check engine DODGE RAM 2001 Service Repair Manual

UNDER VEHICLE
INSPECTION - TIRE PRESSURES
(1) Using the tire placard or the Safety Certifica-
tion Label, check that the correct tires are mounted
on the vehicle.
(2) Install valve stem extensions as required.
(3) Using the tire placard or the Safety Certifica-
tion Label, check tire pressure (including spare) and
adjust as required to recommended pressure.
(4) Inspect the spare tire for correct pressure and
proper mounting (Fig. 13).
NOTE: Tire pressure may have been set above nor-
mal during manufacturing in order to properly seat
the tire bead. Be sure to adjust to proper specifica-
tion.
INSPECTION - VISUAL
CAUTION: Before raising the vehicle on a hoist,
(Refer to LUBRICATION & MAINTENANCE/HOISTING
- STANDARD PROCEDURE) for the proper lifting
points.
(1) Visually inspect the following for loose attach-
ment, leakage, clearance and routing, and tighten
connections and clamps as required:
²Engine
²Oil Cooler
²Cooling System
²Transmission
²Driveshaft Boots²Differential
²Transfer Case (Fig. 19)
²Transmission Cooler and Lines (Fig. 18)
²Brake System and Lines (Fig. 14)
²Fuel System
²Exhaust System (Fig. 15), (Fig. 16) and (Fig. 17)
²Steering and Suspension Components
Fig. 13 SPARE TIRE INSPECTION
Fig. 14 BRAKE LINES TO CALIPERS (REAR)
Fig. 15 EXHAUST CLAMPS
30 - 8 NEW VEHICLE PREPARATIONBR/BE

ROAD TEST
DESCRIPTION - ROAD TEST INSPECTION
The following items must be inspected during the
road test portion of the new vehicle inspection.
²Check neutral safety switch operation
²Check operation of shift/clutch interlock system
²Check operation of gauges and warning lights
²Check horn operation
²Check operation of turn signals and emergency
flashers
²Check all mirror adjustments, including day/
night function
²Check windshield wipers for proper wipe pattern
and intermittent mode (if equipped)
²Check washer spray pattern
²Check heater, defroster and air conditioning for
proper operation
²Check that the fan operates quietly
²Check the rear window defroster (if equipped)
²Leave air selection lever in the fresh air position
²Check the rear heater and air conditioning for
proper operation
²Check the rear air register locations
²Check that the indicator lamps operate properly
²Check the operation of the radio, cassette and/or
compact disc player, and that sound quality is good
²Ensure that the clock displays the correct time
²Check that the trip computer/maintenance
reminder operates in all modes
²Check all speed control functions
²Check the service brakes to ensure that they
stop the vehicle in a straight line, without noise,
shudder or vibration
²Check the brake warning light
²Check the parking brake operation
²Check the engine's performance
²Check the transmission's performance for
smooth, quiet operation. If the vehicle is a 4x4, check
that the transfer case shifts easily among all ranges
²Check Autostick function (if equipped)
²Check the vehicle's steering and handling
²The steering wheel should be centered when
traveling in a straight line
²The vehicle should not pull or vibrate
²Check for squeaks, rattles and wind noise
²Check any other vehicle aspects you believe are
important, but that may not be included on the New
Vehicle Preparation Form
²Fill fuel tank with specified grade of fuel
INSPECTION - FUEL
Fill fuel tank with specified grade of gasoline (reg-
ular, midgrade or premium).
INSPECTION - OTHER
As part of DaimlerChrysler's Customer One philos-
ophy, the ªOtherº blank is provided on the New Vehi-
cle Preparation Form. This is designed to encourage
you to check any aspects of vehicle operation that
you believe are important to your customers, but that
do not appear elsewhere on the form.
INSPECTION - SQUEAKS, RATTLES AND WIND
NOISE
(1) Make sure that the instrument panel, glove
box, seats, steering wheel and column are free from
squeaks and rattles. Tighten any obvious loose fas-
teners.
(2) Check that the windows and doors are free
from squeaks, rattles and wind noise.
(3) Check that the vehicle exterior is free from
squeaks, rattles and noise, front and rear.
(4) Make sure that all interior panels are free from
squeaks and rattles.
INSPECTION - STEERING AND HANDLING
(1) Check that the power assist works properly (if
equipped). Steering should not require excessive
effort.
(2) Make sure the steering wheel does not vibrate
at idle or road speed.
(3) Ensure that the steering wheel is centered
when traveling straight ahead.
(4) Check that the vehicle does not drift to one
side.
(5) Make sure that the vehicle does not vibrate/
shake.
INSPECTION - TRANSMISSION/TRANSFER
CASE
AUTOMATIC TRANSMISSION
(1) Make sure that the park lock holds the vehicle
With the vehicle on a grade, put automatic trans-
mission in PARK and slowly release the service
brake to see if park lock holds. If it does not hold, the
transmission requires further service.
(2) Make sure shift lever operates easily/ smoothly
(Fig. 36).
Check for smooth shifting. Check for proper
upshifting and downshifting.
MANUAL TRANSMISSION
(1) Check that the shifter operates easily (Fig. 38).
(2) Make sure that the clutch operates smoothly
(Fig. 37).
(3) Look for proper synchronization.
The gears should not grind.
BR/BENEW VEHICLE PREPARATION 30 - 15

