Distributor DODGE RAM 1999 Service Owner's Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 648 of 1691
Fig. 13: Drive Belt Routing (5.9L - Heavy Duty Cycle)
Courtesy of Chrysler Corp.
OIL PAN
Removal (Dakota 2WD & Durango 2WD)
1) Disconnect negative battery cable. Remove oil dipstick and
distributor cap. Raise and support vehicle. Drain engine oil.
2) Remove exhaust pipe. Remove side engine mount bolts.
Slightly raise engine. When engine is at adequate height, install
bolts in side engine mount-to-frame bracket holes to support engine.
3) Lower engine, and allow it to rest on bolts installed in
side engine mounts. Remove oil pan bolts, oil pan and gaskets.
Installation
1) To install, reverse removal procedure. Before installing
oil pan, apply RTV sealant where front cover contacts cylinder block,
where oil pan side gaskets meet end seals, and where end seals contact
cylinder block. See Fig. 14.
2) To facilitate oil pan installation, fabricate 4 alignment
dowels from 1 1/2" x 5/16" bolts. See Fig. 15. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table. To install remaining
Page 658 of 1691
![DODGE RAM 1999 Service Owners Manual OIL PUMP SPECIFICATIONS \
\
\
\
\
\
\
Application](/img/12/56915/w960_56915-657.png "DODGE RAM 1999 Service Owners Manual OIL PUMP SPECIFICATIONS \
\
\
\
\
\
\
Application")
OIL PUMP SPECIFICATIONS \
\
\
\
\
\
\
Application Specification
Inner & Outer Rotor Thickness ................ .825" (20.96 mm) Min.\
Outer Rotor Diameter .......................... 2.47" (62.7 mm) Min.\
Outer Rotor-To-Pump Body Clearance ............. .014" (.36 mm) Max.\
Pump Cover Warpage ........................... .0015" (.038 mm) Max.\
Rotor End Clearance ................................. .004" (.10 mm)\
Rotor Tip Clearance ............................ .008" (.20 mm) Max.\
Spring Free Length ................................. 1.95" (49.5 mm)\
Spring Tension ......... 19.5-20.5 Lbs. @ 1.34" (8.8-9.3 kg @ 34 mm)\
\
\
\
\
\
\
\
CAUTION: Ensure oil pump fully engages with distributor drive shaft
before tightening bolt. It may be necessary to slightly
rotate oil pump during installation to align with distributor
drive shaft.
Reassembly & Installation
To reassemble, reverse disassembly procedure. Install NEW
relief valve retainer cap and oil seal ring. Tighten pump cover bolts.
Fill rotor cavity with engine oil before installing. To install,
reverse removal procedure.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Axle Bracket-To-Bellhousing Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Axle Shaft Nut
Dakota 4WD & Durango 4WD ............................... 180 (244)\
Axle Shaft-To-Differential Flange Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Axle-To-Insulator Bolt
Dakota 4WD & Durango 4WD ................................ 75 (102)\
Camshaft Sprocket Bolt ..................................... 50 (68)\
Camshaft Thrust Plate Bolt ................................. 18 (24)\
Clutch Housing-To-Cylinder Block Bolt
Dakota
(1) ..................................................... 30 (41)
( 2) ..................................................... 50 (68)
Ram Pickup
( 1)
3/8" Bolt ............................................ 33 (45)\
7/16" Bolt ........................................... 50 (68)\
( 2) ........................................................ N/A
Connecting Rod Bolt ........................................ 45 (61)\
Crankshaft Pulley Bolt ..................................... 18 (24)\
Cylinder Head Bolt ( 3)
Step 1 ................................................... 50 (68)\
Step 2 ................................................. 105 (142)\
Step 3 (Verify Torque) ................................. 105 (142\
)
Differential Pinion Nose Bracket-To-Adapter Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Differential Pinion Nose Bracket-To-Bellhousing Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Engine Mount Bracket-To-Frame Rail Bolt
Dakota 2WD & Durango 2WD ................................. 30 (41)\
Page 705 of 1691
CLUTCH PEDAL POSITION SWITCHES
COLD START INJECTORS
CONNECTORS
COOLANT
COOLANT RECOVERY TANKS
COOLING FAN MOTOR MODULES
COOLING FAN MOTOR RELAYS AND MODULES
COOLING FAN MOTOR RESISTORS
COOLING FAN MOTOR SENSORS AND SWITCHES
COOLING FAN MOTOR SWITCHES
COOLING FAN MOTORS
CRANKSHAFT POSITION SENSORS
DECEL VALVES
DEFLECTORS
DIP STICKS AND TUBES
DIP STICK TUBES
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR CAPS
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ROTORS
DISTRIBUTOR SHIELDS
DISTRIBUTORS
EARLY FUEL EVAPORATION VALVES (HEAT RISER ASSEMBLIES)
