transmission DODGE RAM 1999 Service Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 390 of 1691
scan tool displayed P/N and D/R in correct positions, go to next step.
4) Raise drive wheels and support vehicle, allowing wheels to
spin. Using scan tool, erase DTCs. Start engine. Using scan tool, read
Output Speed Sensor (OSS). Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
If scan tool displays OSS more than 60 RPM, go to next step. If scan
tool displays OSS 60 RPM or less, go to step 7).
5) While wheels are spinning, wiggle wiring between OSS and
PCM. If OSS reading dropped while wiggling, repair intermittent short
or open circuit. Perform TEST VER-5A under VERIFICATION TESTS. If OSS
reading did not drop, go to next step.
6) Using scan tool, erase DTCs. Road test vehicle. Read DTCs.
If FTC P0720 returns, replace PCM. Perform TEST VER-5A under
VERIFICATION TESTS. If FTC P0720 did not return, go to step 13).
7) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance
between ground and OSS signal circuit at PCM connector C2, terminal
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-5A under VERIFICATION TESTS.
8) Using an ohmmeter, measure resistance between ground and
OSS ground circuit at PCM connector C2, terminal No. 25 (Dark
Blue/Black wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-5A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
9) Disconnect OSS. Using an ohmmeter, measure resistance
across OSS terminals. If resistance is not 300-1200 ohms, replace OSS.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 300-
1200 ohms, go to next step.
10) Using an ohmmeter, measure resistance of OSS signal
circuit between PCM connector C2, terminal No. 28 and OSS connector
(Light Green/Black wire on Ram Pickup; Light Green/White wire on all
other models). If resistance is more than 5 ohms, repair open circuit.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is 5 ohms
or less, go to next step.
11) Using an ohmmeter, measure resistance of OSS ground
circuit between PCM connector C2, terminal No. 25 and OSS connector
(Dark Blue/Black wire). If resistance is more than 5 ohms, repair open\
circuit. Perform TEST VER-5A under VERIFICATION TESTS. If resistance
is 5 ohms or less, go to next step.
12) Reconnect OSS. Using an ohmmeter, measure resistance
between PCM connector C2, terminals No. 25 (Dark Blue/Black wire) and
No. 28 (Light Green/Black wire on Ram Pickup; Light Green/White wire
on all other models). If resistance is 300-1200 ohms, replace PCM.
Perform TEST VER-5A under VERIFICATION TESTS. If resistance is not
300-1200 ohms, go to next step.
13) Inspect wiring and connectors. repair as necessary.
Perform TEST VER-5A under VERIFICATION TESTS. If wiring and connectors
are okay, go to next step.
14) Conditions required to set FTC are not present at this
time. Check freeze frame data to determine conditions when FTC was
set. Raise drive wheels and support vehicle, allowing wheels to spin.
Using scan tool, read OSS. Shift transmission into first gear. While
observing scan tool, allow wheels to spin at a speed less than 15 MPH.
Wiggle wiring between OSS and PCM. If OSS reading dropped while
wiggling, repair intermittent short or open circuit. Perform TEST VER-
5A under VERIFICATION TESTS. If OSS reading did not drop, no problem
is indicated at this time.
FTC P1595: SPEED CONTROL SOLENOID CIRCUITS
Speed Control (S/C) solenoid circuits are monitored when
engine is running, S/C switch is on and battery voltage is more than
Page 398 of 1691
1) Turn ignition off. Disconnect brake switch connector.
Inspect connector. Clean or repair as necessary. Turn ignition on.
Using a voltmeter, measure voltage of brake switch sense circuit at
brake switch White/Pink wire. If voltage is more than 10 volts, go to
next step. If voltage is 10 volts or less, go to step 3).
2) Connect a jumper wire between ground and brake switch
connector White/Pink wire. Using scan tool, read brake switch input
status. If scan tool displays brake switch released, replace brake
switch. Perform TEST VER-4A under VERIFICATION TESTS. If scan tool
does not display brake switch released, repair open ground circuit.
Perform TEST VER-4A under VERIFICATION TESTS.
3) Disconnect PCM connectors. Inspect connectors. Clean or
repair as necessary. Using an ohmmeter, measure resistance between
ground and brake switch sense circuit at PCM connector C3, terminal
No. 24 (White/Pink wire). If resistance less than 5 ohms, repair short\
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
4) Using an ohmmeter, measure resistance of brake switch
sense circuit between PCM connector C3, terminal No. 24 and brake
switch White/Pink wire. If resistance is 5 ohms or more, repair open
brake switch sense circuit. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is less than 5 ohms, replace PCM. Perform TEST
VER-4A under VERIFICATION TESTS.
