warning light DODGE RAM 1999 Service User Guide

13) On A/T models, ensure all electrical connectors are clean
and properly connected to electrical plugs on transmission case. On
all models, check for loose or defective electrical connections on
starter and starter solenoid.
MECHANICAL INSPECTION
Compression
Manufacturer does not provide information for checking
compression.
FUEL SYSTEM
AIR IN FUEL SYSTEM
NOTE: Air in the fuel system may cause hard starting, rough
running, excessive smoke, poor engine performance, engine
misfire, poor fuel economy and fuel knock. Air may enter fuel
system whenever fuel supply lines, fuel filter/water
separator, fuel injection pump, fuel injectors or high
-pressure fuel lines are removed or disconnected.
1) Inspect all low-pressure fuel lines from fuel tank to fuel
transfer pump, fuel heater and fuel filter/water separator for signs
of leakage. Inspect all high-pressure fuel lines for signs of leakage.
See FUEL INJECTOR & HIGH-PRESSURE FUEL LINES under FUEL SYSTEM.
2) After repairing fuel leak, bleed air from fuel system. See
FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article.
FUEL HEATER
1) Fuel heater is located in fuel filter/water separator. See
Fig. 1 . Fuel heater uses a fuel heater temperature sensor for
controlling operation of the fuel heater.
2) A defective fuel heater may cause excessive wax build-up
in the fuel filter/water separator during cold ambient temperatures.
Wax build-up may cause hard starting, prevent engine from
accelerating, low power, Blue smoke or White smoke. For testing of
fuel heater and fuel heater temperature sensor, see SYSTEM & COMPONENT
TESTING - TRUCKS - DIESEL article.
FUEL HEATER RELAY
Ensure fuel heater relay, located in power distribution
center is installed correctly and that terminals are not corroded. For
fuel heater relay testing, see SYSTEM & COMPONENT TESTING - TRUCKS -
DIESEL article.
FUEL FILTER/WATER SEPARATOR
NOTE: A blocked or restricted fuel filter/water separator may cause
starting problems, prevent engine from accelerating, low
power or White smoke. If an excessive amount of water
collects in filter/separator in a short period of time, it
may be necessary to drain and clean fuel tank.
1) When ignition switch is first turned to ON position,
WATER-IN-FUEL (WIF) warning light should come on for 2 seconds to
perform bulb and wiring circuit test and then go off. WATER-IN-FUEL
(WIF) warning light is located on instrument panel, just below the

tachometer.
2) If WATER-IN-FUEL (WIF) warning light stays on, water
should be drained from fuel filter/water separator. To drain water
from fuel filter/water separator, ensure engine is not running. Place
drain pan below drain tube at fuel filter/water separator. See Fig. 1.
3) Rotate handle on drain valve forward, toward front of
vehicle to OPEN position. Drain valve is located near top of fuel
filter/water separator. See Fig. 1.
4) Allow water to drain until clean flow of diesel fuel
exists. Rotate handle on drain valve back to CLOSE position.
FUEL TRANSFER PUMP
NOTE: A defective fuel transfer pump may cause low power, hard
starting and White smoke. Check fuel transfer pump output
pressure (cranking and starting), pressure drop and fuel
supply.
Fuel Transfer Pump Preliminary Inspection
1) Check for restricted or leaking fuel supply line to fuel
transfer pump or fuel return line located on driver's side of engine.
See Fig. 1 . Repair fuel supply line or fuel return line if restricted
or leaking.
2) Check for fuel leaking from fuel transfer pump. Replace
fuel transfer pump if fuel is leaking. Check fuel transfer pump output
pressure.
Fuel Transfer Pump Output Pressure
1) Clean area around filter fitting plugs, then remove plugs.
See Fig. 7 . Install Test Fittings (AVU1-2). Install Fuel Pressure Test
Gauge (6828) at inlet port. See Fig. 7. To prevent engine starting,
remove fuel injection pump relay, located in power distribution
center.
2) Turn ignition switch to START position. Inlet pressure
should be 5-7 psi. Install fuel injection pump relay. Start engine.
Inlet pressure should be 10 psi. Using a scan tool, clear FTC. FTC may
set when relay is removed. Check pressure drop.
Fig. 7: Checking Fuel Transfer Pump Output Pressure
Courtesy of Chrysler Corp.
Pressure Drop Test
Turn engine off. Move pressure gauge from inlet port to