EGR COOLERS
EGR EXHAUST MANIFOLD PASSAGES
EGR INTAKE AND EXHAUST MANIFOLD PASSAGES
EGR PLATES AND COOLERS
ELECTRONIC SPARK CONTROL MODULES
ELECTRONIC TRANSMISSION CONTROL DEVICES
ELECTRONIC TRANSMISSION FEEDBACK DEVICES
ENGINE COOLANT TEMPERATURE SENSORS
ENGINE COOLING SYSTEMS
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE OIL
ENGINE OIL CANISTERS
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL GASKETS
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER PURGE DEVICES
EVAPORATIVE EMISSION (EVAP) CANISTERS
EVAPORATIVE EMISSION (EVAP) FEEDBACK DEVICES
EXHAUST GAS RECIRCULATION DEVICES
EXHAUST GAS RECIRCULATION FEEDBACK DEVICES
EXPANSION PLUGS
FAN CONTROL SENSORS
FUEL
FUEL ACCUMULATORS AND DAMPERS
FUEL AND COLD START INJECTORS
FUEL DAMPERS
FUEL DELIVERY CHECK VALVES
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL FILLER NECKS AND RESTRICTORS
FUEL FILTERS
FUEL INJECTORS
FUEL LEVEL SENDERS7
FUEL PRESSURE REGULATORS
FUEL PUMPS (IN-TANK AND EXTERNAL, ELECTRICAL OR MECHANICAL)
FUEL RAILS
FUEL RESTRICTORS
Page 737 of 1691
![DODGE RAM 1999 Service Owners Manual \
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TU](/img/12/56915/w960_56915-736.png "DODGE RAM 1999 Service Owners Manual \
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TU")
\
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TUBES .
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ADVANCE AND RETARDER (MECHANICAL AND VACUUM) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A .. Require repair or replacement.
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A ............ Require replacement.
Out of specification .... B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR BOOT AND SHIELD INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Deteriorated ............ A ............ Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. A ............ Require replacement.
Torn .................... A ............ Require replacement.
\
\
\
\
\
\
\
DISTRIBUTOR CAPS
DISTRIBUTOR CAP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 738 of 1691
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Burned .................. A ............ Require replacement.
Carbon button missing ... A ............ Require replacement.
Carbon button worn,
affecting performance .. A ............ Require replacement.
Carbon button worn, not
affecting performance .. 1 ............ Suggest replacement.
Carbon-tracked .......... A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Loose ................... 2 .. Suggest repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal eroded, affecting
performance ............ A .. Require repair or replacement.
Terminal eroded, not
affecting performance .. .. ........ No service suggested or
required.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
See
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM) .
DISTRIBUTOR ROTORS
DISTRIBUTOR ROTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Carbon-tracked .......... A ............ Require replacement.
Contact burned .......... A ............ Require replacement.
Corroded ................ 1 ............ Suggest replacement.
Page 739 of 1691
Eroded .................. 1 ............ Suggest replacement.
Loose ................... A .. Require repair or replacement.
Out of specification .... B ............ Require replacement.
\
\
\
\
\
\
\
DISTRIBUTOR SHIELDS
See DISTRIBUTOR BOOTS AND SHIELDS .
DISTRIBUTORS
DISTRIBUTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bushings worn, affecting
performance ............ A .. Require repair or replacement.
Bushings worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Cam lobes worn, affecting
performance ............ A .. Require repair or replacement.
Cam lobes worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Gear broken ............. A .. Require repair or replacement.
Gear worn, affecting
performance ............ A ............ Require replacement.
Gear worn, not affecting
performance ............ .. ........ No service suggested or
required.
Integrated pickup
triggering device
loose .................. A .. Require repair or replacement.
Integrated pickup
triggering device
magnetism incorrect .... A .. Require repair or replacement.
Leaking oil internally .. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Pickup triggering device
(reluctor) broken ...... A .. Require repair or replacement.
Pickup triggering device
(reluctor) loose ....... A .. Require repair or replacement.
Pickup triggering device
(reluctor) weak ........ A .. Require repair or replacement.
Reluctor (pickup
triggering device)
broken ................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
loose .................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
weak ................... A .. Require repair or replacement.
Shaft bent .............. A ............ Require replacement.
Thrust washer broken .... A .. Require repair or replacement.
Page 755 of 1691
Flow restricted ......... B .. Require repair or replacement.
Inoperative ............. B ........... (2) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Resistance out of
specification .......... B ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation, out of
OEM specification. Some components may be serviceable.
\
\
\
\
\
\
\
FUEL DAMPERS
See FUEL ACCUMULATORS AND DAMPERS .
FUEL DELIVERY CHECK VALVES
FUEL DELIVERY CHECK VALVE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Inoperative ............. A ........ ( 1) Require replacement.
Leaking externally ...... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Pressure leaking (bleeds
down) .................. A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of OEM
specification.
\
\
\
\
\
\
\
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL DISTRIBUTOR (BOSCH CIS) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Inoperative ............. A ........... ( 1) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Out of specification .... B .. Require repair or replacement.
Restricted, affecting
Page 850 of 1691
![DODGE RAM 1999 Service Owners Manual Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Int](/img/12/56915/w960_56915-849.png "DODGE RAM 1999 Service Owners Manual Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Int")
Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Interlock Systems
Buzzer Module ...................................... Warning Systems
Camshaft Position (CMP) Sensor .................. Engine Performance\
Central Control Module ........................... Anti-Theft System
Clockspring ............................... Air Bag Restraint System
Cruise Control Systems
Steering Column Switches
Clutch Pedal Position Switch .............................. Starters
Clutch Start Switch ....................................... Starters
Combination Meter ......................... Analog Instrument Panels
Constant Control Relay Module (CCRM) ............ Engine Performance\
Electric Cooling Fans
Convenience Center .............................. Power Distribution
Illumination/Interior Lights
Convertible Top Motor ........................ Power Convertible Top
Convertible Top Switch ....................... Power Convertible Top
Crankshaft Position (CKP) Sensor ................ Engine Performance\
Cruise Control Module ....................... Cruise Control Systems
Cruise Control Switch ....................... Cruise Control Systems
Condenser Fan Relay(s) ....................... Electric Cooling Fans\
Data Link Connector (DLC) ....................... Engine Performance\
Daytime Running Lights Module ............... Daytime Running Lights
Exterior Lights
Defogger Relay ................................ Rear Window Defogger
Diagnostic Energy Reserve Module (DERM) ... Air Bag Restraint System\
Discriminating Sensor (Air Bag) ........... Air Bag Restraint System\
Distributor ..................................... Engine Performance
Door Lock Actuators ............................... Power Door Locks
Remote Keyless Entry
Door Lock Relay(s) ................................ Power Door Locks\
Electrochromic Mirror ................................ Power Mirrors
Electronic Level Control (ELC)
Height Sensor .............................. Electronic Suspension
Electronic Level Control (ELC) Module ........ Electronic Suspension\
Engine Coolant Temperature (ECT)
Sending Unit ............................ Analog Instrument Panels
Engine Coolant Temperature (ECT) Sensor ......... Engine Performance\
Engine Control Module ........................... Engine Performance
Generators & Regulators
Starters
ETACS ECU .......................................... Warning Systems
Power Windows
Remote Keyless Entry
Evaporative (EVAP) Emissions Canister ........... Engine Performance\
EVAP Canister Purge Solenoid .................... Engine Performance
EVAP Canister Vent Solenoid ..................... Engine Performance
Exhaust Gas Recirculation (EGR) Valve ........... Engine Performance\
Fuel Tank Vacuum Sensor ......................... Engine Performance
Fog Lights ....................................... Headlight Systems
Daytime Running Lights
Fog Light Relay .................................. Headlight Systems
Daytime Running Lights
Fuel Door Release Solenoid ................. Power Fuel Door Release
Fuel Gauge Sending Unit ................... Analog Instrument Panels
Fuel Injectors .................................. Engine Performance
Fuel Pump ....................................... Engine Performance
Fuel Pump Relay ................................. Engine Performance
Power Distribution
Fuse/Relay Block ................................ Power Distribution
Fusible Links ................................... Power Distribution
Generators & Regulators
Page 951 of 1691
NOTE: Oil pressure sensor may also be referred to as engine oil
pressure sensor.
Removal & Installation
For oil pressure sensor location, see OIL PRESSURE SENSOR
LOCATION table. Service information is not available from
manufacturer.
