towing DODGE RAM 1500 1998 2.G User Guide

²Engine loads and temperatures are high such as
when towing a trailer.
²Cool silicone fluid within the fan drive unit is
being redistributed back to its normal disengaged
(warm) position. This can occur during the first 15
seconds to one minute after engine start-up on a cold
engine.
LEAKS
Viscous fan drive operation is not affected by small
oil stains near the drive bearing. If leakage appears
excessive, replace the fan drive unit.
VISCOUS DRIVE
If the fan assembly free-wheels without drag (the
fan blades will revolve more than five turns when
spun by hand), replace the fan drive. This spin test
must be performed when the engine is cool.
For the following test, the cooling system must be
in good condition. It also will ensure against exces-
sively high coolant temperature.
WARNING: BE SURE THAT THERE IS ADEQUATE
FAN BLADE CLEARANCE BEFORE DRILLING.
(1) Drill a 3.18-mm (1/8-in) diameter hole in the
top center of the fan shroud.
(2) Obtain a dial thermometer with an 8 inch stem
(or equivalent). It should have a range of -18É-to-
105ÉC (0É-to-220É F). Insert thermometer through the
hole in the shroud. Be sure that there is adequate
clearance from the fan blades.
(3) Connect a tachometer and an engine ignition
timing light. The timing light is to be used as a
strobe light. This step cannot be used on the diesel
engine.(4) Block the air flow through the radiator. Secure
a sheet of plastic in front of the radiator. Use tape at
the top to secure the plastic and be sure that the air
flow is blocked.
(5) Be sure that the air conditioner (if equipped)
and blowe fan is turned off.
WARNING: USE EXTREME CAUTION WHEN THE
ENGINE IS OPERATING. DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR
HANDS NEAR THE PULLEYS, BELTS OR FAN. DO
NOT WEAR LOOSE CLOTHING.
(6) Start the engine and operate at 2400 rpm.
Within ten minutes the air temperature (indicated on
the dial thermometer) should be up to 88É C (190É F).
Fan driveengagementshould start to occur at/be-
tween:
²3.7L Automatic - 93É C - 99ÉC (200É F - 210É F)
²3.7L Manual/4.7L Automatic/5.9L - 85É - 91É C
(185É - 195É F)
²4.7L Manual - 74É - 79É C (165É - 175É F)
²5.7L
²5.9L
²Engagement is distinguishable by a definite
increasein fan flow noise (roaring). The timing light
also will indicate an increase in the speed of the fan.
(7) When viscous drive engagement is verified,
remove the plastic sheet. Fan drivedisengagement
should start to occur at or between:
²3.7L Automatic - 76ÉC - 81ÉC (168É F - 178É F)
²3.7L Manual/4.7L Auto/ 5.9L - 67ÉC - 73ÉC (153É
F - 163É F)
²4.7L Manual - 56ÉC - 62ÉC (133É F - 143É F)
²5.7L
²5.9L
²8.0L engine - 93É to 101É C (190É - 205É F) Min-
imum 73ÉC (163ÉF). A definitedecreaseof fan flow
noise (roaring) should be noticed. If not, replace the
defective viscous fan drive unit.
CAUTION: Some engines equipped with serpentine
drive belts have reverse rotating fans and viscous
fan drives. They are marked with the word
REVERSE to designate their usage. Installation of
the wrong fan or viscous fan drive can result in
engine overheating.
Fig. 32 Viscous Fan Drive - Typical
1 - VISCOUS FAN DRIVE
2 - THERMOSTATIC SPRING
3 - MOUNTING NUT TO WATER PUMP HUB
DRENGINE 7 - 51
FAN DRIVE VISCOUS CLUTCH-GAS ENGINES (Continued)

CAUTION: If the viscous fan drive is replaced
because of mechanical damage, the cooling fan
blades should also be inspected. Inspect for fatigue
cracks, loose blades, or loose rivets that could
have resulted from excessive vibration. Replace fan
blade assembly if any of these conditions are
found. Also inspect water pump bearing and shaft
assembly for any related damage due to a viscous
fan drive malfunction.
FAN DRIVE VISCOUS CLUTCH
- 5.9L DIESEL
DESCRIPTION
The electronically controlled viscous fan drive (Fig.