BO DY C O NTR O L C O M PU TE R

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Body Control Computer Tests
Ram Pickup
NOTE: See BODY CONTROL COMPUTER - INTRODUCTION article before
proceeding with following test. Body control computer in RWD
trucks is the Central Timer Module (CTM).
SYMPTOM IDENTIFICATION
IDENTIFYING VEHICLE EQUIPMENT & SYSTEM PROBLEMS
NOTE: For connector terminal identification wiring diagrams, see
BODY CONTROL COMPUTER - INTRODUCTION article.
NOTE: Perform a visual inspection before proceeding with this test.
Ensure battery is fully charged.
1) Connect scan tool to Data Link Connector (DLC). DLC is a
16-pin connector located under left side of dash, to left of steering
wheel. Turn ignition switch to ON position. If scan tool display is
not blank, go to next step. If scan tool display is blank, see
appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select SYSTEM MONITORS, then CCD BUS
TEST. Scan tool will perform a CCD bus test. If scan tool displays BUS
OPERATIONAL, go to next step. If scan tool displays any message except
BUS OPERATIONAL, see appropriate VEHICLE COMMUNICATIONS article.
3) Using scan tool, select READ DTCs. If any Diagnostic
Trouble Codes (fault messages) are present, go to appropriate fault
message. If no fault messages are present, identify customer
complaint. See following list for possible fault messages and customer
complaint symptoms. Problems listed are diagnosed using a scan tool.
These problems may occur separately or in various combinations. When
diagnosing a system with many apparent problems, a sequence of tests
may be required. After repairs, ensure problem(s) or failure(s) have\
been corrected.
CHIME SYSTEM
* CHIME INOPERATIVE - ENGINE TEMPERATURE CRITICAL
* CHIME INOPERATIVE - KEY IN IGNITION & LF DOOR OPEN
* CHIME INOPERATIVE AT ALL TIMES
* CHIME INOPERATIVE WITH EXTERIOR LIGHTS ON
* CHIME INOPERATIVE WITH LOW OIL PRESSURE
* CHIME INOPERATIVE WITH DRIVER DOOR OPEN
DOOR AJAR SYSTEM
* OPEN LEFT DOOR AJAR CIRCUIT
* OPEN RIGHT DOOR AJAR CIRCUIT
* SHORTED LEFT DOOR AJAR CIRCUIT
* SHORTED RIGHT DOOR AJAR CIRCUIT
INSTRUMENT CLUSTER
* ALL GAUGES INOPERATIVE
* ANY CCD CLUSTER WARNING LIGHT INOPERATIVE
* ANY HARD WIRED CLUSTER WARNING LIGHT INOPERATIVE

PCM INACTIVE ON BUS, go to appropriate VEHICLE COMMUNICATIONS article.
If scan tool does not display PCM INACTIVE ON BUS, go to next step.
4) Turn ignition off. Remove instrument cluster. See
appropriate INSTRUMENT PANELS article. Turn ignition on. Using
external voltmeter, measure voltage between ground and instrument
cluster connector C1 terminal No. 6 (Yellow wire). If voltage is 10
volts or less, repair open Yellow wire. If voltage is more than 10
volts, replace instrument cluster.
ANY CCD CLUSTER LIGHT INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Turn ignition on. Using scan tool, select ELECTRO/MECH
CLUSTER. If scan tool displays BUS OPERATIONAL, go to next step. If
scan tool does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article and follow appropriate symptom diagnostics.
2) If scan tool displays NO RESPONSE, go to appropriate
VEHICLE COMMUNICATIONS article. If scan tool does not display NO
RESPONSE, go to next step.
3) Using scan tool, select SYSTEM TEST. If scan tool displays
PCM INACTIVE ON BUS, go to appropriate VEHICLE COMMUNICATIONS article.
If scan tool does not display PCM INACTIVE ON BUS, go to next step.
4) Push and hold RESET button while cycling ignition key.
Release RESET button when CHEC appears in odometer display. Observe
inoperative light during self-test. If inoperative light did not
illuminate during self-test, go to next step. If inoperative light
illuminated during self-test, verify if light is controlled by an
input to instrument cluster. See appropriate wiring diagram in BODY
CONTROL COMPUTER - INTRODUCTION article. If light is controlled by an
input to instrument cluster, go to appropriate circuits article or
symptom test. See IDENTIFYING VEHICLE EQUIPMENT & SYSTEM PROBLEMS. If
light is not controlled by an input to instrument cluster, system is
currently functioning correctly.
5) Gain access to instrument cluster. See appropriate
INSTRUMENT PANELS article. If defective light is a LED, replace
instrument cluster. If defective light is a bulb, go to next step.
6) Remove and inspect defective bulb. If bulb is burned out,
replace bulb. If bulb is not burned out, replace instrument cluster.
ANY HARD WIRED CLUSTER WARNING LIGHT INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Remove instrument cluster. See appropriate INSTRUMENT
PANELS article. Remove inoperative bulb. If bulb is burned out,
replace bulb. If bulb is not burned out, go to next step.
2) Inspect wiring diagram and evaluate which instrument
cluster provides; power or ground for inoperative bulb. See
appropriate wiring diagram in BODY CONTROL COMPUTER - INTRODUCTION
article. Using external ohmmeter or voltmeter, check appropriate power
or ground circuit. If circuit is okay, replace instrument cluster. If
power or ground is not available at appropriate circuit, repair open

multiple engine sensors have failed, repair ground between splice and
PCM.
12) Connect jumper wire between OPS connector terminals. If
oil pressure warning indicator illuminates, replace OPS. If oil
pressure warning indicator does not illuminate, go to next step.
13) Do not remove jumper wire. Disconnect PCM Black connector
C2. PCM is located in engine compartment on right inner fender. Using
an external ohmmeter, measure resistance between ground and PCM White
connector C2 terminal No. 23 (Gray/Orange wire). If resistance is less\
than 5 ohms, replace PCM. If resistance is 5 ohms or more, repair open
Gray/Orange wire.
14) Check cooling system operation. If cooling system is
operating properly, go to next step. If cooling system is not
operating properly, repair engine cooling problem.
15) Using scan tool, select PCM MONITOR under SYSTEM TESTS.
If scan tool displays PCM ACTIVE ON BUS, system is currently
functioning properly. If scan tool does not display PCM ACTIVE ON BUS,
go to appropriate VEHICLE COMMUNICATIONS article.
16) Using scan tool, select MODULE ENGINE CONTROLLER. Read
PCM DTCs. If scan tool displays any charging system related DTCs, go
to appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section
and repair DTC as necessary. If scan tool does not display any
charging system related DTCs, go to next step.
17) Check charging system operation. If charging system is
operating properly, replace instrument cluster. If charging system is
not operating properly, repair engine charging problem.
18) Using scan tool, select BODY COMPUTER MONITORS. Read CCD
BUS ENGINE INFO. If scan tool displays engine RPM, replace instrument
cluster. If scan tool does not display engine RPM, replace PCM.
OVERHEAD CONSOLE CONCERNS
AVERAGE MPH/FUEL ECON INOPERATIVE OR WRONG (CMTC FAILS TO
RESPOND TO INSTRUMENT CLUSTER DIMMING, DISTANCE TO EMPTY
INOPERATIVE OR WRONG, ELAPSED TIME INOPERATIVE/WRONG, SWITCH
ON CMTC INOPERATIVE, TRIP ODOMETER INOPERATIVE/WRONG)
NOTE: If any listed symptoms exist, Compass Mini-Trip computer
(CMTC) is defective. Replace CMTC. Perform VERIFICATION TEST
VER- 1A after each repair.
CMTC SHOWS FAILED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
Using scan tool, perform AUTO SELF TEST. If CMTC shows
failed, replace CMTC. If CMTC does not show failed, system is
currently functioning properly.
CMTC SEGMENTS FAIL TO LIGHT UP
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
Using scan tool, perform AUTO SELF TEST. If CMTC segments
fail to illuminate, replace CMTC. If CMTC segments all illuminate
properly, system is currently functioning properly.
INCORRECT READING BEYOND +/- 5

