remote start DODGE NITRO 2009 1.G Owners Manual

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A Word About Your Keys................. 12
▫Ignition Key Removal.................. 12
▫Key-In-Ignition Reminder................ 13
Sentry Key........................... 14
▫Replacement Keys..................... 15
▫Customer Key Programming............. 16
▫General Information.................... 17
Vehicle Security Alarm — If Equipped........ 17
▫To Arm The System.................... 18▫To Disarm The System.................. 18
Illuminated Entry....................... 19
Remote Keyless Entry.................... 19
▫To Unlock The Doors And Liftgate......... 20
▫To Lock The Doors And Liftgate........... 21
▫Express Down Window Feature —
If Equipped.......................... 22
▫Using The Panic Alarm................. 23
▫Programming Additional Transmitters....... 23
2

▫Battery Replacement................... 23
▫General Information.................... 24
Remote Starting System — If Equipped....... 25
Door Locks........................... 26
▫Manual Door Locks.................... 27
▫Power Door Locks..................... 28
▫Automatic Door Locks.................. 29
▫Automatic Unlock Doors On Exit.......... 30
▫Child-Protection Door Lock System (Rear
Doors)............................. 31
Windows............................. 32
▫Power Windows...................... 32
▫Wind Buffeting....................... 36Liftgate.............................. 36
Occupant Restraints..................... 37
▫Lap/Shoulder Belts.................... 38
▫Lap/Shoulder Belt Operating Instructions.... 39
▫Adjustable Upper Shoulder Belt Anchorage . . . 43
▫Automatic Locking Mode — If Equipped..... 44
▫Energy Management Feature............. 44
▫Enhanced Seat Belt Use Reminder System
(BeltAlert).......................... 45
▫Seat Belts And Pregnant Women........... 47
▫Seat Belt Extender..................... 47
▫Driver And Front Passenger Supplemental
Restraint Systems (SRS)................. 48
▫Child Restraint....................... 65
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE:
•The Sentry KeyImmobilizer System is not compat-
ible with some aftermarket remote starting systems.
Use of these systems may result in vehicle starting
problems and loss of security protection.
•Exxon/Mobil Speedpass™, additional Sentry Keys,
or any other transponder-equipped components on
the same key chain willnotcause a key-related
(transponder) fault unless the additional part isphysi-
cally held against the ignition keybeing used when
starting the vehicle. Cell phones, pagers, or other
Radio Frequency (RF) electronics will not cause inter-
ference with this system.
All of the keys provided with your new vehicle have
been programmed to the vehicle electronics.
Replacement Keys
NOTE:Only keys that are programmed to the vehicle
electronics can be used to start and operate the vehicle.
Once a Sentry Keyis programmed to a vehicle, it cannot
be programmed to any other vehicle.
CAUTION!
Always remove the Sentry Keysfrom the vehicle
and lock all doors when leaving the vehicle unat-
tended.
At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of keys. Du-
plication of keys may be performed at an authorized
dealer or by following the customer key programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
2

