Heater mode actuator DODGE RAM 1999 Service Repair Manual

BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument


* A /C -H EA TE R S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
A/C-Heater System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Heating, Ventilation and Air Conditioning
ACCUMULATORS
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AIR CONDITIONING FITTINGS
AIR CONDITIONING HOSES
AIR CONDITIONING METAL LINES, HOSES AND FITTING ASSEMBLIES
AIR CONTROL DOORS
AIR DAMS (EXTERNAL)
AIR DISTRIBUTION SYSTEM
BELTS
BLEND DOORS
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER MOTORS
BLOWER RESISTORS
BLOWER SWITCHES
CABIN AIR FILTERS
CIRCUIT BREAKERS
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSORS
CONDENSER AIR SEALS
CONDENSER FAN MOTORS
CONDENSERS
CONNECTORS
CONTROL CABLES
CONTROL HEADS (FUNCTION SELECTORS)
CONTROL LINKAGES
CONTROL MODULES
COOLANT
COOLING FAN BLADES
COOLING FAN CLUTCHES
COOLING FAN MOTORS
EVAPORATOR DRAIN TUBES
EVAPORATOR PRESSURE REGULATORS (EPRS)
EVAPORATORS
EXPANSION VALVES
FUNCTION SELECTORS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GASKETS
HEATER CASES
HEATER CONTROL VALVES
HEATER CORES

OPERATION
CONTROL PANEL
Blower Motor Switch
Fan speed is controlled with a rotary switch. On front A/C-
heater systems, there are 4 different fan speed settings. Low, medium-
low, medium-high, and high. On rear A/C-heater systems, there are 3
different fan speed settings. Low, medium, and high.
Mode Control Knob
Mode rotary switch is used to change direction of air flow.
There are 7 different modes of operation: recirculation, panel with
A/C, floor/panel, panel without A/C (vent), floor, floor/defrost, and
defrost.
Temperature Control Knob
Temperature rotary switch controls temperature blend/air door
position by a cable on Dakota and Durango, and by vacuum actuator for
Ram Pickup. When cold temperature is selected, no air flows across
heater core. When hot temperature is selected, all air flows through
heater core. Temperature may vary by any setting between cold and hot.
CLUTCH CYCLING PRESSURE SWITCH
Dakota & Ram Pickup
Clutch cycling low pressure switch is mounted on a Schrader-
type valve fitting that is part of the accumulator. It is connected in
series with the high pressure cut-off switch and control panel,
between ground and PCM. Switch contacts open and close due to changes
in A/C system pressure. Opening and closing of switches will cause PCM
to turn compressor clutch on and off, regulating system pressure which
controls temperature of evaporator.
Clutch cycling low pressure switch contacts are normally open
when suction (low side) pressure drops below 25 psi (1.8 kg/cm
) on
Ram Pickup; 20.5 psi (1.4 kg/cm) on Dakota. Extreme cold weather will
also open contacts. When contacts are open, PCM will de-energize
compressor clutch relay, disengaging compressor clutch.
Clutch cycling pressure switch contacts will close when
suction (low side) pressure rises above 43 psi (3.0 kg/cm
) on Ram
Pickup or 36 psi (2.5 kg/cm) on Dakota. When contacts are closed, PCM
will energize compressor clutch relay, engaging compressor clutch.
ELECTRONIC CYCLING CLUTCH SWITCH
Durango
The electronic cycling clutch switch is mounted to Thermal
Expansion Valve (TXV), also referred to as an "H" valve, in engine
compartment. It provides evaporator temperature to the PCM. Using this
information, the PCM will cycle the compressor clutch to prevent
evaporator icing. The switch is used for the front evaporator only.
Electronic cycling clutch switch is connected in series with
mode control switch, high pressure cut-out switch, low pressure cut-
out switch, and PCM. The electronic cycling clutch switch opens when
refrigerant temperature is below about 37
F (2.8C) and will close
when refrigerant temperature is about 40F (4.4C).
FIXED ORIFICE TUBE
Dakota & Ram Pickup
The fixed orifice tube is located in outlet line of the
condenser. The orifice tube inlet and outlet ends have a screen to

BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument


* E LE C TR IC AL S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Electrical System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
ACTUATOR MOTORS (SOLENOIDS) (ELECTRIC)
ACTUATOR MOTORS (VACUUM)
AIR BAGS
ALTERNATORS AND GENERATORS
AMPLIFIERS
ANTENNAS
BATTERIES
BATTERY CABLES
BATTERY CABLES
BATTERY HOLD DOWN HARDWARE
BATTERY TRAYS AND HOLD DOWN HARDWARE
BATTERY WIRES
BELTS
BULB SOCKETS
BULBS, SEALED BEAMS AND LEDS
CD PLAYERS
CIGARETTE LIGHTER ASSEMBLIES
CIRCUIT BREAKERS
CLUTCH SWITCHES
CONNECTORS
CONTROL MODULES
CRUISE CONTROL BRAKE SWITCHES
CRUISE CONTROL CABLES
CRUISE CONTROL CLUTCH SWITCHES
CRUISE CONTROL LINKAGES AND CABLES
CRUISE CONTROL RESERVOIRS
CRUISE CONTROL TUBES
CRUISE CONTROL VACUUM DUMP RELEASE VALVES
CRUISE CONTROL VACUUM HOSES, TUBES AND RESERVOIRS
CRUISE CONTROL VEHICLE SPEED SENSORS
DEFOGGERS
DEFROSTERS
DELAYS
DIMMERS
ELECTRIC HEATERS
EQUALIZERS
FUSE BLOCKS
FUSE BOXES AND BLOCKS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GAUGES
GENERATORS
GROUND CABLES AND STRAPS
GROUND STRAPS
HEADLIGHT ADJUSTERS
HEATING ELEMENTS (DEFROSTERS, DEFOGGERS, ELECTRIC HEATERS AND SEATS)
HORNS AND SIRENS

removal procedure.
HEATER ASSEMBLY
Removal (Dakota & Durango)
1) Disconnect negative battery cable. Drain cooling system.
Remove instrument panel. See INSTRUMENT PANEL.
2) In engine compartment, disconnect heater hoses and plug
all openings. Remove 4 heater assembly nuts from engine compartment
firewall. Inside vehicle, remove heater assembly support brace screw,
and swing support brace out of way. Move passenger seat rearward.
3) Carefully pull heater assembly rearward until studs and
heater core tubes clear firewall. Lower heater assembly and rotate
assembly until studs are facing downward. Remove heater assembly from
vehicle.
4) Place heater assembly on work bench with assembly housing
cover facing down. Remove 2 bolts securing heater assembly housing
cover to blower motor housing cover. Unplug vacuum harness connector
from panel/defrost door actuator.
5) Remove floor duct from heater assembly housing. Remove 2
bolts securing heater assembly housing cover to lower housing near
floor outlet. Turn assembly over. Disengage vacuum harness retainer
and vacuum harness. Remove 13 screws securing housing cover.
6) Remove blend-air door lever. Gently pry panel-defrost door
lever off. Pull up on heater assembly housing cover far enough to
separate cover sealant and remove cover.
Installation
Ensure blower motor housing cover sealant is in place and in
good condition. To complete installation, reverse removal procedure.
Removal (Ram Pickup)
1) Disconnect negative battery cable. Drain cooling system.
In engine compartment, remove coolant hoses from heater core tubes.
Plug all openings. Remove coolant overflow bottle. Remove instrument
panel. See INSTRUMENT PANEL . Remove Powertrain Control Module (PCM)
and position aside. DO NOT disconnect 60-pin connector from PCM.
2) Remove attaching nuts from studs on engine compartment
side of dash panel. Remove defrost duct. Disconnect electrical
connectors. Remove attaching nuts from studs in passenger compartment
side of dash panel. Remove heater assembly from vehicle.
3) Place heater assembly upside-down on work bench. Remove
screw securing floor duct to bottom of heater assembly and slide floor
duct off of center heat duct adapter. Unsnap center heat duct adapter
from bottom of heater assembly housing. Remove screw hidden behind
adapter. Remove remaining screws and separate heater assembly.
Installation
Ensure mode door pivot pins are properly inserted in holes.
To complete installation, reverse removal procedure.
Removal & Installation (Ram Van/Wagon)
1) Disconnect negative battery cable. Drain engine cooling
system. In engine compartment, protect generator from coolant
spillage. Remove heater hoses from heater core tubes. Plug all
openings. Remove grille, cowl grille support panel, right headlight
assembly, and right radiator core support assembly. See Fig. 7.
2) From inside vehicle, remove glove box bin. Through glove
box opening and from under instrument panel, remove nuts and bolts
attaching heater assembly to dash panel.
3) Remove blower housing flange screws. Separate heater
assembly from blower housing. See Fig. 6. Carefully remove heater
assembly from vehicle.