1) Start engine, and check booster vacuum hose connections. A
hissing noise indicates a vacuum leak. Repair any vacuum leaks before
proceeding. Stop engine, and shift transmission into Neutral. Pump
brake pedal until all vacuum reserve in booster is depleted.
2) Hold brake pedal under light pressure. If pedal does not
hold firm and falls away, master cylinder may be faulty. Bleed system
using appropriate method, and repeat step 1). See BLEEDING PROCEDURES
under BLEEDING BRAKE SYSTEM.
3) If pedal still does not hold firm, master cylinder is
faulty. If pedal holds firm, start engine and observe pedal height. If
pedal height change is not apparent, power booster or vacuum check
valve is faulty. Install good check valve, and repeat steps 1) and 2).\
If pedal falls away slightly under light pressure and then holds firm,
go to next step .
4) Start engine. Release brake pedal. Increase engine speed
to 1500 RPM. Close throttle and immediately turn off ignition. Wait at
least 90 seconds, and try brake action again. Booster should provide 2
or more vacuum assisted pedal applications. If vacuum assist is not
provided, perform booster and check valve vacuum tests.
POWER BRAKE BOOSTER VACUUM TEST
Connect vacuum gauge to booster check valve using "T"
fitting. Start engine, and run at idle speed for one minute. Clamp
hose shut between vacuum source and check valve. Stop engine, and
observe vacuum gauge. If vacuum drops more than one in. Hg within 15
seconds, booster diaphragm or check valve is faulty.
POWER BRAKE BOOSTER CHECK VALVE TEST
Disconnect vacuum hose from check valve. Remove check valve
and valve seal from booster. Use a hand-operated vacuum pump for
testing. Apply 15-20 in. Hg at large end of check valve. Vacuum should
hold steady. If gauge on pump indicates vacuum loss, check valve is
faulty and should be replaced.
COMBINATION VALVE METERING VALVE TEST
Metering valve operation can be checked visually with aid of
an assistant. While an assistant applies and releases brake pedal,
observe metering valve stem. If valve is operating correctly, stem
will extend slightly when brakes are applied, and contract when brakes
are released. If valve is faulty, replace combination valve assembly.
COMBINATION VALVE PRESSURE DIFFERENTIAL SWITCH TEST
1) Using an assistant, apply brake pedal. Observe brake
warning light. Raise and support vehicle, and connect a bleed hose to
one rear wheel cylinder. Submerge other end of hose into container
partially filled with brake fluid. Have assistant press and hold brake
pedal down while observing brake warning light. Open bleeder screw. If
warning light glows, switch is operating properly.
2) If warning light fails to glow, check circuit fuse, bulb
and wiring. Repair as necessary. Repeat step 1). If warning light
fails to glow, check brakelight, parking brake switches and related
wiring. Repair as necessary. Repeat step 1). If warning light fails to
glow, pressure differential switch is faulty. Replace combination
valve assembly, and bleed brake system. Verify proper valve operation.
REMOVAL & INSTALLATION

pads at this time. On models with removable hub, install hub on rotor.
Install wheel and tire assembly. Tighten lug nuts so they are snug,
but DO NOT tighten to final torque specifications.
3) While rotating wheel, tighten adjuster nut sufficiently to
seat bearing. Loosen nut and retighten while still rotating wheel.
Back off adjuster nut to completely release bearing preload torque.
Ensure endplay of .001-.003" (.025-.076 mm). Install lock nut and NEW
cotter pin. If necessary, tighten lock nut slightly to align cotter
pin hole. Install grease cap. Tighten caliper bolts and lug nuts to
specification. See TORQUE SPECIFICATIONS table. To complete
installation, reverse remove procedure.
Removal (Ram Pickup With 8 Studs)
1) Raise and support vehicle. Remove wheel. Remove hub
extension, if equipped. Remove brake caliper. Support caliper aside.
2) On models with removable adapter hub, remove hub from
rotor. On models with one-piece hub and rotor assembly, remove cotter
pin from rotor hub nut. Remove nut. Disconnect ABS wheel speed sensor
wire (if equipped), and remove from frame and steering knuckle. Remove\
bolts securing hub to steering knuckle from inboard side of steering
knuckle. Remove rotor and hub assembly.
Installation
1) Apply anti-seize compound to drive shaft splines. Replace
grease seal in steering knuckle, if necessary. Insert 2 rearmost top
and bottom rotor hub bolts in steering knuckle so they extend through
back of knuckle. Install hub spacer, ensuring flat on space is
positioned to rear. Use chassis grease to hold spacer in position, if
necessary.
NOTE: If equipped with wheel speed sensor, brake shield must be
positioned on hub bearing, and sensor wire must be at top of
knuckle.
2) Align rotor hub with drive shaft and install hub assembly.
Align bolt holes in hub flange with bolts previously installed. Start
nuts on flange bolts sufficiently to hold assembly in place. Install
remaining bolts, and tighten all bolts to specification. See TORQUE
SPECIFICATIONS table.
3) Install washer and hub nut. Tighten nut securely. Install
NEW cotter pin. Install grease cap. Install caliper. Tighten caliper
bolts and lug nuts to specification. See TORQUE SPECIFICATIONS table.
To complete installation, reverse remove procedure.
REAR BRAKE SHOES
WARNING: Use water or brake cleaner to clean brake parts. DO NOT use
compressed air to remove dirt and dust.
Removal (Dakota & Ram Van)
1) Remove wheel and drum. Note how secondary spring overlaps
primary return spring. Using spring remover, remove brake shoe return
springs. Slide automatic adjuster cable off anchor. Disconnect cable
from adjusting lever.
2) Remove cable, cable guide and anchor plate. See Figs. 3,
4, and 5. Disconnect adjusting lever return spring from lever. Remove
lever and return spring from pivot pin. Remove shoe-to-shoe spring.
Spread shoes, and remove adjustment star wheel.
3) Remove shoe retainers, springs and pins. Remove parking
brake lever from secondary shoe. Remove shoes and parking brake strut
with spring.