NTC-2: CHECKING FOR SPEED CONTROL DENIED MESSAGE
At this time speed control switch and servo functions appear
to operate properly. Using scan tool, monitor speed control output
status. Road test vehicle at speeds more than 30 MPH. Attempt to set
speed control. See SCAN TOOL DENIED STATUS table. Items listed in
table will not allow speed control to set. The last or most recent
cause for speed control not to set is indicated by denied status.
Correct fault and recheck system operation.
SCAN TOOL DENIED STATUS
\
\
\
\
\
\
\
Denied Message Reason
\
\b \
\
\
\
\
\
ON/OFF PCM Does Not See An ON Signal From Switch
At PCM Terminal No. 41
\
\b \
\
\
\
\
\
SPEED Vehicle Speed As Seen By PCM Terminal
No. 66 Is Not Greater Than 36 MPH
\
\b \
\
\
\
\
\
RPM Engine RPM Is Excessively High
\
\b \
\
\
\
\
\
BRAKE Brake Switch Sense Circuit Is Open
Indicating That Brakes Are Applied
\
\b \
\
\
\
\
\
P/N Park/Neutral Switch Sense Circuit Is Grounded
Indicating That Transmission Is In Park Or Neutral
\
\b \
\
\
\
\
\
RPM/SPD PCM Senses Excessive Engine RPM
For A Given Vehicle Speed
\
\b \
\
\
\
\
\
SOL FLT PCM Senses A Servo Solenoid Circuit
Trouble Code That Is Maturing Or Set In Memory
\
\
\
\
\
\
\
\f
NTC-3: SPEED CONTROL ON/OFF SWITCH
Possible Causes:
Page 408 of 1691
FLUID TYPE
Use SAE 80W-90 or 90W hypoid gear lubricant with MIL-L-2105-C
and API GL-5 ratings.
TROUBLE SHOOTING
NOTE: See appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
REMOVAL & INSTALLATION
AXLE SHAFT & HUB BEARING
Removal
1) Raise and support vehicle. Remove wheel. Remove brake
caliper with hose attached, and secure aside. DO NOT allow brake
caliper to hang by brake hose. Remove brake rotor. Remove ABS wheel
speed sensor (if equipped). Remove grease cap from center of front
hub. Remove cotter pin from end of axle shaft. Remove axle nut and
washer.
2) Remove hub/bearing assembly-to-knuckle bolts. Remove
hub/bearing assembly from steering knuckle and axle shaft. Remove
brake dust shield. To remove right (passenger-side) axle shaft,
carefully pull axle shaft from axle housing.
NOTE: Left axle shaft will disengage from collar located on
intermediate axle shaft.
3) To remove left (driver's side) axle shaft, disconnect
electrical connector and vacuum hoses at vacuum shift motor. Remove
bolts, vacuum shift motor and gasket. Carefully pull axle shaft from
axle housing and collar on intermediate axle shaft.
Installation
1) Install NEW oil seal on axle shaft with seal lip facing
toward splines on differential end of axle shaft. Coat seal lip with
wheel bearing grease.
2) Install right axle shaft into axle housing. Ensure axle
shaft engages with side gears in differential.
3) To install left axle shaft, ensure collar is engaged with
splines on intermediate axle shaft. Install left axle shaft into axle
housing. Ensure axle shaft engages with splines on collar. Install
vacuum shift motor, ensuring fork on vacuum shift motor engages groove
on collar. Install and tighten bolts to specification. See TORQUE
SPECIFICATIONS table.
4) To complete installation, reverse removal procedure. Apply
silicone rubber sealant to edge of grease cap before installing.
Tighten bolts/nuts to specification. See TORQUE SPECIFICATIONS table.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer selector levers case are in Neutral. Reference mark drive
shaft and pinion flange for reassembly reference.
2) Remove bolts and "U" joint straps at pinion flange. Remove
center carrier bearing bolts (if equipped). Remove drive shaft.
CAUTION: The "U" joint components are not serviceable. Replace
complete assembly. DO NOT reuse.