procedure. This procedure consists of programming a
blank key to the vehicle electronics. A blank key is one
that has never been programmed.
NOTE:When having the Sentry KeyImmobilizer
System serviced, bring all vehicle keys with you to an
authorized dealer.
Customer Key Programming
If you have two valid Sentry Keys, you can program
new Sentry Keysto the system by performing the
following procedure:
1. Cut the additional Sentry KeyTransponder blank(s)
to match the ignition switch lock cylinder key code.
2. Insert the first valid key into the ignition switch. Turn
the ignition switch to the ON position for at least three
seconds, but no longer than 15 seconds. Then, turn the
ignition switch to the LOCK position and remove the first
key.3. Insert the second valid key into the ignition switch.
Turn the ignition switch to the ON position within
15 seconds. After 10 seconds, a chime will sound. In
addition, the Vehicle Security Light will begin to flash.
Turn the ignition switch to the LOCK position and
remove the second key.
4. Insert a blank Sentry Keyinto the ignition switch.
Turn the ignition switch to the ON position within
60 seconds. After 10 seconds, a single chime will sound.
In addition, the Vehicle Security Light will stop flashing.
To indicate that programming is complete, the Vehicle
Security Light will turn on again for three seconds and
then turn off.
The new Sentry Keyis programmed.The Remote
Keyless Entry (RKE) transmitter will also be pro-
grammed during this procedure.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Arm the System:
Remove the keys from the ignition switch and exit the
vehicle. Lock the doors and liftgate by pressing the
power door LOCK switch or the LOCK button on the
Remote Keyless Entry (RKE) transmitter. Close all the
doors.
The Vehicle Security Light (located in the instrument
cluster) will flash rapidly for about 16 seconds to signal
that the system is arming. During this 16 second pre-arm
period, opening any door or the liftgate will cancel the
arming process. If the system arms successfully, the
Vehicle Security Light will flash at a slower rate to
indicate the alarm is set. Manually locking the doors with
the door lock plunger (located on the inside of the doors)
or the driver’s door key lock cylinder will not arm the
system.
To Disarm the System:
Either press the UNLOCK button on the RKE transmitter
or insert a valid Sentry Keyinto the ignition lock
cylinder and turn the key to the ON position.
The Vehicle Security Alarm system is designed to protect
your vehicle; however, you can create conditions where
the system will give you a false alarm. If the previously
described arming sequence has occurred, the system will
arm regardless of whether you are inside or outside the
vehicle. If you remain inside the vehicle and open a door,
the alarm will sound. If this occurs, disarm the system.
Manually unlocking the doors with the door lock plunger
(located on the inside of the doors) or the driver’s door
key lock cylinder will not disarm the system.
Tamper Alert
If something has triggered the Vehicle Security Alarm in
your absence, the horn will sound three times when you
unlock the doors. Check the vehicle for tampering.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

ILLUMINATED ENTRY
The interior lights come on when you open any door.
They will remain on for about 30 seconds after all doors
are closed then fade to off.
The lights also will fade to off if you turn on the ignition
after you close all the doors.
REMOTE KEYLESS ENTRY
This system allows you to lock or unlock the doors and
liftgate or activate the Panic Alarm from distances up to
23 ft (7 m) using your Remote Keyless Entry (RKE)
transmitter. The RKE transmitter does not need to be
pointed at the vehicle to activate the system.
NOTE:
•For the remote starting feature (if equipped), refer to
“Remote Starting System” in this section.
•Your vehicle’s RKE transmitter may have three or four
buttons depending on the optional features purchased
with your vehicle.
Three Button RKE transmitter
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
2