being replaced, remove booster check valve and seal.
Installation
1) If new booster is being installed, install check valve and
seal. Position booster on dash, and install lock nuts on booster
mounting studs finger tight. Install booster push rod on brake pedal
pin, and secure rod with NEW retaining clip.
2) Tighten booster lock nuts to specification. Install master
cylinder on booster, and tighten mounting nuts to specification. See
TORQUE SPECIFICATIONS table. Connect vacuum hose to booster check
valve. Start vehicle and check booster operation.
COMBINATION VALVE
Removal & Installation
Raise and support vehicle. Mark brakelines for assembly
reference. Disconnect parking brake cable from clip on valve, if
necessary. Disconnect brake warning light connection at switch.
Disconnect all brake hydraulic lines at valve. Cap brakelines to
prevent dirt from entering system. Remove valve. To install, reverse
removal procedures. Bleed brake system. See BLEEDING PROCEDURES under
BLEEDING BRAKE SYSTEM.
AXLE BEARING & SEAL (FULL FLOATING AXLE)
Removal & Installation (Ram Pickup With 12" & 13" Drums)
1) Raise and support vehicle. Remove wheel. Remove axle shaft
nuts and washers. Strike center of axle flange to free cones. Remove
axle shaft and gasket.
2) Straighten and remove nut lock. Remove adjustment nut and
outer bearing. Remove drum assembly. Remove seal and inner bearing
from drum assembly.
3) Pack inner bearing, and install inner bearing and seal in
drum. Install drum assembly, outer bearing and adjustment nut. While
rotating drum, tighten adjustment nut to specification. See TORQUE
SPECIFICATIONS table.
4) Back off adjustment nut 1/8 turn to obtain .001-.010" (0.
025-0.254 mm) end play. Bend nut lock into spindle keyway. Install
gasket and axle shaft. Install wheel, and lower vehicle. See TORQUE
SPECIFICATIONS table.
OVERHAUL
NOTE: Use illustrations when overhauling components. See
Figs. 2-6.
DISC BRAKE SPECIFICATIONS
DISC BRAKE SPECIFICATIONS








\









\









\









\









\









\









\







Application In. (mm)\
Disc Diameter
Dakota ............................................... 11.30 (287)\
Ram Pickup
1/2 Ton ............................................. 11.57 (294)\
3/4 & 1 Ton ......................................... 12.50 (318)\
Ram Van
1/2 & 3/4 Ton ....................................... 11.75 (299)\
1 Ton ............................................... 12.82 (326)\
Lateral Runout

