battery DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 648 of 1691
Fig. 13: Drive Belt Routing (5.9L - Heavy Duty Cycle)
Courtesy of Chrysler Corp.
OIL PAN
Removal (Dakota 2WD & Durango 2WD)
1) Disconnect negative battery cable. Remove oil dipstick and
distributor cap. Raise and support vehicle. Drain engine oil.
2) Remove exhaust pipe. Remove side engine mount bolts.
Slightly raise engine. When engine is at adequate height, install
bolts in side engine mount-to-frame bracket holes to support engine.
3) Lower engine, and allow it to rest on bolts installed in
side engine mounts. Remove oil pan bolts, oil pan and gaskets.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
where oil pan side gaskets meet end seals, and where end seals contact
cylinder block. See Fig. 14.
2) To facilitate oil pan installation, fabricate 4 alignment
dowels from 1 1/2" x 5/16" bolts. See Fig. 15. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table. To install remaining
Page 649 of 1691
components, reverse removal procedure.
Removal (Dakota 4WD & Durango 4WD)
1) Disconnect negative battery cable. Remove oil dipstick.
Drain engine oil. Remove exhaust pipe crossover and lower transmission
cover.
2) Remove front drive axle for access to oil pan. For front
drive axle removal, loosen wheel lug nuts. Remove cotter pin, lock nut
and spring washer. Loosen axle shaft nut with vehicle on floor and
brakes applied. Raise and support vehicle.
CAUTION: DO NOT pull on rubber boot during axle shaft removal. Pull on
outer CV joint only.
3) Remove wheels and skid plate. Remove axle shaft nut.
Remove axle shaft-to-differential flange bolts at front drive axle.
Support axle shaft, and separate axle splines from wheel hub by
pulling inward at outer CV joint.
4) Remove remaining axle shaft. Mark front drive shaft and
transfer case yoke for installation reference. Remove front drive
shaft from transfer case. Disconnect vacuum hoses from shift motor and
electrical connections at shift indicator switch.
5) Support front drive axle using a floor jack. Remove front
drive axle and shift motor bolts. Lower floor jack, and remove front
drive axle with drive shaft. Remove transmission lower cover. Remove
bolts, oil pan and gasket.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
oil pan side gaskets meet end seals and end seals contact cylinder
block. See Fig. 14.
2) To facilitate oil pan installation, fabricate 4 alignment
dowels from 1 1/2" x 5/16" bolts. See Fig. 15. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
3) To install remaining components, reverse removal
procedure. When installing front drive axle, loosely install all bolts
before tightening to specification. Tighten axle shaft nut to
specification with vehicle on ground. See TORQUE SPECIFICATIONS table.
Ensure reference marks on transfer case yoke and front drive shaft are
aligned.
Removal (Ram Pickup & Ram Van/Wagon - 3.9L)
1) Disconnect negative battery cable. Remove oil dipstick. On
Ram Van/Wagon, remove engine cover. On all models, remove air cleaner
and engine controller. Raise and support vehicle. Drain engine oil.
2) Remove left engine-to-transmission strut. Loosen exhaust
pipe support bracket. Disconnect exhaust pipe. On Ram Pickup, remove
oil pan and gasket.
3) On Ram Van/Wagon, remove starter, transmission dust
shield, oxygen sensor and air injection tube. On all models, remove
right engine mount nut. Loosen, but DO NOT remove, left engine mount
nut.
4) Support right side of engine using jackstand. Remove
transmission mount through-bolt, and support transmission using
jackstand. Raise engine and transmission enough for oil pan removal.
Remove bolts, oil pan and gasket.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
oil pan side gaskets meet end seals and end seals contact cylinder
block. See Fig. 14.
Page 650 of 1691
2) To facilitate oil pan installation, fabricate 4 alignment
dowels from 1 1/2" x 5/16" bolts. See Fig. 15. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table. To install remaining
components, reverse removal procedure. Tighten bolts to specification.
See TORQUE SPECIFICATIONS table. To install remaining components,
reverse removal procedure.
Removal (Ram Pickup & Ram Van/Wagon - 5.2L & 5.9L)
Disconnect negative battery cable. Remove oil dipstick. Raise
and support vehicle. Drain engine oil. Remove exhaust pipe. Remove
left engine-to-transmission strut. Remove bolts, oil pan and gasket.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
oil pan side gaskets meet end seals and end seals contact cylinder
block. See Fig. 14.
2) To facilitate oil pan installation, fabricate 4 alignment
dowels from 1 1/2" x 5/16" bolts. See Fig. 15. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table. To install remaining
components, reverse removal procedure.
Removal (Grand Cherokee)
Disconnect negative battery cable. Remove oil dipstick. Raise
and support vehicle. Drain engine oil. Disconnect O2 sensor. Remove
exhaust pipe and starter. Remove left engine-to-transmission strut.
Disconnect oil level sensor (if equipped). Remove bolts, oil pan and
gasket. DO NOT damage oil level sensor.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
oil pan side gaskets meet end seals and end seals contact cylinder
block. See Fig. 14.
2) To facilitate oil pan installation on all models,
fabricate 4 alignment dowels from 1 1/2" x 5/16" bolts. See Fig. 15.
Tighten bolts to specification. See TORQUE SPECIFICATIONS table. To
install remaining components, reverse removal procedure.
Fig. 14: Applying Sealant On Oil Pan Sealing Surfaces
Courtesy of Chrysler Corp.
Page 704 of 1691
* E N G IN E S YSTE M S U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Engine Performance and Maintenance Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
Engine Assemblies
CYLINDER HEAD ASSEMBLIES
LONG BLOCK ASSEMBLIES
SHORT BLOCK ASSEMBLIES
Engine Components
ACCELERATOR PEDAL POSITION SENSORS
ACCESSORY BELTS
ACCESSORY PULLEYS
ACTUATORS
AIR CONDITIONING CYCLING SWITCHES
AIR CONDITIONING PRESSURE SENSORS
AIR DUCTS AND TUBES
AIR FILTER ELEMENTS
AIR FILTER GASKETS
AIR FILTER HOUSINGS AND GASKETS
AIR FUEL RATIO SENSORS
AIR INJECTION CONTROL SOLENOIDS
AIR PLENUMS
AIR PUMP BELTS
AIR PUMPS (ELECTRIC-DRIVEN)
AIR TUBES
ASPIRATOR, CHECK AND DECEL VALVES
BAFFLES
BALLAST PRIMARY SUPPLY RESISTOR WIRES
BALLAST RESISTORS AND PRIMARY SUPPLY RESISTOR WIRES
BAROMETRIC PRESSURE SENSORS
BATTERIES
BATTERY CABLES, WIRES AND CONNECTORS
BATTERY CONNECTORS
BATTERY TRAYS AND HOLD DOWN HARDWARE
BATTERY WIRES
BELT-DRIVEN AIR PUMPS
BELT IDLER ASSEMBLIES (ACCESSORY AND CAM BELTS)
BELT TENSIONERS (ACCESSORY AND CAM BELTS)
BOOST CONTROL MECHANISMS
CAMSHAFT POSITION SENSORS
CARBURETORS AND CHOKES
CASTING CORE PLUGS AND EXPANSION PLUGS
CHARGE AIR COOLERS "INTERCOOLERS" (CAC)
CHECK VALVES
CHOKES
Page 723 of 1691
replacement of part.
(2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
BATTERIES
Proper operation of any electrical system or component can be
affected by battery condition. The battery(ies) must meet or exceed
minimum specification for vehicle as equipped and test to that
specific battery's CCA.
Definition of Terms
* Battery Performance Testing
Testing that determines whether or not a battery meets both
vehicle OEM and battery manufacturer's specifications.
* Cold Cranking Amp (CCA) Rating
The number of amperes a new, fully charged battery at
0
F (-17.8 C) can deliver for 30 seconds and maintain at
least a voltage of 1.2 volts per cell (7.2 volts for a
12-volt battery).
* Cranking Amps (CA)
The number of amperes a new, fully charged battery, typically
at 32
F (0 C) can deliver for 30 seconds and maintain at
least a voltage of 1.2 volts per cell (7.2 volts for a
12-volt battery).
* OEM Cranking Amps
The minimum CCA required by the original vehicle manufacturer
for a specific vehicle.
BATTERY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Battery frozen .......... .. ......... ( 1) Further inspection
required.
Case leaking ............ A ............ Require replacement.
Casing swollen .......... A .......... ( 2) Further inspection
required.
Circuit open internally . A ............ Require replacement.
Electrolyte
contamination .......... A .......... ( 2) Further inspection
required.
Electrolyte
discoloration .......... A .......... ( 2) Further inspection
required.
Fails to accept and
hold charge ............ A ........ ( 3) Require replacement.
Fluid level low ......... B .......... ( 4) Further inspection
required.
Out of performance
specification
for battery ............ B ........ ( 5) Require replacement.
Out of specification for
application ............ B ........ ( 5) Require replacement.
Page 724 of 1691
Post (top or side) burned,
affecting performance .. A ........... (6) Require repair or
replacement.
Post (top or side) burned,
not affecting
performance ............ 2 ........... ( 6) Suggest repair or
replacement.
Post (top or side)
corroded, affecting
performance ............ A ................. Require repair.
Post (top or side)
corroded, not affecting
performance ............ 2 ................. Suggest repair.
Post (top or side)
loose .................. A ............ Require replacement.
Post (top or side)
melted, affecting
performance ............ A ........... ( 6) Require repair or
replacement.
Post (top or side)
melted, not affecting
performance ............ 2 ........... ( 6) Suggest repair or
replacement.
Specific gravity low .... B .......... ( 7) Further inspection
required.
State of charge low ..... A .......... ( 7) Further inspection
required.
Top dirty ............... 2 ....... Suggest cleaning battery.
Top wet ................. A ... ( 8) Require cleaning battery.
Further inspection required.
Vent cap loose .......... A ... Require repair or replacement
of vent cap.
Vent cap missing ........ C ..... Require replacement of vent
cap.
( 1) - DO NOT attempt to charge a frozen battery. Allow
battery to warm thoroughly and then performance-test.
If battery fails performance test, require replacement.
( 2) - No service suggested or required unless the battery
fails performance test, in which case, require
replacement.
( 3) - This phrase refers to a battery that fails to either
accept and/or retain a charge using appropriate times
listed in the Battery Charging Guide of the BCI Service
Manual, battery charger operating manual, or battery
manufacturer's specifications.
( 4) - Determine cause of low fluid level. Refill to proper
level(s) with water (distilled water preferred).
Recharge battery and performance-test.
( 5) - The battery may meet battery manufacturer's
specifications but test below the minimum
specification defined by the vehicle's OEM for
that vehicle.
( 6) - Determine cause and correct prior to repair or
replacement of part.
( 7) - Recharge and test to manufacturer's specifications.
If battery fails performance test, require replacement.
( 8) - Check fluid level and adjust to manufacturer's
specification. Suggest checking charging system
for proper operation.
\
\
\
\
\
\
\
BATTERY CABLES, WIRES AND CONNECTORS
Page 725 of 1691
![DODGE RAM 1999 Service Repair Manual BATTERY CABLE, WIRE AND CONNECTOR INSPECTION \
\
\
\
\
\
\
Condition](/img/12/56915/w960_56915-724.png "DODGE RAM 1999 Service Repair Manual BATTERY CABLE, WIRE AND CONNECTOR INSPECTION \
\
\
\
\
\
\
Condition")
BATTERY CABLE, WIRE AND CONNECTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Insulation damaged,
conductors exposed ..... A ........... ( 2) Require repair or
replacement.
Insulation damaged,
conductors not exposed . 1 ............ Suggest replacement.
Open .................... A .. Require repair or replacement.
Protective shield
(conduit) melted ....... 2 ........... ( 1) Suggest repair or
replacement.
Protective shield
(conduit) missing ...... 2 .. Suggest repair or replacement.
Resistance (voltage drop)
out of specification ... A .. Require repair or replacement.
Routed incorrectly ...... B ................. Require repair.
Secured incorrectly ..... B ................. Require repair.
Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Voltage drop out of
specification .......... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Exposed conductor at replacement (aftermarket) terminal
end does not require repair or replacement.
\
\
\
\
\
\
\
BATTERY CONNECTORS
See BATTERY CABLES, WIRES AND CONNECTORS .
BATTERY TRAYS AND HOLD DOWN HARDWARE
Page 726 of 1691
![DODGE RAM 1999 Service Repair Manual BATTERY TRAY AND HOLD DOWN HARDWARE INSPECTION \
\
\
\
\
\
\
Condition](/img/12/56915/w960_56915-725.png "DODGE RAM 1999 Service Repair Manual BATTERY TRAY AND HOLD DOWN HARDWARE INSPECTION \
\
\
\
\
\
\
Condition")
BATTERY TRAY AND HOLD DOWN HARDWARE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Battery improperly
secured ................ 2 ................. Suggest repair.
Bent, affecting
performance ............ A .. Require repair or replacement.
Bent, not affecting
performance ............ .. ....... No service suggested or
required.
Broken, affecting
performance ............ A .. Require repair or replacement.
Broken, not affecting
performance ............ .. ....... No service suggested or
required.
Corroded, affecting
performance ............ A .. Require repair or replacement.
Corroded, not affecting
performance ............ 2 .. Suggest repair or replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Missing ................. C ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Water drain clogged ..... A ................. Require repair.
\
\
\
\
\
\
\
BATTERY WIRES
See BATTERY CABLES, WIRES AND CONNECTORS .
BELT-DRIVEN AIR PUMPS
BELT-DRIVEN AIR PUMP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 ............ Suggest replacement.
Pulley alignment
incorrect .............. B .. Require repair or replacement.
Pulley bent ............. A ............ Require replacement.
Pulley cracked .......... A ............ Require replacement.
Pulley loose ............ A .. Require repair or replacement.
Pulley missing .......... C ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
Page 824 of 1691
pointer is at one o'clock position. Push in on knob slightly and
continue rotating knob to its full clockwise stop. Place knob pointer
at a position about .32" (8 mm) beyond end of Red stripe. Release
knob. If knob is pointing at about .32" (8 mm) beyond end of Red
stripe, go to next step. If knob is not pointing at about .32" (8 mm)
beyond end of Red stripe, go back to step 2) and repeat adjustment
procedure.
4) Rotate temperature control knob counterclockwise so that
knob pointer is at 12 o'clock position. Push temperature control knob
straight into heater control panel until perimeter of knob (not knob
pointer) is flush with base of heater control panel.
5) Rotate temperature control knob to its full clockwise
stop. Release knob. Knob pointer should be aimed at end of Red stripe.
If knob is pointed at end of Red stripe, go to next step. If knob is
not pointed at end of Red stripe, go back to step 2) and repeat
adjustment procedure.
6) Rotate temperature control knob to its full
counterclockwise stop. Release knob. If knob springs back, self-
adjuster clip securing temperature control cable to blend-air door
lever is improperly installed. See TEMPERATURE CONTROL CABLE R & I
under REMOVAL & INSTALLATION. If knob does not springs back,
temperature control cable adjustment is complete.
TROUBLE SHOOTING
HEATER PERFORMANCE
Check cooling system. Check serpentine drive belt tension.
Check radiator and radiator fan operation. Ensure that accessory
vacuum supply line is connected at power brake booster (Dakota) or
engine vacuum source (except Dakota).
TESTING
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
BLOWER MOTOR RELAYS
1) Blower motor relay is located in Power Distribution Center
(PDC). On Ram Van/Wagon, high speed blower motor relay is located in
engine compartment (on side of heater assembly). On all models,
disconnect negative battery cable. Remove blower motor relay. Using an
ohmmeter, check for continuity between terminals No. 87A and 30 of
relay. See Fig. 1. If continuity does not exist, replace relay. If
continuity exists, go to next step.
2) Using an ohmmeter, check for continuity between terminals
No. 30 and 87 of relay. If continuity exists, replace relay. If
continuity does not exist, go to next step.
3) Measure resistance between terminals No. 85 and 86 of
relay. Reading should be 70-80 ohms. If reading is not as specified,
replace relay. If reading is as specified, go to next step.
4) Using jumper wires, connect battery voltage to terminal
No. 86 and ground terminal No. 85. See Fig. 1. Check that continuity
exists between terminals No. 30 and 87. Check that continuity does not
exist between terminals No. 87A and 30. If continuity is not as
specified, replace blower motor relay. If continuity is as specified,
relay is okay.
Page 825 of 1691
Fig. 1: Identifying Blower Motor Relay Terminals
Courtesy of Chrysler Corp.
BLOWER MOTOR RESISTOR
1) Disconnect negative battery cable. Disconnect blower motor
resistor harness connector. Using an ohmmeter, check for continuity
between all blower motor resistor terminals. If continuity exists
between all terminals, go to next step. If continuity does not exist
between all terminals, replace faulty blower motor resistor.
2) Check for open or short in circuits between blower motor
resistor and heater control panel. Also check for open or short in
wire between blower motor resistor and blower motor.
BLOWER MOTOR SWITCH
Dakota, Durango & Ram Pickup
1) Using a voltmeter, check for battery voltage at underhood
power distribution center fuse No. 5 (40-amp) on Dakota and Durango;
fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to
next step. If battery voltage does not exist, check for open in Red
wire between battery and underhood power distribution center. If Red
wire is okay, replace underhood power distribution center.
2) Disconnect negative battery cable. Remove heater control
panel. See HEATER CONTROL PANEL R & I . Disconnect heater control panel
harness connector. Using an ohmmeter, check for continuity between
heater control panel harness connector terminal No. 7 (Black wire on
Dakota and Durango; Black/Orange on Ram Pickup) and ground. If
continuity exists, go to step 4).
3) If continuity does not exist, repair open in Black wire or
Black/Orange wire between heater control panel harness connector
terminal No. 7 and ground connector located at lower right corner of
instrument panel (Dakota and Durango) or behind center of instrument
panel (Ram Pickup).
4) Place heater mode control knob to any position except OFF.