brake light DODGE RAM 1999 Service User Guide
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 325 of 1691
system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.
\
\
\
\
\
\
\
BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.
\
\
\
\
\
\
\
BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Page 344 of 1691
specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal
particles or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable; check
for accepted cleaning procedure.
\
\
\
\
\
\
\
STEEL BRAKE LINES
STEEL BRAKE LINE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Fitting incorrect (for
example, compression
fitting) ............... B ............ Require replacement.
Flare type incorrect .... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Line material incorrect
(copper, etc.) ......... B ............ Require replacement.
Restricted .............. A ............ Require replacement.
Routed incorrectly ...... B ..... Require routing correction.
Rust-pitted ............. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\
STOPLIGHT SWITCHES
See BRAKE STOPLIGHT SWITCHES .
SWITCHES
NOTE: Copied from Electrical UIGs & added "float saturated" from
old fluid level sensor switches.
STEEL BRAKE LINE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 354 of 1691
![DODGE RAM 1999 Service User Guide \
\
\
\
\
\
\
Application](/img/12/56915/w960_56915-353.png "DODGE RAM 1999 Service User Guide \
\
\
\
\
\
\
Application")
\
\
\
\
\
\
\
Application psi (kg/cm)
All Models ....................................... 10-15 (1.06-1.41)\
\
\
\
\
\
\
\
NOTE: When bleeding disc brakes, air may tend to cling to caliper
walls. Lightly tap caliper while bleeding to aid in removal
of air.
Manual Bleeding
1) Fill master cylinder. Install bleeder hose on first
bleeder valve to be serviced. See BLEEDING SEQUENCE table. Submerge
other end of hose in clean glass jar partially filled with clean brake
fluid.
NOTE: When bleeding brake system manually, ensure bleeder valve is
closed when brake pedal is released.
2) Open bleeder valve 3/4-1 turn. Depress brake pedal slowly
through full travel. Close bleeder valve. Release pedal. Repeat
procedure until fluid flow is free of air bubbles.
ADJUSTMENTS
PARKING BRAKE
1) Release parking brake, and loosen cable adjusting nut to
allow slack in cable. Adjust rear brakes. Tighten cable adjusting nut
until a slight drag is felt while rotating rear wheels.
2) Loosen cable adjusting nut until both rear wheels can be
rotated freely. Back off adjusting nut an additional 2 turns. Apply
and release parking brake several times, checking for free rotation at
rear wheels.
REAR BRAKE SHOES
1) Raise and support vehicle. Ensure parking brake lever is
fully released. Back off parking brake cable adjustment to ensure
cable has slack. Remove adjusting hole cover.
2) Using a brake adjuster, expand brake shoes until slight
drag is felt when wheel assembly is rotated. Using thin screwdriver,
hold automatic adjusting lever away from adjustment star wheel.
3) Back off adjustment star wheel until wheel assembly
rotates freely and brake shoe drag is eliminated. Repeat adjustment
for remaining wheels. Adjustment must be equal at all wheels. Replace
adjusting hole covers. Adjust parking brake. See PARKING BRAKE.
STOPLIGHT SWITCH
Stoplight switch is attached to brake pedal support. Push
stoplight switch through clip in mounting bracket until switch seats
in bracket. Pull brake pedal backward as far as pedal will travel.
Brake pedal will ratchet stoplight switch to correct position. Verify
full brake pedal return, and that stoplights glow when brake pedal is
applied.
TESTING
POWER BRAKE BOOSTER FUNCTIONAL TEST
Page 355 of 1691
1) Start engine, and check booster vacuum hose connections. A
hissing noise indicates a vacuum leak. Repair any vacuum leaks before
proceeding. Stop engine, and shift transmission into Neutral. Pump
brake pedal until all vacuum reserve in booster is depleted.
2) Hold brake pedal under light pressure. If pedal does not
hold firm and falls away, master cylinder may be faulty. Bleed system
using appropriate method, and repeat step 1). See BLEEDING PROCEDURES
under BLEEDING BRAKE SYSTEM.
3) If pedal still does not hold firm, master cylinder is
faulty. If pedal holds firm, start engine and observe pedal height. If
pedal height change is not apparent, power booster or vacuum check
valve is faulty. Install good check valve, and repeat steps 1) and 2).\
If pedal falls away slightly under light pressure and then holds firm,
go to next step .
4) Start engine. Release brake pedal. Increase engine speed
to 1500 RPM. Close throttle and immediately turn off ignition. Wait at
least 90 seconds, and try brake action again. Booster should provide 2
or more vacuum assisted pedal applications. If vacuum assist is not
provided, perform booster and check valve vacuum tests.