34) and (Fig. 33)is attached to the fan drive pulley
mounted to the engine. The coupling allows the fan
to be driven in a normal manner. The fan speed is
controlled by the electronic control module.
OPERATION
The Engine Control Module (ECM) controls the
level of engagement of the electronically controlled
viscous fan clutch by monitoring coolant tempera-
ture, intake manifold temperature, and air condition-
ing status. Based on cooling requirements, the ECMsends a signal to the viscous fan clutch to increase or
decrease the fan speed.
Fan speed is monitored by the ECM. Fan speeds
above or below a calibrated threshold will set a DTC.
Circuit concerns will also set fan clutch DTC's.
DIAGNOSIS AND TESTING - ELECTRONICALLY
CONTROLLED VISCOUS FAN DRIVE
NOISE
NOTE: It is normal for fan noise to be louder (roar-
ing) when:
²Fan duty cycle high. This may occur when ambi-
ent (outside air temperature) is very high.
²Engine loads and temperatures are high such as
when towing a trailer.
²Aggressive engine braking down a steep grade
where transmission temperatures may be high
²Cool silicone fluid within the fan drive unit is
being redistributed back to its normal disengaged
(warm) position. This can occur during the first 15
seconds to one minute after engine start-up on a cold
engine.
Fig. 33 Electronically Controlled Viscous Drive
1 - ELECTRONICALLY CONTROLLED VISCOUS FAN DRIVE
2 - MOUNTING NUT
3 - WIRING SUPPORT BRACKET
4 - ELECTRICAL CONNECTOR
Fig. 34 Fan Blade/Viscous Fan Drive - 5.9L Diesel
Engine
1 - ELECTRICAL CONNECTOR
2 - VISCOUS FAN DRIVE
3 - FAN BLADE
4 - BOLT (6)
5 - RADIATOR FAN PULLEY
7 - 52 ENGINEDR
FAN DRIVE VISCOUS CLUTCH-GAS ENGINES (Continued)

²Actuator Test- Each time the cluster is put
through the actuator test, the engine coolant temper-
ature gauge needle will be swept to several calibra-
tion points on the gauge scale in a prescribed
sequence in order to confirm the functionality of the
gauge and the cluster control circuitry.
On vehicles with a gasoline engine, the PCM con-
tinually monitors the engine coolant temperature
sensor to determine the engine operating tempera-
ture. On vehicles with a diesel engine, the ECM con-
tinually monitors the engine coolant temperature
sensor to determine the engine operating tempera-
ture. The PCM or ECM then sends the proper engine
coolant temperature messages to the instrument
cluster. For further diagnosis of the engine coolant
temperature gauge or the instrument cluster cir-
cuitry that controls the gauge, (Refer to 8 - ELEC-
TRICAL/INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING). If the instrument cluster turns on
the check gauges indicator due to a high engine tem-
perature gauge reading, it may indicate that the
engine or the engine cooling system requires service.
For proper diagnosis of the engine coolant tempera-
ture sensor, the PCM, the ECM, the PCI data bus, or
the electronic message inputs to the instrument clus-
ter that control the engine coolant temperature
gauge, a DRBIIItscan tool is required. Refer to the
appropriate diagnostic information.
ETC INDICATOR
DESCRIPTION
An Electronic Throttle Control (ETC) indicator is
standard equipment on all gasoline engine instru-
ment clusters (Fig. 16). However, on vehicles not
equipped with the optional 5.7 liter gasoline engine,
this indicator is electronically disabled. The ETC
indicator is located on the right side of the instru-
ment cluster, to the right of the engine temperature
gauge. The ETC indicator consists of a stencil-like
cutout of the International Control and Display Sym-
bol icon for ªElectronic Throttle Controlº in the
opaque layer of the instrument cluster overlay. The
dark outer layer of the overlay prevents the indicator
from being clearly visible when it is not illuminated.
A red Light Emitting Diode (LED) behind the cutout
in the opaque layer of the overlay causes the icon to
appear in red through the translucent outer layer of
the overlay when the indicator is illuminated from
behind by the LED, which is soldered onto theinstrument cluster electronic circuit board. The ETC
indicator is serviced as a unit with the instrument
cluster.