To Unlock the Doors and Liftgate
Press and release the UNLOCK button on the RKE
transmitter once to unlock the driver’s door, or twice to
unlock all doors and the liftgate. The parking lights will
flash to acknowledge the unlock signal. The illuminated
entry system will also turn on.
Remote Key Unlock, Driver Door/All Doors First
This feature lets you program the system to unlock either
the driver’s door or all doors and the liftgate on the first
press of the UNLOCK button on the RKE transmitter. To
change the current setting, proceed as follows:
On Electronic Vehicle Information Center (EVIC)
equipped vehicles, refer to “Remote Key Unlock,” under
“Personal Settings (Customer Programmable Features)”
under “Electronic Vehicle Information Center (EVIC)” in
Section 4.On non-EVIC equipped vehicles, perform the following
steps:
1. Press and hold the LOCK button on a programmed
(i.e., functional) RKE transmitter for at least four seconds,
but not longer than 10 seconds. Then, press and hold the
UNLOCK button while still holding the LOCK button.
2. Release both buttons at the same time.
3. Test the feature from outside the vehicle by pressing
the LOCK and UNLOCK buttons on the RKE transmitter.
4. Repeat these steps if you want to return this feature to
its previous setting.
NOTE:Pressing the LOCK button on the RKE transmit-
ter while you are inside the vehicle will activate the
Vehicle Security Alarm. Opening a door with the Vehicle
Security Alarm activated will cause the alarm to sound.
Press the UNLOCK button to deactivate the Vehicle
Security Alarm.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Flash Lights with Lock
The feature will cause the parking lights to flash when
the doors are locked or unlocked with the RKE transmit-
ter. This feature can be turned on or off. To change the
current setting, proceed as follows:
•On Electronic Vehicle Information Center (EVIC)
equipped vehicles, refer to “Flash Lights with Lock,”
underPersonal Settings (Customer Programmable
Features)” under “Electronic Vehicle Information Cen-
ter (EVIC)” in Section 4.
•On non-EVIC equipped vehicles, perform the follow-
ing steps:
1. Press and hold the UNLOCK button on a programmed
(i.e., functional) RKE transmitter for at least four seconds,
but not longer than 10 seconds. Then, press and hold the
LOCK button while still holding the UNLOCK button.
2. Release both buttons at the same time.3. Test the feature from outside the vehicle by pressing
the LOCK and UNLOCK buttons on the RKE transmitter.
4. Repeat these steps if you want to return this feature to
its previous setting.
NOTE:Pressing the LOCK button on the RKE transmit-
ter while you are inside the vehicle will activate the
Vehicle Security Alarm. Opening a door with the Vehicle
Security Alarm activated will cause the alarm to sound.
Press the UNLOCK button to deactivate the Vehicle
Security Alarm.Express Down Window Feature — If Equipped
This feature allows you to remotely lower both front door
windows at the same time. To use this feature, press and
release the UNLOCK button on the RKE transmitter and
then immediately press and hold the UNLOCK button
until the windows lower to the level desired or until they
lower completely.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
If your RKE transmitter fails to operate from a normal
distance, check for these two conditions:
1. Weak batteries in RKE transmitter. The expected life of
the batteries is from one to two years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.
REMOTE STARTING SYSTEM — IF EQUIPPED
Your vehicle may be equipped with a remote starting
system. This system allows the vehicle to be started from
distances up to 300 ft (91 m) using the Remote Keyless
Entry (RKE) transmitter, which is part of your ignition
key.
In order to start your vehicle remotely, the hood, liftgate,
and all of the doors must be closed.To start your vehicle remotely, press and release the
REMOTE START button on the RKE transmitter twice
within three seconds. To indicate that the vehicle is about
to start, the parking lights will flash and the horn will
sound briefly (if programmed).
Remote Start Button
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
2

Once the engine starts it will run for 15 minutes. To
cancel remote start, press and release the REMOTE
START button once.
To enter the vehicle while the engine is running during a
remote start, you must first unlock the vehicle using the
UNLOCK button on the RKE transmitter. Once the
vehicle is unlocked, you have 60 seconds to enter the
vehicle, insert the key in the ignition, and turn it to the
ON position. Otherwise, the system will cancel the
remote start and automatically turn off.
Remote start will also cancel if any of the following occur:
•If the engine stalls or RPM exceeds 2500.
•Any engine warning lamps come on.
•The hood is opened.
•The hazard switch is pressed.
•The transmission is moved out of PARK.The vehicle can be started remotely a maximum of two
times consecutively. The vehicle is also allowed a maxi-
mum of one failed start, where the remote start sequence
was initiated but the engine stopped cranking without
starting. Following either of these conditions, or if the
Vehicle Security Alarm (if equipped) is sounding, or if the
PANIC button was pressed, the system must be reset
before remote starting the vehicle again. To reset the
system, insert a valid key into the ignition and turn it to
the ON position and then back to the LOCK position.
DOOR LOCKS
The vacuum fluorescent (VF) display, located in the
odometer area, displays the word DOOR as an indication
of a door ajar or door not completely closed. When the
vehicle is not moving and the door is ajar or not
completely closed, the VF display will show the word
DOOR.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE