mirror DODGE RAM 1999 Service Owner's Manual

Power Mirror Circuit
POWER SEATS

Ram Van & Ram Wagon
1) Place window glass halfway between up and down positions.
Verify glass can be moved slightly from side to side, front to rear,
and up and down. If glass does not move freely, check window glass,
tracks and regulator for sticking or binding. Repair as necessary and
recheck system operation. If glass moves freely, go to next step.
2) Disconnect negative battery cable. Disconnect and remove
power window switch in door with inoperative window. See POWER WINDOW
SWITCH under REMOVAL & INSTALLATION. Connect negative battery cable.
Turn ignition on. Measure voltage between passenger power window
switch wiring harness connector terminal (Tan wire) or driver power
window switch wiring harness connector terminal (Tan wire) and ground.\
See WIRING DIAGRAMS. If battery voltage is not present, repair open
Tan wire as necessary. If battery voltage exists, and inoperative
window is on driver side, go to step 4). If battery voltage exists,
and inoperative window is on passenger side, go to next step.
NOTE: Passenger's power window switch is grounded through driver's
power window switch.
3) Disconnect negative battery cable. Check continuity
between ground and passenger's power window switch harness connector
terminals No. 2 (Brown/White wire) and No. 4 (Violet/White wire). Se\
e
WIRING DIAGRAMS. If continuity exists on both circuits, go to step 5).
If continuity does not exist on either or both circuits, repair open
circuit.
4) Check power window switch. See POWER WINDOW SWITCH under
COMPONENT TESTS. Replace faulty power window switch as necessary. If
switch is okay, go to next step.
5) Using an ohmmeter, check continuity of each circuit
between inoperative power window switch wiring harness connector and
corresponding power window motor wiring harness connector terminal.
See WIRING DIAGRAMS. If continuity does not exist in one or more
circuits, repair open circuit(s) as necessary. Recheck system
operation. If continuity exists in all circuits, power window switch
and switch circuits are okay. Check power window motor. See POWER
WINDOW MOTOR under COMPONENT TESTS.
REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
DOOR TRIM PANEL
Removal & Installation (Caravan, Town & Country, & Voyager)
1) Using a trim stick, pry courtesy light from door trim.
Disconnect courtesy light connector. Remove door assist handle (if
equipped). Remove door pull cup (if equipped). Remove screws attachin\
g
trim panel to door below map pocket (if equipped). Using a trim stick,\
remove screw cover from switch panel.
2) Remove screws securing switch panel to door trim and
remove panel. Using a trim stick, remove seat/mirror memory switch (if
equipped). Remove screw securing door trim to door panel from behind
inside latch release handle.
3) Disengage clips holding door trim to door frame around
perimeter of panel. Tilt top of trim panel away from door to gain
access to latch linkage. Disengage clip holding linkage rod to inside
latch release handle. Separate linkage rod from latch handle. Remove

removal procedure.
Removal & Installation (Ram Van & Ram Wagon)
Disconnect negative battery cable. Remove door trim panel.
See DOOR TRIM PANEL. Remove mirror flag bezel. Remove screws attaching
window switch mounting plate to mirror flag bezel. Using a thin
screwdriver, gently pry snap clips at sides of window switch
receptacle from rear of mounting plate. Pull switch out of receptacle.
To install, reverse removal procedure. Tighten mounting screws to 20
INCH lbs. (2.2 N.m).
Removal & Installation (Dakota & Ram Pickup)
Disconnect negative battery cable. Using a trim stick, gently
pry upper edge of switch bezel to release retainer securing bezel to
door trim panel. Pull switch and bezel away from door trim panel and
disconnect switch wire connector. To install, reverse removal
procedure.
Removal & Installation (Durango)
Disconnect negative battery cable. Remove door trim panel.
See DOOR TRIM PANEL. On driver's door, remove screws from back side of
door trim panel and remove switch and bezel. On passenger's doors,
gently pry snap clips at sides of window switch receptacle on back of
door trim panel switch bezel. On all doors, remove power window switch
from bezel. To install, reverse removal procedure.
WIRING DIAGRAMS