brake DODGE RAM 1999 Service User Guide

from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.

6) Remove glove box. Reach through glove box opening and
disconnect antenna coaxial cable connector. Disconnect blower motor
connector located above glove box opening, near support brace for A/C-
heater housing. Disconnect radio ground strap. Loosen instrument panel
roll down bracket bolts about 2 turns, located at lower corners on
both sides of instrument panel. Remove 5 screws across top of dash
panel at base of windshield, removing center screw last.
7) Roll down instrument panel and install a temporary support
hook that is about 18" (457 mm) in length. Install hook from center
hole in instrument panel to center hole of dash panel. Pull lower
instrument panel outward until both roll down bracket bolts are in
slotted roll down position. Instrument panel should now be supported
and away from firewall.
8) Disconnect 2 door harness connectors, located on a bracket
near right end of instrument panel. Disconnect blower motor resistor.
Disconnect temperature control cable from A/C-heater housing and
remove from housing. See Fig. 5. Disconnect demister duct flexible
hose from A/C-heater housing.
9) Ensure instrument panel is free and clear for removal.
With the aid of an assistant, remove temporary support hook. Lift
instrument panel off of roll down bracket bolts and remove from
vehicle.
10) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.
Removal & Installation (Ram Pickup)
1) Disable air bag system. See AIR BAG SYSTEM SAFETY article.
Disconnect negative battery cable. Drain cooling system. Remove left
and right kick panel trim. Remove 5 screws and knee bolster/steering
column cover. Remove hood release and parking brake release handle
screws from lower instrument panel support. Remove 6 screws and
instrument panel support. Disconnect air bag connector at lower left
corner of instrument panel.
2) Pull PRNDL cable and twist to remove from position arm.
Push tab on bottom of cable retainer upward, then squeeze sides to
remove retainer from column. Remove tilt lever (tilt column only).
Remove both upper and lower shrouds from column. Remove lower fixed
column shroud. Loosen multifunction switch connector screw. Screw will
remain in connector.
3) Remove remaining steering column electrical connectors.
Remove air bag wiring harness from steering column wiring trough.
Remove wiring trough from steering column. Remove 3 toe plate nuts and
washers.
4) Remove 2 nuts and washers attaching steering column
bracket to instrument panel steering column support bracket. Allow
column to lower and rest on seat. Remove 2 screws from bottom of Air
Bag Control Module (ACM) cover. Remove 4 screws holding ACM to
transmission tunnel.
5) Disconnect wiring at ACM. Disconnect instrument panel left
side wiring connectors. Remove screw holding brake release to bottom
of instrument panel. Disconnect instrument panel right side wiring
connectors, which includes 2 connectors attached to A/C-heater
assembly housing, courtesy light connector, antenna cable and 2 body
connectors. Disconnect vacuum harness from A/C-heater system.
6) Remove 5 screws holding instrument panel to dash. Loosen
lower instrument panel pivot bolts. Roll instrument panel downward.
Remove instrument panel from vehicle.
7) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.

BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument

vacuum reading of 26 in. Hg or more. Close all valves and turn vacuum
pump off. Observe vacuum gauge, go to next step.
2) If A/C system maintains specified vacuum for 5 minutes,
open low-side and high-side valves, restart vacuum pump and operate
for an additional 10 minutes. Close all valves. Turn vacuum pump off
and disconnect pump.
3) If A/C system cannot get to or maintain specified vacuum,
check for a defective vacuum pump or leak in A/C system or gauge set.
See LEAK TESTING. Repair or replace components as necessary.
CHARGING A/C SYSTEM
* PLEASE READ THIS FIRST *
CAUTION: During charging of A/C system, refrigerant container must be
in an upright position. If refrigerant container is
upside down, compressor may be damaged by liquid refrigerant
drawn into A/C system.
CHRYSLER CORP.
Avenger 2.0L & Sebring Coupe 2.0L
1) Ensure A/C system has no leaks and has been evacuated. See
EVACUATING A/C SYSTEM and LEAK TESTING. Locate sight glass on
receiver-drier and ensure it is clean. Close low-pressure adapter
valve and remove from manifold gauge set.
2) Connect low-pressure adapter valve to refrigerant
container and open container valve. Ensure Blue charging hose is
properly connected to vehicle low-pressure service valve. Open adapter
valve.
3) If refrigerant is not drawn in, fully close adapter valve
and check for hose connection leaks. If leak is detected, retighten
connections and repeat A/C system evacuation. See EVACUATING A/C
SYSTEM.
4) If refrigerant is drawn in, start engine. Turn A/C on and
set temperature control to maximum cold and blower motor to low speed.
Operate engine at 1500 RPM. As refrigerant is drawn into system, foam
or bubbles will appear in sight glass.
5) System charge will be close to full when sight glass is
clear, compressor clutch is engaged, and compressor suction and
discharge line temperatures are similar. System charge will be
complete when sight glass is clear, compressor clutch is engaged,
compressor discharge line is warm and suction line is cool.
6) When proper amount of refrigerant has been added, stop
engine. Close refrigerant container and adapter valve, and disconnect
gauge set.
Breeze, Cirrus, Concorde, Intrepid, LHS, Stratus & 300M (Scan
Tool Method)
1) Attach Diagnostic Readout Box (DRB) to Data Link Connecto\
r
(DLC). Set DRB (scan tool) to PARTIAL CHARGE TEST. Attach clamp-on
Thermocouple (80PK-1A) to liquid line, as close to condenser outlet as\
possible.
2) Set parking brake, and place transaxle in Park position.
Start engine and allow to idle. Set A/C controls to outside air, panel
mode, full cool, and high blower speed. Turn A/C on, and open vehicle
windows. Operate A/C system for a few minutes to allow system to
stabilize.
3) Place cardboard over front grille area, to block airflow
through part of condenser, to set A/C system pressure to 260 psi (18.3
kg/cm
). This will stop cooling fans from alternating speeds and
maintain constant pressure.

4) Scan tool will automatically calculate system charge.
Depending on system charge condition, corrections are made 2 ounces at
a time. Each time a correction is made, recheck readings to ensure
proper charge. For system refrigerant capacity, see REFRIGERANT OIL &
REFRIGERANT SPECIFICATIONS article.
Breeze, Cirrus, Concorde, Intrepid, LHS, Stratus & 300M
(Manifold Gauge Set Method)
1) Attach clamp-on Thermocouple (80PK-1A) to liquid line, as\
close to condenser outlet as possible. Attach manifold gauge set to
vehicle.
2) Set parking brake, and place transaxle in Park position.
Start engine and allow to idle. Set A/C controls to outside air, panel
mode, full cool, and high blower speed. Turn A/C on, and open windows.
Operate system for a few minutes to allow system to stabilize.
3) Place cardboard over front grille area, to block airflow
through part of condenser, to set A/C pressure to 260 psi (18.3
kg/cm
). This will stop cooling fans from alternating speeds and
maintain constant pressure.
4) Record temperature reading at liquid line and discharge
pressure reading on gauges. Compare readings with values in
REFRIGERANT CHARGE LEVEL table.
5) Depending on system charge condition, corrections are made
2 ounces at a time. Each time a correction is made, recheck readings
to ensure proper charge. For system refrigerant capacity, see
REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS article.
REFRIGERANT CHARGE LEVEL









\









\









\









\









\









\









\








Liquid Line Temp. ( 1) Discharge PressureF (C) psi (kg/cm)
40 (4.4) ........................................... 53-75 (3.7-5.3\
)
60 (15.6) ......................................... 81-104 (5.7-7.3\
)
80 (26.7) ....................................... 111-142 (7.8-10.0\
)
100 (37.8) ..................................... 156-194 (11.0-13.6\
)
120 (48.9) ..................................... 208-259 (14.6-18.2\
)
140 (60.0) ..................................... 272-331 (19.1-23.3\
)
160 (71.1) ..................................... 353-420 (24.8-29.5\
)
180 (82.2) ..................................... 447-516 (31.4-36.3\
)
( 1) - When pressure is lower than specified, system is undercharged.
When pressure is higher than specified, system is overcharged.