POWER BRAKE BOOSTER VACUUM TEST
Connect vacuum gauge to booster check valve using "T"
fitting. Start engine, and run at idle speed for one minute. Clamp
hose shut between vacuum source and check valve. Stop engine, and
observe vacuum gauge. If vacuum drops more than one in. Hg within 15
seconds, booster diaphragm or check valve is faulty.
POWER BRAKE BOOSTER CHECK VALVE TEST
Disconnect vacuum hose from check valve. Remove check valve
and valve seal from booster. Use a hand-operated vacuum pump for
testing. Apply 15-20 in. Hg at large end of check valve. Vacuum should
hold steady. If gauge on pump indicates vacuum loss, check valve is
faulty and should be replaced.
COMBINATION VALVE METERING VALVE TEST
Metering valve operation can be checked visually with aid of
an assistant. While an assistant applies and releases brake pedal,
observe metering valve stem. If valve is operating correctly, stem
will extend slightly when brakes are applied, and contract when brakes
are released. If valve is faulty, replace combination valve assembly.
COMBINATION VALVE PRESSURE DIFFERENTIAL SWITCH TEST
1) Using an assistant, apply brake pedal. Observe brake
warning light. Raise and support vehicle, and connect a bleed hose to
one rear wheel cylinder. Submerge other end of hose into container
partially filled with brake fluid. Have assistant press and hold brake
pedal down while observing brake warning light. Open bleeder screw. If
warning light glows, switch is operating properly.
2) If warning light fails to glow, check circuit fuse, bulb
and wiring. Repair as necessary. Repeat step 1). If warning light
fails to glow, check brakelight, parking brake switches and related
wiring. Repair as necessary. Repeat step 1). If warning light fails to
glow, pressure differential switch is faulty. Replace combination
valve assembly, and bleed brake system. Verify proper valve operation.
REMOVAL & INSTALLATION
Page 358 of 1691
pads at this time. On models with removable hub, install hub on rotor.
Install wheel and tire assembly. Tighten lug nuts so they are snug,
but DO NOT tighten to final torque specifications.
3) While rotating wheel, tighten adjuster nut sufficiently to
seat bearing. Loosen nut and retighten while still rotating wheel.
Back off adjuster nut to completely release bearing preload torque.
Ensure endplay of .001-.003" (.025-.076 mm). Install lock nut and NEW
cotter pin. If necessary, tighten lock nut slightly to align cotter
pin hole. Install grease cap. Tighten caliper bolts and lug nuts to
specification. See TORQUE SPECIFICATIONS table. To complete
installation, reverse remove procedure.
Removal (Ram Pickup With 8 Studs)
1) Raise and support vehicle. Remove wheel. Remove hub
extension, if equipped. Remove brake caliper. Support caliper aside.
2) On models with removable adapter hub, remove hub from
rotor. On models with one-piece hub and rotor assembly, remove cotter
pin from rotor hub nut. Remove nut. Disconnect ABS wheel speed sensor
wire (if equipped), and remove from frame and steering knuckle. Remove\
bolts securing hub to steering knuckle from inboard side of steering
knuckle. Remove rotor and hub assembly.
Installation
1) Apply anti-seize compound to drive shaft splines. Replace
grease seal in steering knuckle, if necessary. Insert 2 rearmost top
and bottom rotor hub bolts in steering knuckle so they extend through
back of knuckle. Install hub spacer, ensuring flat on space is
positioned to rear. Use chassis grease to hold spacer in position, if
necessary.
NOTE: If equipped with wheel speed sensor, brake shield must be
positioned on hub bearing, and sensor wire must be at top of
knuckle.
2) Align rotor hub with drive shaft and install hub assembly.
Align bolt holes in hub flange with bolts previously installed. Start
nuts on flange bolts sufficiently to hold assembly in place. Install
remaining bolts, and tighten all bolts to specification. See TORQUE
SPECIFICATIONS table.
3) Install washer and hub nut. Tighten nut securely. Install
NEW cotter pin. Install grease cap. Install caliper. Tighten caliper
bolts and lug nuts to specification. See TORQUE SPECIFICATIONS table.
To complete installation, reverse remove procedure.
REAR BRAKE SHOES
WARNING: Use water or brake cleaner to clean brake parts. DO NOT use
compressed air to remove dirt and dust.