Page 421 of 1691
(1) - Approximate drive axle capacity listed. Lubricant level should
be within 1/2" below bottom of oil filler hole in axle housing
cover.
( 2) - Add container of Mopar Gear Oil Friction Modifier when
refilling.
\
\
\
\
\
\
\
FLUID TYPE
Use SAE 80W-90 or SAE 90W hypoid gear lubricant with MIL-L-
2105-B and API GL-5 ratings. Also add a container of Mopar Gear Oil
Friction Modifier when refilling.
FLUID DRAIN & REFILL
1) With lubricant of rear axle assembly at normal operating
temperature, raise and support vehicle so rear wheels are free to
rotate. Clean around axle housing cover. Loosen axle housing cover
bolts. Drain lubricant from axle housing. Remove bolts and axle
housing cover.
2) Position differential so hole in differential case faces
down. Wipe all accessible areas of axle housing. Ensure sealing
surfaces on axle housing and cover are clean. Apply a 1/4" thick bead
of silicone sealant on inside of bolt holes and along sealing surfaces
on axle housing cover.
3) Install axle housing cover, axle identification tag and
retaining bolts. Tighten bolts to 30 ft. lbs. (41 N.m). Remove oil
filler plug. Add a container of Mopar Gear Oil Friction Modifier. Fill
axle with gear lube. Install oil filler plug. Lower vehicle.
TROUBLE SHOOTING
DIFFERENTIAL NOISE
1) Ensure differential lubricant is at normal operating
temperature. Road test vehicle. Note if differential noise exists in
turns, but not during straight-ahead driving. Probable cause is
incorrect or insufficient rear axle lubricant or additive.
2) Drain and refill rear axle. See FLUID DRAIN & REFILL under
LUBRICATION. Road test vehicle and note if noise still exists, it may
be necessary to disassemble rear axle so differential can be repaired.
See RBI FULL-FLOATING AXLES article for removal of differential case.
TESTING
NOTE: Power-Lok differential can be tested without removing
differential carrier from axle housing. Either test can be
used to check drive axle.
TEST I
1) Place blocks under both front wheels. Ensure engine is off
and transmission is in Neutral. Release parking brake. Raise one rear
wheel until it is completely clear of the floor. Remove wheel. Install
Adapter (6790) to wheel studs, and tighten securely.
2) Using torque wrench on adapter, rotate axle, and record
torque required. Repeat procedure for remaining rear wheel position.
If rotational torque for either rear wheel is less than 30 ft. lbs.
(41 N.m) or greater than 200 ft. lbs. (271 N.m), Power-Lok unit must\
be replaced or repaired.
Page 425 of 1691
![DODGE RAM 1999 Service Owners Manual 267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD ....................................](/img/12/56915/w960_56915-424.png "DODGE RAM 1999 Service Owners Manual 267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD ....................................")
267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD .................................................. 10.1 (4.8)\
Ram Van/Wagon
248 RBI ................................................ 6.0 (2.8)\
(1) - Approximate drive axle capacity listed. Lubricant level should
be 1/2" below oil filler hole in axle housing cover.
\
\
\
\
\
\
\
FLUID TYPE
Use SAE 80W-90 for 286 models, or 90W for all other models,
hypoid gear lubricant with MIL-L-2105-C and API GL-5 ratings. Models
with Trac-Lok require addition of 6 ozs. (.18 L) Mopar(R) friction
modifier (limited slip additive). Ram Pickups equipped with Power-Lok
require addition of 8 ozs. (.24 L) Mopar(R) friction modifier.
TROUBLE SHOOTING
NOTE: See appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
REMOVAL & INSTALLATION
REAR HUB, BEARINGS & AXLE SHAFT
Removal
Raise and support vehicle. Remove wheel. Remove bolts, axle
shaft and gasket. Remove nut lock from adjusting nut. See Fig. 1.
Remove adjusting nut and outer wheel bearing. Remove rear hub and
brake drum. Remove oil seal and inner wheel bearing (if necessary).
Installation
1) Pack wheel bearings with wheel bearing grease. Install
inner wheel bearing and oil seal in rear hub (if removed). Install
rear hub and brake drum. Install outer wheel bearing and adjusting
nut. Tighten adjusting nut to specification while rotating rear hub
and brake drum. See TORQUE SPECIFICATIONS table.
2) Back off adjusting nut approximately 1/8 turn to obtain .
