turn signal bulb DODGE POWER WAGON 2005 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2005, Model line: POWER WAGON, Model: DODGE POWER WAGON 2005 2.GPages: 455, PDF Size: 14.59 MB
Page 114 of 455
The arrow on either side of the instrument cluster flashes
to indicate the direction of the turn, and proper operation
of the front and rear turn signal lights. If a defective bulb
or wiring circuit is detected for the turn signal system, the
arrow indicators will flash at a faster rate. Also, the
LAMP OUTindicator in the instrument cluster will be
illuminated and a chime will be heard. If an indicator
fails to light when the lever is moved, it would suggest
that the switch or indicator lamp is defective.
You can signal a lane change by moving the lever
partially up or down.
Passing Light
You can signal another vehicle with your headlights by
partially pulling the multifunction lever toward the steer-
ing wheel. This will cause the high beam headlights to
turn on until the lever is released.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 163 of 455
20. Odometer/Trip Odometer
The odometer shows the total distance the vehicle has
been driven.
If the odometer reading is changed during repair or
replacement, be sure to keep a record of the reading
before and after the service so that the correct mileage can
be determined.
The trip odometer shows individual trip mileage. To
toggle between the odometer and the trip odometer,
press the Odometer/Trip Odometer Button. To reset the
Trip Odometer, press and hold the button while in trip
mode, until the Trip Odometer resets.
NOTE:There is also an engine hour function. This
indicates the number of hours the engine has been
running. To display the engine hours perform the follow-
ing: Place the ignition in RUN, but do not start the
engine. With the odometer value displayed, hold the trip
button down for a period of 6 seconds. The odometer willchange to trip value first, then it will display the engine
hour value. The engine hours will be displayed for a
period of 30 seconds until the ignition is turned off or the
engine is started.
21. TOW/HAUL (Automatic Transmissions Only)
The TOW/HAUL button is located at the end of the gear
shift lever. This light will illuminate when the TOW/
HAUL button has been selected.
22. LAMP OUT Light
The LAMP OUT indicator in the instrument cluster alerts
the driver if a defective bulb or wiring circuit is detected
for most of the exterior lamps - headlamps, turn signal
lamps, and stop lamps.
23. SERV 4WD Indicator
The 4WD indicator will be illuminated whenever the
4WD mode is engaged for either the manual or electric
shift 4WD systems. The SERV 4WD indicator monitors
the electric shift 4WD system. If the SERV 4WD light
UNDERSTANDING YOUR INSTRUMENT PANEL 163
4
Page 394 of 455
REPLACEMENT LIGHT BULBS
LIGHT BULBS—Inside Bulb No.
Overhead Console Lights............... TS212-2
Dome Light............................7679
All of the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved.
LIGHT BULBS—Outside Bulb No.
Back-Up..............................3057
Center High Mounted Stop Lamp............. 912
Fog Lamp...........................9006LL
Headlamp (Halogen)...................9007QL
Park & Turn Signal...................3157NAK
Rear License Plate Lamp................... 168
Rear Cargo Light......................... 912
Tail & Stop............................3057
BULB REPLACEMENT
Headlight (Halogen)/Front Park and Turn Lights
CAUTION!
This is a halogen bulb. Avoid touching the glass
with your fingers. Reduced bulb life will result.
394 MAINTAINING YOUR VEHICLE
Page 397 of 455
3. Pull the housing out from the fender to allow room to
disconnect the electrical connectors.4. Unlock and pull connector straight from the base of
the headlight halogen bulb.
5. Twist connector on turn signal/park light bulb
1⁄4turn
and remove connector and bulb from housing.
6. Remove housing from vehicle with headlight halogen
bulb in housing.
MAINTAINING YOUR VEHICLE 397
7
Page 398 of 455
7. Twist collar on headlight halogen bulb1⁄4turn and
remove headlight bulb from the housing.
8. Replace headlight or turn signal bulb. Do not touch
the headlight halogen bulb.
9. Reverse procedure for installation of bulbs and hous-
ing.
10. Tighten the outboard fastener first.
Tail, Stop, Turn and Backup Lights
1. Remove the two (2) screws that pass through the bed
sheetmetal.
398 MAINTAINING YOUR VEHICLE
Page 446 of 455
Infant Restraint.......................... 59
Inflation Pressure Tires.................... 304
Inside Rearview Mirror.................... 84
Instrument Cluster....................156,157
Instrument Panel and Controls.............. 155
Instrument Panel Lens Cleaning............. 392
Interior Appearance Care.................. 391
Intermittent Wipers...................... 116
Introduction............................. 4
Jack Location........................... 336
Jack Operation.......................... 338
Jump Starting.......................... 344
Key, Replacement........................ 14
Key, Sentry............................. 13
Key-In Reminder......................... 12
Keyless Entry System...................... 24
Keys................................12,18Lane Change and Turn Signals.............. 113
Lap Belts.............................. 44
Lap/Shoulder Belts....................... 36
LATCH (Lower Anchors and Tether for CHildren) . 63
Lights..............................74,109
Airbag............................58,158
Anti-Lock Warning..................162,284
Battery Saver......................... 111
Brake Warning........................ 162
Bulb Replacement...................... 394
Cap Top Clearance..................... 402
Center Mounted Stop................... 400
Check Engine......................... 157
Courtesy/Reading..................... 122
Cruise.............................. 161
Daytime Running...................... 112
Dual Wheel Assembly Rear............... 403
Fog ............................. 113,405
Four-Wheel Drive Indicator............... 280
446 INDEX