Removal (Dakota & Ram Van)
1) Remove wheel and drum. Note how secondary spring overlaps
primary return spring. Using spring remover, remove brake shoe return
springs. Slide automatic adjuster cable off anchor. Disconnect cable
from adjusting lever.
2) Remove cable, cable guide and anchor plate. See Figs. 3,
4, and 5. Disconnect adjusting lever return spring from lever. Remove
lever and return spring from pivot pin. Remove shoe-to-shoe spring.
Spread shoes, and remove adjustment star wheel.
3) Remove shoe retainers, springs and pins. Remove parking
brake lever from secondary shoe. Remove shoes and parking brake strut
with spring.
Page 363 of 1691
being replaced, remove booster check valve and seal.
Installation
1) If new booster is being installed, install check valve and
seal. Position booster on dash, and install lock nuts on booster
mounting studs finger tight. Install booster push rod on brake pedal
pin, and secure rod with NEW retaining clip.
2) Tighten booster lock nuts to specification. Install master
cylinder on booster, and tighten mounting nuts to specification. See
TORQUE SPECIFICATIONS table. Connect vacuum hose to booster check
valve. Start vehicle and check booster operation.
COMBINATION VALVE
Removal & Installation
Raise and support vehicle. Mark brakelines for assembly
reference. Disconnect parking brake cable from clip on valve, if
necessary. Disconnect brake warning light connection at switch.
Disconnect all brake hydraulic lines at valve. Cap brakelines to
prevent dirt from entering system. Remove valve. To install, reverse
removal procedures. Bleed brake system. See BLEEDING PROCEDURES under
BLEEDING BRAKE SYSTEM.
AXLE BEARING & SEAL (FULL FLOATING AXLE)
Removal & Installation (Ram Pickup With 12" & 13" Drums)
1) Raise and support vehicle. Remove wheel. Remove axle shaft
nuts and washers. Strike center of axle flange to free cones. Remove
axle shaft and gasket.
2) Straighten and remove nut lock. Remove adjustment nut and
outer bearing. Remove drum assembly. Remove seal and inner bearing
from drum assembly.
3) Pack inner bearing, and install inner bearing and seal in
drum. Install drum assembly, outer bearing and adjustment nut. While
rotating drum, tighten adjustment nut to specification. See TORQUE
SPECIFICATIONS table.
4) Back off adjustment nut 1/8 turn to obtain .001-.010" (0.
025-0.254 mm) end play. Bend nut lock into spindle keyway. Install
gasket and axle shaft. Install wheel, and lower vehicle. See TORQUE
SPECIFICATIONS table.
OVERHAUL
NOTE: Use illustrations when overhauling components. See
Figs. 2-6.
DISC BRAKE SPECIFICATIONS
DISC BRAKE SPECIFICATIONS \
\
\
\
\
\
\
Application In. (mm)\
Disc Diameter
Dakota ............................................... 11.30 (287)\
Ram Pickup
1/2 Ton ............................................. 11.57 (294)\
3/4 & 1 Ton ......................................... 12.50 (318)\
Ram Van
1/2 & 3/4 Ton ....................................... 11.75 (299)\
1 Ton ............................................... 12.82 (326)\
Lateral Runout
Page 391 of 1691
10.4 volts. FTC P1595 will set if vacuum and vent solenoids do not
respond when actuated by PCM.
Possible Causes:
* Ground circuit open.
* S/C brake switch output circuit open.
* S/C power supply circuit open or shorted.
* S/C servo defective.
* S/C vacuum solenoid control circuit open or shorted.
* S/C vent solenoid control circuit open or shorted.
* Brake switch defective or out of adjustment.
* Defective PCM.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
1) Turn ignition on. Turn Speed Control (S/C) on. Using scan\
tool, actuate S/C vent solenoid. If speed control servo clicks, go to
next step. If S/C servo does not click, go to step 7).
2) Using scan tool, actuate S/C vacuum solenoid. If S/C servo
clicks, go to next step. If S/C servo does not click, go to step 6).
3) Turn ignition on. Using scan tool, actuate S/C vacuum
solenoid. Wiggle wiring harness between S/C servo and brake switch to
PCM while scan tool is still actuating speed control vacuum solenoid.
If wiggling did not cause an interruption of S/C servo actuation, go
to next step. If wiggling caused an interruption of S/C servo
actuation, repair wiring harness as necessary. Perform TEST VER-4A
under VERIFICATION TESTS.
4) Turn ignition off. Inspect S/C wiring and connectors.
Clean or repair as necessary. Perform TEST VER-4A under VERIFICATION
TESTS. If wiring and connectors are okay, go to next step.
5) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, test is complete. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
6) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, go to next step. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
7) Turn ignition off. Disconnect S/C servo 4-pin connector.
Inspect all related wiring and connectors and repair as necessary.
Turn ignition on. Turn S/C switch on. Using a 12-volt test light,
probe brake switch output circuit at S/C servo connector terminal No.
3 (Dark Blue/Red wire). If test light is illuminated and bright, go to\
next step. If test light is dim or not illuminated, go to step 13).
8) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
9) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance between ground and
S/C vacuum solenoid control circuit at S/C servo connector terminal
Page 392 of 1691
No. 1 (Tan/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
10) Using an ohmmeter, check resistance between ground and
S/C vent solenoid control circuit at S/C servo connector terminal No.
2 (Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, go to next step.
11) Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between S/C servo connector terminal No. 1
and PCM connector C3, terminal No. 4 (Tan/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
12) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between S/C servo connector terminal No. 2 and PCM
connector C3, terminal No. 5 (Light Green/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace S/C
servo. Perform TEST VER-4A under VERIFICATION TESTS.
13) Using an ohmmeter, check resistance between ground and
brake switch output circuit at S/C servo connector terminal No. 3
(Dark Blue/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
14) Reconnect PCM. Disconnect brake switch connector. Turn
ignition on. Turn S/C on. Using a 12-volt test light, probe S/C power
supply circuit at brake switch connector terminal No. 3 (Yellow/Red
wire). If test light is illuminated and bright, go to next step. If
test light is not illuminated or dim, go to step 17).
15) Turn ignition off. Using an ohmmeter, check resistance of
S/C brake switch output circuit between S/C servo connector terminal
No. 3 and brake switch connector terminal No. 4 (Dark Blue/Red wire).
If resistance is 5 ohms or more, repair open circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
16) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, replace
brake switch. Perform TEST VER-4A under VERIFICATION TESTS.
17) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance of
S/C power supply circuit between PCM connector C3, terminal No. 11 and
brake switch connector terminal No. 3 (Yellow/Red wire). If resistance\
is 5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace PCM.
Perform TEST VER-4A under VERIFICATION TESTS.
FTC P1596: SPEED CONTROL SWITCH ALWAYS HIGH
FTC P1596 will set if an open circuit is detected in Speed
Control (S/C) switch circuit when ignition is on.
Possible Causes:
* Defective clockspring.
* S/C switch ground circuit open.
* Defective ON/OFF switch.
* Defective PCM.
* S/C switch signal circuit open or shorted to voltage.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
Page 394 of 1691
voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next
Page 395 of 1691
step. If test light is dim or not illuminated, go to step 7).
2) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
3) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between PCM connector C3, terminal No. 4 and
S/C servo connector terminal No. 1 (Tan/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
4) Using an ohmmeter, check resistance between ground and S/C
vacuum solenoid control circuit at S/C servo connector terminal No. 1
(Tan/Red wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
5) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between PCM connector C3, terminal No. 5 and S/C servo
connector terminal No. 2 (Light Green/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
6) Using an ohmmeter, check resistance between ground and S/C
vent solenoid control circuit at S/C servo connector terminal No. 2
(Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, replace S/C servo. Perform TEST VER-4A
under VERIFICATION TESTS.
7) Turn ignition off. Disconnect brake switch connector.
Inspect connectors. Clean or repair as necessary. Turn ignition on.
Using scan tool, actuate S/C solenoid. Using a 12-volt test light,
probe S/C power supply circuit at brake switch connector terminal No.
4 (Yellow/Red wire). If test light is illuminated and bright, go to
next step. If test light is not illuminated or dim, go to step 10).
8) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, go to
next step.
9) Using an ohmmeter, check resistance of brake switch output
circuit between brake switch connector terminal No. 3 and S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is more
than 5 ohms, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or less, replace brake
switch. Perform TEST VER-4A under VERIFICATION TESTS.
10) Turn ignition off. Using an ohmmeter, check resistance
between ground and S/C brake switch output circuit at S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
11) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance of S/C power supply
circuit between PCM connector C3, terminal No. 11 and brake switch
connector terminal No. 4 (Yellow/Red wire). If resistance is 5 ohms or\
more, repair open circuit. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is less than 5 ohms, replace PCM. Perform TEST
VER-4A under VERIFICATION TESTS.
FTC P1899: PARK/NEUTRAL POSITION (PNP) SWITCH STUCK IN PARK
OR IN GEAR (A/T MODELS)
Possible Causes: