet at www.homelink.com.
“Rolling Code” Programming
NOTE:If your hand held transmitter appears to pro-
gram the Universal Transceiver, but your garage door or
other device does not operate, and your device wasmanufactured after 1996, your garage door opener or
other device may have a “Rolling Code” system.
On garage door openers with the “Rolling Code” feature,
the transmitter code changes after each use to prevent the
copying of your code.
To check if your device is protected by a “Rolling Code”
system:
•Check the owner’s manual for the device for mention
of “Rolling Codes”.
•Press and hold the programmed button on the Univer-
sal Transceiver. If the Universal Transceiver indicator
light flashes rapidly and then stays on after 2 seconds,
the device has the “Rolling Code” feature.
To train a garage door opener (or other rolling code
equipped devices) with the rolling code feature, follow
these instructionsaftercompleting theProgramming
portion of this text:
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 139 of 436
NOTE:The assistance of a second person may make the
following programming procedure quicker and easier.
1. Locate the training button on the garage door motor
head unit. The exact location and color of the button may
vary by garage door opener manufacturer. If you have
difficulty in locating the training button, check your
garage door opener manual, or call 1-800-355-3515 or, on
the Internet, at www.homelink.com.
2. Press and hold the training button on the garage door
opener head unit. This will activate the “training” light.
NOTE:After completing step 2, you have 30 seconds to
start step 3.
3. Return to the Universal Transceiver in the vehicle and
firmly press and release the garage door button. Press
and release the button a second time to complete thetraining process. Some garage door openers may require
you to do this procedure a third time to complete the
training.
Your garage door opener should now recognize your
Universal Transceiver. The remaining two buttons may
now be programmed if this has not previously been
done. Refer to the Programming instructions. You may
use either your Universal Transceiver or your original
hand-held transmitter to open you garage door.
Canadian Programming/Gate Programming
Canadian frequency laws, and the technology of some
entry gates, require you to press and release the hand
held transmitter button every two seconds during pro-
gramming.
Continue to press and hold the Universal Transceiver
button while you press and release the hand held trans-
mitter button until the frequency signal has been learned.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
3
Page 140 of 436
The Universal Transceiver light will flash slowly and
then rapidly when the programming is successful.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Operation
Press and hold the desired button on the Universal
Transceiver until the garage door or other device begins
to operate. The light in the display shows that the signal
is being transmitted. The hand held transmitter may also
be used at any time.
Reprogramming A Single Button
1. Press and hold the Universal Transceiver button to be
reprogrammed. Do not release until step 4 has been
completed.2. When the indicator light begins to flash slowly (after
20 seconds) position the hand held transmitter one to
three inches away from the button to be trained.
3. Press and hold the hand held transmitter button.
4. The Universal Transceiver indicator light will begin to
flash, first slowly, then rapidly. When the indicator lights
begin to flash rapidly, release both buttons.
Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously trained frequencies, hold
down both outside buttons until the indicator light
begins to flash.
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
1. This device may not cause harmful interference.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 374 of 436
Cavity Cartridge
FuseMini
FuseDescription
M10 20 Amp
YellowIgnition Off Draw —
Vehicle Entertainment
System (IOD-VES),
Satellite Digital Audio
Receiver (SDARS),
DVD, Hands Free
Module (HFM), RA-
DIO, Antenna (ANT),
Universal Garage
Door Opener
(UGDO), Vanity
Lamp (VANITY LP)
M11 10 Amp
Red(Ignition Off Draw)
IOD-HVAC/ATC,
MW SENSR, Under-
hood Lamp (UH
LMP)Cavity Cartridge
FuseMini
FuseDescription
M12 30 Amp
GreenAmplifier (AMP)
M13 20 Amp
YellowIgnition Off Draw—
Cabin Compartment
Node (IOD-CCN),
Wireless Control
Module (WCM), SI-
REN, Clock Module
(CLK MOD), Multi-
Function Control
Switch (MULTIFCTN
SW)
M14 20 Amp
YellowTrailer Tow (Export
Only)
374 MAINTAINING YOUR VEHICLE
Page 423 of 436
Selection of Coolant (Antifreeze)......356,382,383
Temperature Gauge..................... 164
Corrosion Protection..................... 366
Crankcase Emission Control System.......... 350
CupHolder ............................ 147
Customer Assistance..................... 412
Data Recorder, Event...................... 61
Daytime Running Lights................... 122
Dealer Service.......................... 343
Defroster, Rear Window................... 156
Defroster, Windshield................ 76,230,231
Delay (Intermittent) Wipers................. 122
Diagnostic System, Onboard................ 340
Dimmer Switch, Headlight..............120,166
Dipsticks
Oil (Engine).......................... 343
Disposal
Engine Oil........................... 346Used Coolant (Antifreeze)................ 358
Door Locks............................. 27
Door Locks, Automatic.................... 30
Door Opener, Garage..................... 134
DriveBelts ............................ 347
Driving ............................... 262
DVD Player (Video Entertainment System)...... 225
Electric Remote Mirrors.................... 83
Electrical Outlet, Auxiliary (Power Outlet)...... 144
Electrical Power Outlets................... 144
Electronic Brake Control System............. 128
Electronic Speed Control (Cruise Control)...... 125
Electronic Stability Program (ESP).........131,166
Electronic Vehicle Information Center (EVIC).... 179
Emergency, In Case of
Hazard Warning Flasher................. 324
Jacking............................. 326
Towing ............................. 334
INDEX 423
10