pointer is at one o'clock position. Push in on knob slightly and
continue rotating knob to its full clockwise stop. Place knob pointer
at a position about .32" (8 mm) beyond end of Red stripe. Release
knob. If knob is pointing at about .32" (8 mm) beyond end of Red
stripe, go to next step. If knob is not pointing at about .32" (8 mm)
beyond end of Red stripe, go back to step 2) and repeat adjustment
procedure.
4) Rotate temperature control knob counterclockwise so that
knob pointer is at 12 o'clock position. Push temperature control knob
straight into heater control panel until perimeter of knob (not knob
pointer) is flush with base of heater control panel.
5) Rotate temperature control knob to its full clockwise
stop. Release knob. Knob pointer should be aimed at end of Red stripe.
If knob is pointed at end of Red stripe, go to next step. If knob is
not pointed at end of Red stripe, go back to step 2) and repeat
adjustment procedure.
6) Rotate temperature control knob to its full
counterclockwise stop. Release knob. If knob springs back, self-
adjuster clip securing temperature control cable to blend-air door
lever is improperly installed. See TEMPERATURE CONTROL CABLE R & I
under REMOVAL & INSTALLATION. If knob does not springs back,
temperature control cable adjustment is complete.
TROUBLE SHOOTING
HEATER PERFORMANCE
Check cooling system. Check serpentine drive belt tension.
Check radiator and radiator fan operation. Ensure that accessory
vacuum supply line is connected at power brake booster (Dakota) or
engine vacuum source (except Dakota).
TESTING
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
BLOWER MOTOR RELAYS
1) Blower motor relay is located in Power Distribution Center
(PDC). On Ram Van/Wagon, high speed blower motor relay is located in
engine compartment (on side of heater assembly). On all models,
disconnect negative battery cable. Remove blower motor relay. Using an
ohmmeter, check for continuity between terminals No. 87A and 30 of
relay. See Fig. 1. If continuity does not exist, replace relay. If
continuity exists, go to next step.
2) Using an ohmmeter, check for continuity between terminals
No. 30 and 87 of relay. If continuity exists, replace relay. If
continuity does not exist, go to next step.
3) Measure resistance between terminals No. 85 and 86 of
relay. Reading should be 70-80 ohms. If reading is not as specified,
replace relay. If reading is as specified, go to next step.
4) Using jumper wires, connect battery voltage to terminal
No. 86 and ground terminal No. 85. See Fig. 1. Check that continuity
exists between terminals No. 30 and 87. Check that continuity does not
exist between terminals No. 87A and 30. If continuity is not as
specified, replace blower motor relay. If continuity is as specified,
relay is okay.

WIRING DIAGRAM COMPONENT LOCATIONS
When trying to locate a component in a wiring diagram and you
don't know the specific system where it is located, use this handy
component locator to find the system wiring diagram in which the
component is located. Then, go to that system and locate the component
within the wiring diagram.
For example, if you don't know the specific system in which
the ignition switch is located, look up ignition switch in the wiring
diagram component location tables and go to the appropriate wiring
diagram(s) which contain either full or partial views of the ignition
switch. The full view of the ignition switch is located in Power
Distribution.
The first listing for the component will be the full or most
complete view of the component. Additional listings will be partial
views of the component. Not all components are used on all models.
All components will have a partial view in Ground
Distribution and Power Distribution. Data Link Connectors show
connecting circuits between modules. Alternate names for components
may be listed in wiring diagram component locations tables.
WIRING DIAGRAM COMPONENT LOCATIONS TABLE









\









\









\









\









\









\









\







Component Wiring Diagram
ABS Electronic Control Unit ....................... Anti-Lock Brakes
Data Link Connectors
ABS Hydraulic Unit ................................ Anti-Lock Brakes
Acceleration Sensor ............................... Anti-Lock Brakes
Accessory Delay Relay ................................ Power Windows
A/C Compressor Clutch Relay ..................... Engine Performance
A/C Sensor ...................................... Engine Performance
A/C Pressure Switch ............................. Engine Performance
Adaptive Lamp Control Module ....................... Exterior Lights
Air Bag(s) ................................ Air Bag Restraint System\
Air Bag Module ............................ Air Bag Restraint System
Air Bag Sensor(s) ......................... Air Bag Restraint System\
Air Injection Pump Relay ........................ Engine Performance
Air Temperature Sensor ............................ Overhead Console
Alternator (Generator) ..................... Generators & Regulators\
Anti-Theft Control Module ........................ Anti-Theft System
Starters
Autolamp Control Relay ........................... Headlight Systems
Daytime Running Lights
Automatic Shutdown (ASD) Relay .................. Engine Performance\
Generators & Regulators
Autostick Switch ................................ Engine Performance
Auxiliary Battery Relay .................... Generators & Regulators
Back-Up Lights ...................................... Back-Up Lights
Exterior Lights
Barometric (BARO) Pressure Sensor ............... Engine Performance\
Battery ......................................... Power Distribution
Battery Temperature Sensor ...................... Engine Performance
Body Control Module .......................... Body Control Computer
Anti-Theft System
Daytime Running Lights
Engine Performance
Headlight Systems
Warning Systems
Boost Control Solenoid .......................... Engine Performance
Boost Sensor .................................... Engine Performance
Brake Fluid Level Switch .................. Analog Instrument Panels