\









\









\









\









\









\









\








All Other Models
Ensure A/C system has been checked for leaks and evacuated.
See EVACUATING A/C SYSTEM and LEAK TESTING. Charge A/C system to
specifications. For system refrigerant capacity, see REFRIGERANT OIL &
REFRIGERANT SPECIFICATIONS article.
FORD MOTOR CO.
1) If using approved Recovery/Recycling/Charging Center (023-\
00105 or 023-00150), connect to high-side and low-side service valves.
See SERVICE VALVE LOCATIONS under SYSTEM SERVICE VALVES. Operate
charging center according to manufacturer's instructions. Charge
system with specified amount of refrigerant and refrigerant oil. See
REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS article. Check amount of
refrigerant oil in system before adding oil. See COMPRESSOR
REFRIGERANT OIL CHECKING article.
2) If using manifold gauge set, connect to high-side and low-
side service valves. See SERVICE VALVE LOCATIONS under SYSTEM SERVICE

damage clockspring and/or require clockspring to be
readjusted.
NOTE: Clockspring is self-centering and will automatically lock in
the centered position when steering wheel is removed.
Adjustment is only required if centering position is
disturbed.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Clockspring is located behind steering wheel. See Fig. 1.
Ensure front wheels are in straight-ahead position. Lock steering
wheel. Remove air bag module. See AIR BAG MODULE.
3) Remove steering wheel nut. Using appropriate steering
wheel puller, remove steering wheel. When steering wheel is removed,
self-centering clockspring will automatically lock in place. Remove
upper and lower steering column shrouds to gain access to clockspring
wiring.
4) Remove knee bolster (if equipped). Disconnect Yellow 2-wa\
y
clockspring harness connector between clockspring and instrument panel
wiring harness, at base of steering column. See Fig. 13. Remove
clockspring by releasing 2 tabs on side of clockspring. Clockspring
cannot be repaired and must be replaced if faulty.
Installation
1) Snap clockspring onto steering column. If clockspring
centering adjustment is disturbed, adjust clockspring before
installing steering wheel. See CLOCKSPRING CENTERING under
ADJUSTMENTS. Connect clockspring wiring connectors. Install steering
column covers. Install knee bolster (if removed).
2) Position steering wheel on steering column. Ensure flats
on steering wheel hub fit formations on inside of clockspring. Pull
clockspring, cruise control switch (if equipped) and horn wires
through lower large holes and upper small holes in steering wheel.
3) Install steering wheel retaining nut and tighten to 45 ft.
lbs. (61 N.m). Connect horn and cruise control wires (if equipped).
Connect clockspring wire to air bag module. To ensure complete
connector connection, latching arms must be visible on top of
connector housing. DO NOT connect negative battery cable at this time.
Go to SYSTEM OPERATION CHECK .
PASSENGER AIR BAG DISARM (PAD) SWITCH
Removal & Installation
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) If vehicle is equipped with automatic transmission, turn
ignition switch to UNLOCK position, set parking brake and place
transmission selector lever in LOW position. Tilt steering column to
lowest position (if equipped). Using trim stick, gently pry around
perimeter of cluster bezel and remove bezel.
3) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
4) Reach through glove box opening to access and disconnect 2
passenger-side air bag disarm switch harness connectors. Connectors
are attached to bracket located on inboard glove box opening
reinforcement. See Fig. 4. Remove 3 screws retaining passenger-side
air bag disarm switch bezel to instrument panel.

inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Ensure ignition switch is in the RUN position. Disconnect
Powertrain Control Module (PCM) connectors. If DRB does not display
BUS SHORT TO BATTERY, to step 8). If DRB displays BUS SHORT TO
BATTERY, go to next step.
2) Disconnect instrument cluster connectors. If DRB does not
display BUS SHORT TO BATTERY, replace instrument cluster. If DRB
displays BUS SHORT TO BATTERY, go to next step.
3) Turn ignition off and wait 2 minutes before proceeding.
Disconnect air bag control module connector. Turn ignition on (engine
off). If DRB does not display SHORT TO BATTERY, replace ACM. If DRB
displays SHORT TO BATTERY, go to next step.
4) Disconnect Central Timer Module (CTM) 18-pin connector. I\
f
DRB does not display BUS SHORT TO BATTERY, replace CTM. If DRB
displays BUS SHORT TO BATTERY, go to next step.
5) Disconnect anti-lock brake controller. If DRB does not
display BUS SHORT TO BATTERY, replace anti-lock brake controller. If
DRB displays BUS SHORT TO BATTERY, go to next step.
6) Disconnect DRB from Data Link Connector (DLC). Using a
voltmeter, check voltage between ground and DLC connector terminal No.
3 (Violet/Brown wire). If voltage is more than 0.2 volt, repair short
in Violet/Brown wire. If voltage is less than 0.2 volt, go to next
step.
7) Using a voltmeter, check voltage between ground and DLC
connector terminal No. 11 (White/Black wire). If voltage is more than
0.2 volt, repair short in White/Black wire. If voltage is less than 0.
2 volt, replace DRB or DRB cable as necessary.
8) Turn ignition off. Using an ohmmeter, check resistance
between ground and PCM Black connector terminal A31 (Black/Tan wire).
If resistance is more than 10 ohms, repair open in Black/Tan wire). If
resistance is less than 10 ohms, go to next step.
9) Using an ohmmeter, check resistance between ground and PCM
Black connector terminal A32 (Black/Tan wire). If resistance is more
than 10 ohms, repair open in Black/Tan wire). If resistance is less
than 10 ohms, replace Powertrain Control Module (PCM).
NO RESPONSE FROM INSTRUMENT CLUSTER
NOTE: Perform COMPONENT VERIFICATION TEST under DIAGNOSTIC TESTS
after all repairs. Each time a connector is disconnected,
inspect it to ensure it is in good condition. Always focus on
circuit being tested. Dirt, water and corrosion, are most
common problems in connectors. Due to manufacturer changes in
wire colors, use terminal identification whenever possible.
1) Remove Instrument cluster. Using DRB, turn on INTERNAL BUS
BIAS under SYSTEM MONITORS CCD BUS VOLTAGE. Connect a jumper wire from
Black instrument cluster 10-pin connector "A" terminal No. 9
(White/Black wire) to ground. Observe CCD BUS voltage on DRB. If
voltage did not drop to about zero volt, repair open in White/Black
wire. If voltage drops to about zero volt, go to next step.
2) Leave internal DRB CCD BUS BIAS turned on. Connect a
jumper wire from ground to Black instrument cluster 10-pin connector
"A" terminal No. 10 (Violet/Brown wire). Go to next step.
3) Observe CCD BUS voltage on DRB. If voltage did not drop to
about zero volt, repair open in Violet/Brown wire. If voltage drops to
about zero volt, replace instrument cluster.

AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).

* PLEASE READ THIS FIRST *
NOTE: For engine-related DTCs, see appropriate SELF-DIAGNOSTICS
article in ENGINE PERFORMANCE. Engine performance DTCs must
be repaired first, as engine performance and related
component signals will affect transmission operation and
diagnosis.
All references to Using scan tool, perform TCC SYSTEM TEST
are for scan tool driven testing of TCC system. Follow manufactures
scan tool instructions.
All connector references in the following testing apply to
harness connectors unless otherwise specified. For circuit, wire color
and connector terminal identification, see CONNECTOR IDENTIFICATION
and WIRING DIAGRAMS. After all repairs are complete or any component
is replaced, perform verification test as follows:
* DTC P0751 perform appropriate verification VER-2A.
* All DTCs except P0751 perform appropriate verification
VER-5A.
DTC P0711: TRANS TEMP SENSOR, NO TEMP RISE AFTER START
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
1) Using scan tool, read DTCs. If DTCs P0712, P0713 or P1899
are present, repair these DTCs before proceeding. If neither of these
DTCs are present, go to next step.
2) Using scan tool, read and record Engine Coolant
Temperature (ECT) sensor temperature, and transmission temperature
sensor temperature. If transmission temperature is within 9
F (-13C)
of ECT temperature, go to step 5). If transmission temperature is not
within 9
F (-13C) of ECT temperature, go to next step.
3) Start engine and let it idle in gear, with brake on.
Monitor transmission temperature sensor. If transmission temperature
does not increase steadily 15
F (-9C) over a 10 minute period, go to
step 5). If transmission temperature increases steadily 15F (-9C)
over a 10 minute period, go to next step.
4) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
5) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, replace transmission governor
pressure/temperature sensor.
DTC P0712: TRANS TEMP SENSOR VOLTAGE TOO LOW
Circuit Description
Circuit is monitored continuously while key is on, and engine
running. Code sets if transmission temperature sensor voltage is less
than 1.55 volts for 2.2 seconds.
Possible Causes
* Transmission temperature sensor wiring harness defective.
* Transmission pressure/temperature sensor defective.
* Transmission temperature signal circuit short to ground.
* Transmission temperature signal circuit short to sensor
ground circuit.
* PCM defective.

between Black PCM harness connector C1 and transmission
pressure/temperature sensor harness connector. If resistance is
greater than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or less, replace
transmission pressure/temperature sensor.
10) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is greater than 3.76 volts, replace
PCM. If voltage is 3.76 volts or less, conditions required to set DTC
P0713 are not present at this time. DTC P0713 sets when transmission
temperature sensor voltage at PCM is greater than 3.76 volts for 2.2
seconds. Possible causes are: open transmission temperature sensor
wiring, faulty connections, faulty transmission temperature sensor or
faulty PCM. Go to next step.
11) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P0720: LOW OUTPUT SPEED SENSOR RPM ABOVE 15 MPH (EXCEPT
BR BODY)
Circuit Description
Circuit is monitored continuously while key is on, and gear
selector is not in Park or Neutral. Code sets if vehicle speed is
above 15 MPH and output shaft speed is below 60 RPM for 2.6 seconds as
measured from vehicle speed sensor.
Possible Causes
* Open output speed sensor ground circuit.
* Damaged ignition wiring.
* Open output speed sensor signal circuit.
* Short to ground in output speed sensor signal circuit.
* Park/Neutral switch code present.
* Malfunctioning sensor.
* Short to ground in output speed sensor ground circuit.
* Malfunctioning PCM.
* OSS harness intermittent defective.
Diagnostic Procedure
1) Using scan tool, check SPECIFIC GOOD TRIPS counter. If DTC
SPECIFIC GOOD TRIPS counter is not displayed or displayed count is not
"0", go to step 12). If DTC SPECIFIC GOOD TRIPS counter is displayed
and displayed count is "0", go to next step.
2) Record all DTCs and one trip failures. If DTC P1899 is
present, repair P/N switch code first. See DTC P1899: P/N SWITCH STUCK
IN PARK OR ON GEAR. If DTC P1899 is not present, go to next step.
3) Raise and support vehicle. Using scan tool, erase DTCs.
See CLEARING DIAGNOSTIC TROUBLE CODES. Start engine. Place engine in
1st gear. Using scan tool, read output speed sensor. Release brake and
let wheels roll, keeping speed below 15 MPH. If scan tool shows 60 RPM
or less, go to step 6). If scan tool shows greater than 60 RPM, go to
next step.
4) While monitoring output speed sensor, wiggle harness
between output speed sensor and PCM. If reading dropped towards zero
while wiggling harness, repair intermittent short or open in harness.
If reading does not drop towards zero while wiggling harness, go to
next step.
5) Using scan tool, erase DTCs. See CLEARING DIAGNOSTIC
TROUBLE CODES. Road test vehicle. If code returns, there are no other
potential causes. Replace PCM. If code does not return, testing is
complete.
6) Turn ignition off. Disconnect PCM and output speed sensor
harness connectors and inspect for damage. Repair as necessary. If no