OPERATION
The Electronic Throttle Control (ETC) indicator
gives an indication to the vehicle operator when the
ETC system is faulty or inoperative. The ETC indi-
cator is controlled by a transistor on the instrument
cluster circuit board based upon cluster programming
and electronic messages received by the cluster from
the Powertrain Control Module (PCM) over the Pro-
grammable Communications Interface (PCI) data
bus. The ETC indicator Light Emitting Diode (LED)
is completely controlled by the instrument cluster
logic circuit, and that logic will only allow this indi-
cator to operate when the instrument cluster receives
a battery current input on the fused ignition switch
output (run-start) circuit. Therefore, the LED will
always be off when the ignition switch is in any posi-
tion except On or Start. The LED only illuminates
when it is provided a path to ground by the instru-
ment cluster transistor. The instrument cluster will
turn on the ETC indicator for the following reasons:
²Bulb Test- Each time the ignition switch is
turned to the On position the ETC indicator is illu-
minated for about six seconds. The entire six second
bulb test is a function of the PCM.
²ETC Lamp-On Message- Each time the clus-
ter receives a lamp-on message from the PCM, the
ETC indicator will be illuminated. The indicator can
be flashed on and off, or illuminated solid, as dic-
tated by the PCM message. The indicator remains
illuminated solid or continues to flash for about
twelve seconds or until the cluster receives a lamp-off
message from the PCM, whichever is longer. If the
indicator is illuminated solid with the engine run-
ning the vehicle will usually remain drivable. If the
indicator is flashing with the engine running the
vehicle may require towing. A flashing indicator
means the ETC system requires immediate service.
²Communication Error- If the cluster receives
no ETC lamp messages for three consecutive seconds,
the ETC indicator is illuminated. The indicator
remains illuminated until the cluster receives a sin-
gle lamp-off message from the PCM.
²Actuator Test- Each time the cluster is put
through the actuator test, the ETC indicator will be
turned on, then off again during the bulb check por-
tion of the test to confirm the functionality of the
LED and the cluster control circuitry. The actuator
test illumination of the ETC indicator is a function of
the PCM.
The PCM continually monitors the ETC system cir-
cuits and sensors to decide whether the system is in
good operating condition. The PCM then sends the
Fig. 16 ETC Indicator
DRINSTRUMENT CLUSTER 8J - 25
ENGINE TEMPERATURE GAUGE (Continued)

TRAILER TOW WIRING
DESCRIPTION
Vehicles equipped with an optional factory-in-
stalled trailer towing package have a rear body wire
harness that includes an integral trailer tow wiring
take out that connects to a heavy duty, sealed, 7-pin
trailer tow connector located in the rear bumper (Fig.
23). This harness includes an adapter harness that
adapts the 7-pin trailer tow connector to a standard,
light-duty, 4-pin trailer tow connector. Refer to the
appropriate wiring information.
TURN LAMP
REMOVAL
REMOVAL - WITH CARGO BOX
(1) Disconnect and isolate the negative battery
cable.
(2) Remove the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING - EXTERIOR/TAIL
LAMP UNIT - REMOVAL).
(3) Remove the lamp back plate from the tail lamp
unit.
(4) Release the turn signal bulb locking tabs and
remove the bulb from the back plate.
REMOVAL - WITHOUT CARGO BOX
(1) Disconnect and isolate the negative battery
cable.(2) Remove the four screws that secure the tail
lamp lens to the tail lamp housing (Fig. 24).
(3) Separate the tail lamp lens from the tail lamp
housing.
(4) Push the turn signal bulb inward and rotate it
counter-clockwise.
(5) Remove the turn signal bulb from the tail lamp
socket.
INSTALLATION
INSTALLATION - WITH CARGO BOX
(1) Install the turn signal bulb into the lamp back
plate.
(2) Install the lamp back plate onto the tail lamp
unit.
(3) Install the tail lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING - EXTERIOR/TAIL
LAMP UNIT - INSTALLATION).
(4) Reconnect the negative battery cable.
INSTALLATION - WITHOUT CARGO BOX
(1) Install the turn signal bulb into the tail lamp
socket by pushing inward and rotating it clockwise.