OIL PRESSURE SENSOR LOCATION
\
\
\
\
\
\
\
Application Location
Dakota
2.5L ... ( 1) Passenger's Side Of Cylinder Block, Below Distributor
3.9L, 5.2L & 5.9L ... ( 1) Passenger's Side Rear Corner Of Cylinder
Block, Below Distributor
Durango .. ( 1) Passenger's Side Rear Corner Of Cylinder Block, Below
Distributor
Ram Pickup
3.9L, 5.2L & 5.9L ... ( 2) Passenger's Side Rear Corner Of Cylinder
Block, Below Distributor
8.0L ......................................... ( 2) Near Oil Filter
Ram Van & Ram Wagon ... ( 3) Passenger's Side Rear Corner Of Cylinder
Block, Below Distributor
( 1) - Contains a Gray/Yellow wire and a Black/Light Blue wire in the
electrical connector.
( 2) - Contains a Gray/Orange wire and a Black/Light Blue wire in the
electrical connector.
( 3) - Contains a Gray wire and a Black/Light Blue wire in the
electrical connector.
\
\
\
\
\
\
\
OUTPUT SHAFT SPEED SENSOR
NOTE: Output shaft speed sensor may also be referred to as
transmission speed sensor.
Removal & Installation (A/T Models)
Output shaft speed sensor is located on lower edge of
overdrive case on rear of transmission. See Fig. 10. Disconnect
electrical connector at output shaft speed sensor. Remove output shaft
speed sensor with "O" ring from transmission. To install, reverse
removal procedure using NEW "O" ring.
Fig. 10: Locating Output Shaft Speed Sensor & Park/Neutral Switch
(A/T)
Courtesy of Chrysler Corp.
PARK/NEUTRAL SWITCH
Page 956 of 1691
![DODGE RAM 1999 Service Owners Manual POWER DISTRIBUTION CENTER (PDC) LOCATION \
\
\
\
\
\
\
Applic](/img/12/56915/w960_56915-955.png "DODGE RAM 1999 Service Owners Manual POWER DISTRIBUTION CENTER (PDC) LOCATION \
\
\
\
\
\
\
Applic")
POWER DISTRIBUTION CENTER (PDC) LOCATION \
\
\
\
\
\
\
Application Location
Dakota & Durango .............. Driver's Side Of Engine Compartment,
Behind Battery
Ram Pickup .................... Driver's Side Of Engine Compartment,
Above Wheelwell
Ram Van & Ram Wagon ........... Driver's Side Of Engine Compartment,
Near Battery
\
\
\
\
\
\
\
STARTER RELAY & TRANSMISSION RELAY
NOTE: Transmission relay may also be referred to as transmission
control relay.
Removal & Installation
Relay is located in Power Distribution Center (PDC). Relays
may be identified by label on inside of PDC cover. See POWER
DISTRIBUTION CENTER (PDC) LOCATION table.
EVAP PURGE SOLENOID
NOTE: EVAP purge solenoid may also be referred to as EVAP canister
purge solenoid, duty cycle solenoid or proportional purge
solenoid.
Removal & Installation
See EVAP PURGE SOLENOID under EMISSION SYSTEMS.
TRANSMISSION GOVERNOR PRESSURE SOLENOID
NOTE: Transmission governor pressure solenoid may also be referred
to as governor pressure solenoid.
Removal & Installation (A/T Models)
Transmission governor pressure solenoid is located on
transmission valve body. See appropriate ELECTRONIC CONTROLS article
in AUTOMATIC TRANSMISSIONS section.
TRANSMISSION OVERDRIVE SOLENOID & TRANSMISSION TORQUE
CONVERTER CLUTCH (TCC) SOLENOID
NOTE: Transmission overdrive solenoid may also be referred to as
overdrive solenoid or 3-4 shift solenoid.
Removal & Installation (A/T Models)
Transmission overdrive solenoid and TCC solenoid are located
in solenoid assembly on transmission valve body. See appropriate
ELECTRONIC CONTROLS article in AUTOMATIC TRANSMISSIONS section.
IGNITION SYSTEM
CAMSHAFT POSITION SENSOR
Removal & Installation (Dakota, Durango, Ram Pickup 3.9L,
5.2L & 5.9L, Ram Van & Ram Wagon)
1) Camshaft position sensor is located in the distributor.
See Fig. 13 . Camshaft position sensor may be serviced without removing