001-.010" (.03-.25 mm) wheel bearing end play. Tap key lock into
adjusting nut and keyway on axle housing.
3) To install remaining components, reverse removal
procedure. Use NEW gasket when installing axle shaft. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer case selector levers are in Neutral. Remove wheel assembly.
Remove RWAL sensor, if equipped. Reference mark drive shaft to pinion
flange for reassembly.
2) On 2-piece drive shafts, scribe center carrier bearing-to-
frame bracket reference line for reassembly. On all drive shafts,
remove bolts and "U" joint straps at pinion flange. Remove center
carrier bearing bolts, if equipped. Remove spring clamps and brackets.
Remove drive shaft(s).
CAUTION: The "U" joint straps and bolts must be replaced. DO NOT
Page 440 of 1691
axle housing.
CAUTION: DO NOT damage axle shaft bearing in axle housing when
removing axle shaft.
3) Inspect axle shaft-to-axle shaft bearing contact area for
damage. Replace axle shaft and axle shaft bearing if axle shaft is
damaged. Using small pry bar, pry oil seal from axle housing (if
necessary).
4) If replacing axle shaft bearing, use appropriate bearing
puller and slide hammer to remove axle shaft bearing. Rotate threaded
shaft on bearing puller to remove axle shaft bearing.
CAUTION: Ensure axle shaft bearing surface in axle housing is free of
burrs and clean before installing axle shaft bearing.
Installation
1) Using appropriate bearing/seal installer, install bearing.
Ensure axle shaft bearing is bottomed against shoulder in bore.
Install NEW oil seal in axle housing until installer contacts axle
housing.
2) Lubricate axle shaft bearing and oil seal lip with gear
lube. Install axle shaft so splines engage with splines on side gear.
DO NOT damage oil sea when installing axle shaft.
3) Install clip on end of axle shaft. Pull axle shaft
outward, ensuring clip fully seats in counterbore on side gear.
Install pinion shaft ensuring pinion shaft hole aligns with lock bolt
hole.
4) Apply Loctite to CLEAN threads on lock bolt. Install and
tighten lock bolt to specification. See TORQUE SPECIFICATIONS. Ensure
axle housing and axle housing cover sealing surfaces are clean.
5) Apply a 1/4" thick bead of silicone sealant on inside of
bolt holes and along sealing surfaces on axle housing cover. Install
axle housing cover, axle identification tag, and retaining bolts.
Tighten bolts in crisscross pattern to proper specification. See
TORQUE SPECIFICATIONS.
6) To install remaining components, reverse removal
procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
Fill differential. See LUBRICATION.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer case are in Neutral. Scribe mark on drive shaft-to-pinion
flange for reassembly reference.
2) On 2-piece drive shafts, scribe center carrier bearing-to-
frame bracket reference line for reassembly reference. On all drive
shafts, remove bolts and "U" joint straps at pinion flange. Remove
center carrier bearing bolts (if equipped). Remove drive shaft(s).
CAUTION: "U" joint straps and bolts must be replaced. DO NOT reuse.
Installation
To install, reverse removal procedure using NEW "U" joint
straps and bolts. Ensure all reference marks are aligned. Tighten
bolts to specification. See TORQUE SPECIFICATIONS.
PINION FLANGE & OIL SEAL
CAUTION: Following procedure must be used to retain proper pinion
bearing preload. Failure to follow procedure may result in
premature axle assembly or component failure. Ensure pinion
Page 453 of 1691
TESTING
NOTE: Trac-Lok differential can be tested without removing
differential case from axle housing.
1) Place blocks under both front wheels. Ensure engine is off
and transmission is in Neutral. Release parking brake. Raise one rear
wheel until it is completely clear of the floor. Remove wheel. Install
Adapter (6790) to wheel studs and tighten securely.
2) Using torque wrench on adapter, rotate axle and record
torque required. Repeat procedure for remaining rear wheel position.
If rotational torque for either rear wheel is less than 30 ft. lbs.
(40.1 N.m) or greater than 200 ft. lbs. (271 N.m), Trac-Lok unit mus\
t
be replaced or repaired.
REMOVAL & INSTALLATION
Servicing procedure is same as that used for standard
differential. See RBI FULL FLOATING AXLES article for servicing
procedures.
OVERHAUL
DIFFERENTIAL CARRIER
Disassembly
1) Place appropriate side gear holding tool in soft-jaw vise.