NOTE: Install the tail lamp lens with the clear por-
tion (back-up lens) at the top of the housing. Make
sure that the gasket is correctly in place and not
twisted or torn.
(2) Position the tail lamp lens and gasket onto the
tail lamp unit.
NOTE: Do not overtighten the tail lamp lens screws
or damage to the tail lamp lens may result.
(3) Install the four screws that secure the tail
lamp lens to the tail lamp unit. Tighten the screws
securely.
(4) Reconnect the negative battery cable.
Fig. 23 Trailer Tow Wiring
1 - RETAINER CLIP (4)
2 - REAR BODY HARNESS (TRAILER TOW TAKE OUT)
3 - RETAINER CLIP (2)
4 - WIRE HARNESS CONNECTOR
Fig. 24 Tail Lamp Lens
8L - 24 LAMPS/LIGHTING - EXTERIORDR

TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-23
TOOLS - RE TRANSMISSION, SPECIAL . . 21-191
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-359
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-35
TOOLS - STEERING, SPECIAL............19-5
TOOLS - TRANSFER CASE NV271/NV273,
SPECIAL....................21-474,21-569
TOOLS - WHEEL ALIGNMENT, SPECIAL.....2-7
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, FRONT AXLE - 9 1/4 AA -
SPECIAL............................3-64
TOOLS, FRONT AXLE - C205F - SPECIAL . . . 3-40
TOOLS, HALF SHAFT - SPECIAL..........3-21
TOOLS, MANUAL TRANSMISSION -
NV3500 - SPECIAL...................21-40
TOOLS, MANUAL TRANSMISSION -
NV4500 - SPECIAL...................21-81
TOOLS, MANUAL TRANSMISSION -
NV5600 - SPECIAL..................21-123
TOOLS, PROPELLER SHAFT - SPECIAL.....3-6
TOOLS, REAR AXLE - 10 1/2 AA -
SPECIAL...........................3-120
TOOLS, REAR AXLE - 11 1/2 AA -
SPECIAL...........................3-148
TOOLS, REAR AXLE - 9 1/4 - SPECIAL.....3-90
TOP COVER - INSTALLATION,
INSTRUMENT PANEL..................23-59
TOP COVER - REMOVAL, INSTRUMENT
PANEL.............................23-58
TORSION BAR - DESCRIPTION...........2-26
TORSION BAR - INSTALLATION..........2-27
TORSION BAR - OPERATION.............2-26
TORSION BAR - REMOVAL..............2-26
TORSION BAR CROSS MEMBER
BUSHING - INSTALLATION..............2-15
TORSION BAR CROSSMEMBER
BUSHING - REMOVAL..................2-13
TOUCH-UP - DESCRIPTION, PAINT.......23-74
TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-74
TOW HOOK ASSEMBLY - INSTALLATION,
FRONT.............................13-23
TOW HOOK ASSEMBLY - REMOVAL,
FRONT.............................13-23
TOW WIRING - DESCRIPTION, TRAILER . . 8L-24
TOW/HAUL INDICATOR - DESCRIPTION . . . 8J-39
TOW/HAUL INDICATOR - OPERATION.....8J-39
TOW/HAUL OVERDRIVE SWITCH -
DESCRIPTION................21-261,21-392
TOW/HAUL OVERDRIVE SWITCH -
INSTALLATION................21-262,21-393
TOW/HAUL OVERDRIVE SWITCH -
OPERATION..................21-262,21-392
TOW/HAUL OVERDRIVE SWITCH -
REMOVAL...................21-262,21-392
TOWING - STANDARD PROCEDURE.......0-21
TRACK - DESCRIPTION, POWER SEAT....8N-16
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-17
TRACK - INSTALLATION, POWER SEAT . . . 8N-17
TRACK - INSTALLATION, SEAT..........23-83
TRACK - OPERATION, POWER SEAT.....8N-16
TRACK - REMOVAL, POWER SEAT.......8N-17
TRACK - REMOVAL, SEAT..............23-83
TRACK BAR - INSTALLATION...........19-38
TRACK BAR - REMOVAL...............19-38
TRAC-RITE - ASSEMBLY, DIFFERENTIAL . . 3-133,
3-161
TRAC-RITE - CLEANING, DIFFERENTIAL . . 3-132,
3-160
TRAC-RITE - DESCRIPTION,
DIFFERENTIAL..................3-131,3-158
TRAC-RITE - DISASSEMBLY,
DIFFERENTIAL..................3-131,3-158
TRAC-RITE - INSPECTION, DIFFERENTIAL . 3-132,
3-160
TRAC-RITE - OPERATION, DIFFERENTIAL . 3-131,
3-158
TRAILER HITCH - INSTALLATION
........13-25
TRAILER HITCH - REMOVAL
............13-25
TRAILER TOW WIRING - DESCRIPTION
. . . 8L-24
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION
........................7-68
TRANS COOLER - 5.9L DIESEL -
OPERATION
..........................7-69TRANS COOLER - DESCRIPTION.........7-67
TRANS COOLER - INSTALLATION.........7-68
TRANS COOLER - OPERATION...........7-67
TRANS COOLER - REMOVAL.............7-68
TRANS TEMP INDICATOR -
DESCRIPTION.......................8J-40
TRANS TEMP INDICATOR - OPERATION . . . 8J-40
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-15
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-16
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-16
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-16
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-16
TRANSFER CASE - DESCRIPTION..........0-4
TRANSFER CASE - NV241 GENII -
ASSEMBLY.........................21-428
TRANSFER CASE - NV241 GENII -
CLEANING.........................21-426
TRANSFER CASE - NV241 GENII -
DESCRIPTION......................21-415
TRANSFER CASE - NV241 GENII -
DIAGNOSIS AND TESTING............21-416
TRANSFER CASE - NV241 GENII -
DISASSEMBLY......................21-417
TRANSFER CASE - NV241 GENII -
INSPECTION.......................21-426
TRANSFER CASE - NV241 GENII -
INSTALLATION.......................21-438
TRANSFER CASE - NV241 GENII -
OPERATION........................21-415
TRANSFER CASE - NV241 GENII -
REMOVAL.........................21-417
TRANSFER CASE - NV243 - ASSEMBLY . . 21-496
TRANSFER CASE - NV243 - CLEANING . . 21-493
TRANSFER CASE - NV243 -
DESCRIPTION......................21-482
TRANSFER CASE - NV243 - DIAGNOSIS
AND TESTING......................21-483
TRANSFER CASE - NV243 -
DISASSEMBLY......................21-484
TRANSFER CASE - NV243 - INSPECTION . 21-493
TRANSFER CASE - NV243 -
INSTALLATION......................21-505
TRANSFER CASE - NV243 - OPERATION . 21-483
TRANSFER CASE - NV243 - REMOVAL . . . 21-484
TRANSFER CASE - NV244 - DIAGNOSIS
AND TESTING......................21-513
TRANSFER CASE - NV244 GENII -
ASSEMBLY.........................21-525
TRANSFER CASE - NV244 GENII -
CLEANING.........................21-523
TRANSFER CASE - NV244 GENII -
DESCRIPTION......................21-512
TRANSFER CASE - NV244 GENII -
DISASSEMBLY......................21-514
TRANSFER CASE - NV244 GENII -
INSPECTION.......................21-523
TRANSFER CASE - NV244 GENII -
INSTALLATION......................21-534
TRANSFER CASE - NV244 GENII -
OPERATION........................21-513
TRANSFER CASE - NV244 GENII -
REMOVAL.........................21-514
TRANSFER CASE - NV271 - ASSEMBLY . . 21-461
TRANSFER CASE - NV271 - CLEANING . . 21-459
TRANSFER CASE - NV271 -
DESCRIPTION......................21-447
TRANSFER CASE - NV271 - DIAGNOSIS
AND TESTING......................21-448
TRANSFER CASE - NV271 -
DISASSEMBLY......................21-450
TRANSFER CASE - NV271 - INSPECTION . 21-459
TRANSFER CASE - NV271 -
INSTALLATION......................21-473
TRANSFER CASE - NV271 - OPERATION . 21-448
TRANSFER CASE - NV271 - REMOVAL . . . 21-450
TRANSFER CASE - NV273 - ASSEMBLY
. . 21-556
TRANSFER CASE - NV273 - CLEANING
. . 21-554
TRANSFER CASE - NV273 -
DESCRIPTION
......................21-542
TRANSFER CASE - NV273 - DIAGNOSIS
AND TESTING
......................21-543
TRANSFER CASE - NV273 -
DISASSEMBLY
......................21-544TRANSFER CASE - NV273 - INSPECTION . 21-554
TRANSFER CASE - NV273 -
INSTALLATION......................21-568
TRANSFER CASE - NV273 - OPERATION . 21-543
TRANSFER CASE - NV273 - REMOVAL . . . 21-544
TRANSFER CASE CONTROL MODULE -
DESCRIPTION.......................8E-16
TRANSFER CASE CONTROL MODULE -
OPERATION.........................8E-16
TRANSFER CASE, NV241 GENII........21-438
TRANSFER CASE, NV241/NV243........21-439
TRANSFER CASE, NV243.......21-505,21-506
TRANSFER CASE, NV244 GENII........21-535
TRANSFER CASE, NV271.............21-473
TRANSFER CASE NV271/NV273, SPECIAL
TOOLS......................21-474,21-569
TRANSFER CASE, NV273.............21-568
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-26
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-26
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-64
TRANSFER PUMP - INSTALLATION, FUEL . 14-65
TRANSFER PUMP - OPERATION, FUEL....14-64
TRANSFER PUMP - REMOVAL, FUEL.....14-64
TRANSMISSION - 45RFE/545RFE -
DESCRIPTION, AUTOMATIC............21-312
TRANSMISSION - 45RFE/545RFE -
OPERATION, AUTOMATIC.............21-313
TRANSMISSION - 48RE - DESCRIPTION,
AUTOMATIC........................21-132
TRANSMISSION - 48RE - OPERATION,
AUTOMATIC........................21-134
TRANSMISSION - CLEANING..........21-106
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-4
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC..........21-140,21-314
TRANSMISSION - NV3500 - ASSEMBLY,
MANUAL...........................21-17
TRANSMISSION - NV3500 - CLEANING,
MANUAL...........................21-15
TRANSMISSION - NV3500 -
DESCRIPTION, MANUAL................21-1
TRANSMISSION - NV3500 - DIAGNOSIS
AND TESTING, MANUAL................21-3
TRANSMISSION - NV3500 -
DISASSEMBLY, MANUAL................21-4
TRANSMISSION - NV3500 -
INSPECTION, MANUAL................21-16
TRANSMISSION - NV3500 -
INSTALLATION, MANUAL..............21-39
TRANSMISSION - NV3500 - OPERATION,
MANUAL............................21-1
TRANSMISSION - NV3500 - REMOVAL,
MANUAL............................21-3
TRANSMISSION - NV3500 - SPECIAL
TOOLS, MANUAL.....................21-40
TRANSMISSION - NV3500 -
SPECIFICATIONS, MANUAL.............21-40
TRANSMISSION - NV4500 - ASSEMBLY,
MANUAL...........................21-63
TRANSMISSION - NV4500 - CLEANING,
MANUAL...........................21-62
TRANSMISSION - NV4500 -
DESCRIPTION, MANUAL...............21-43
TRANSMISSION - NV4500 - DIAGNOSIS
AND TESTING, MANUAL...............21-44
TRANSMISSION - NV4500 -
DISASSEMBLY, MANUAL...............21-46
TRANSMISSION - NV4500 -
INSPECTION, MANUAL................21-62
TRANSMISSION - NV4500 -
INSTALLATION, MANUAL..............21-80
TRANSMISSION - NV4500 - OPERATION,
MANUAL...........................21-43
TRANSMISSION - NV4500 - REMOVAL,
MANUAL...........................21-44
TRANSMISSION - NV4500 - SPECIAL
TOOLS, MANUAL
.....................21-81
TRANSMISSION - NV4500 -
SPECIFICATIONS, MANUAL
.............21-81
TRANSMISSION - NV5600 - ASSEMBLY,
MANUAL
..........................21-106
TRANSMISSION - NV5600 -
DESCRIPTION, MANUAL
...............21-88
TRANSMISSION - NV5600 - DIAGNOSIS
AND TESTING, MANUAL
...............21-90
34 INDEXDR
Description Group-Page Description Group-Page Description Group-Page