Position differential carrier on holding tool. Remove ring gear, if
necessary. Ring gear removal is only necessary when ring gear is being
replaced.
2) Remove roll pin holding pinion mate shaft into housing.
Remove pinion gear mate shaft. A drift and hammer can be used if
necessary. See Fig. 1.
3) Install appropriate Step Plate on lower side gear. Install
appropriate threaded forcing screw into upper side gear. See Fig. 2.
4) Thread Forcing Screw into threaded adapter disc until
forcing screw is centered in threaded adapter disc. Perform STEP 1
shown in illustration. See Fig. 2.
5) Place small screwdriver in slot of threaded adapter disc
to prevent disc from rotating. Tighten forcing screw to relieve
tension from clutch pack.
6) Remove pinion gear thrust washers. Loosen forcing screw to
release pressure from clutch pack. Install appropriate turning bar in
hole on side of differential case. Perform STEP 2 shown in
illustration. See Fig. 2.
7) Using turning bar, rotate differential case until pinion
gears can be removed. Remove pinion gears. Remove turning bar, forcing
screw, step plate, and threaded adapter disc from differential case.
8) Remove upper side gear and clutch pack. See Fig. 1. Remove
differential case from axle shaft. Remove remaining side gear and
clutch pack from differential case.
CAUTION: Mark clutch pack location for reassembly reference. Note
position of clutch pack components before removing clutch
pack retainers. Clutch packs must be assembled in correct
order and installed in original location.
9) Remove clutch pack retainers from clutch pack. Keeping
clutch pack components in correct order, disassemble clutch pack.
Page 457 of 1691
DRIV E S H AFTS & " U " J O IN TS - R W D
1999 D odge P ic ku p R 1500
1998-99 Drive Axles
CHRY - Drive Shafts & "U" Joints - RWD Trucks
Dakota, Ram Pickup, Ram Van/Wagon
DESCRIPTION
Drive shafts are balanced, tubular shafts with "U" joints
attached at each end. Flanges or yokes are used to connect drive shaft
"U" joints to rear differential pinion flange or to transmission
output shaft. "U" joint bearing caps are bolted to shaft flanges, or
are pressed into shaft yokes. Drive shafts can be steel or aluminum.
Number of drive shafts used by vehicle depends on vehicle
length and 4WD capability. Long wheel base vehicles use 2 rear drive
shafts with a center bearing support assembly. See Fig. 1. 4WD
applications use a double cardan constant velocity joint on front axle
drive shaft for correct drive shaft-to-front axle alignment. See
Fig. 12 .
Locations of slip joints and splined shafts vary with model
application. Single tube type drive shaft has slip joint on outside of
"U" joint flange/yoke. This slip joint slides in and out on
transmission's splined main shaft.
Fig. 1: Identifying Common Drive Shaft Combinations
Courtesy of Chrysler Corp.
LUBRICATION
Page 458 of 1691
Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.
Page 459 of 1691
Fig. 2: Checking Phase Alignment Of One-Piece Drive Shaft
2-Piece Shafts
1) On most models with 2-piece drive shafts, proper yoke
phasing is accomplished by keys on drive shaft spline and keyway in
slip joint splines. Drive shafts of this type will fit together only
one way. Non-key drive shafts will fit together in any order on
spline.
2) Rotate transmission flange/yoke until flange/yoke ears
(trunnion axis) are in horizontal plane. Install front drive shaft-to-\
transmission flange/yoke keeping flange/yoke in horizontal plane. This
puts both flange/yoke ears of front drive shaft in vertical plane. See
Fig. 3 .
3) Connect center bearing support assembly to crossmember
bracket. Ensure front face of center bearing support assembly is
perpendicular (90
) to center line of drive shaft. If center bearing
support assembly is installed crooked or off center, drive shaft
vibration and/or noise will result. See Fig. 8.
4) Align and install rear drive shaft splines into slip yoke
splines while keeping rear drive shaft flange/yoke in horizontal
plane. Drive shaft rear "U" joint mounting caps will be in vertical
plane. Set differential pinion flange in vertical plane. Connect rear
drive shaft-to-pinion flange. If 2-piece shaft is correctly installed,
center line of flange/yokes trunnion axis for each individual shaft
will be parallel. See Fig. 3.
Fig. 3: Checking Phase Alignment Of 2-Piece Drive Shaft
Courtesy of Chrysler Corp.
CHECKING RUNOUT