4X4 TRANSFER CASE
(1) Shift the transfer case through all ranges to
make sure shifting is smooth and all gear positions
respond accordingly (Fig. 39).
INSPECTION - ENGINE PERFORMANCE
Check the engine for proper performance. It
should:²Start promptly
²Be free from stalling
²Idle smoothly and at proper speed
²Be free from stumbling or hesitation
²Produce sufficient power
²Be free from unusual noises
²Operate within the proper temperature range
²Stop when the ignition key is shut off
Fig. 36 AUTOMATIC TRANSMISSION RANGE
SELECTOR
Fig. 37 CLUTCH PEDAL OPERATION
Fig. 38 MANUAL TRANSMISSION RANGE
SELECTOR
Fig. 39 TRANSFER CASE SELECTOR
30 - 16 NEW VEHICLE PREPARATIONBR/BE
ROAD TEST (Continued)

INSPECTION - PARKING BRAKE
(1) Ensure that the parking brake is easy to oper-
ate (Fig. 40).
(2) Make sure the parking brake does not drag.
(3) With the vehicle stopped on a grade, firmly
apply the service brakes, place the transmission in
NEUTRAL and set the parking brake. Slowly release
the service brakes to see if the parking brake will
hold.
(4) Check that the parking brake warning light
comes on when the parking brake is applied, and is
off when the brake is released.
INSPECTION - SERVICE BRAKES
(1) Check brake warning light operation at vehicle
startup.
(2) Check ABS warning light operation at vehicle
startup.
(3) Inspect service brake pedal travel and feel (Fig.
41).
(4) Put the vehicle in gear and apply the brakes
while the car is in motion. Be sure brake operation is
smooth and positive.
(5) Make sure that the vehicle stops in a straight
line, without pulling to one side.
(6) Check that the brakes operate quietly, without
noise.
(7) Ensure there is no shudder or vibration when
braking.
INSPECTION - SPEED CONTROL
Check the following speed control functions (Fig.
42):²Check on/off switch
²Check ªsetº operation
²Check ªresumeº function
²Check ªaccelerateº and ªdecelerateº functions
²Check brake release function
²Check ªcancelº function
INSPECTION - TRIP COMPUTER/
MAINTENANCE REMINDER
NOTE: Reset the average fuel economy when the
road test is complete.
Check that all modes operate correctly (Fig. 43).
INSPECTION - RADIO
(1) Check for good AM/FM reception, ensure that
the cassette and/or compact disc (CD) player works
properly (Fig. 44).
(2) Check for good sound quality from all speakers.
(3) Ensure that the radio displays the correct time.
(4) Check the steering wheel controls (if equipped).
INSPECTION - HEATER/AIR CONDITIONER
(1) Check that heater/defroster works properly
(Fig. 45).
(2) Turn on the heater when the engine reaches
operating temperature.
(3) Operate the blower motor in all speeds.
(4) Operate system in all modes (heat, defrost,
etc.).
(5) Operate the rear heater (if equipped).
(6) Check for hot air output at all outlets.
Fig. 40 PARKING BRAKE OPERATION
Fig. 41 SERVICE BRAKE PEDAL
BR/BENEW VEHICLE PREPARATION 30 - 17
ROAD TEST (Continued)

INSPECTION - MIRROR
(1) Check operation of rearview mirror's day/night
function (if equipped).
(2) Check ease of adjustment for all mirrors (power
or manual) (Fig. 46) and (Fig. 47).
INSPECTION - TURN AND EMERGENCY
SIGNALS
(1) Ensure that the turn signals work properly
(including canceling after completing a turn).
(2) Ensure that the emergency flashers work prop-
erly.
INSPECTION - HORN
Ensure that the horn works properly.
INSPECTION - GAUGES/WARNING LIGHTS
(1) Ensure that all gauges, instrument indicator
lights, warning lights and instrument panel lights
are functioning properly.
(2) Inspect operation of message center (if
equipped).
INSPECTION - SHIFT/CLUTCH INTERLOCK
SYSTEM
(1) On vehicles with a manual transmission or
transaxle, be sure engine starts only when clutch is
depressed.
(2) Some vehicles equipped with an automatic
transmission also have a brake interlock system. On
these vehicles, be sure that you cannot shift out of
PARK without pressing the brake pedal.
INSPECTION - NEUTRAL SAFETY SWITCH
(1) On vehicles with an automatic transmission or
transaxle, check shift indicator alignment in all
ranges.
(2) Be sure the engine starts in both PARK and
NEUTRAL.
(3) Verify that the engine does not start in any
REVERSE/DRIVE positions.
PRE DELIVERY STORAGE
DESCRIPTION
Pre Delivery Storage information is provided to
recommend practices to use when storing new vehi-
cles prior to delivery to the customer.
If you have prepared a vehicle that will not be
immediately delivered to the customer, store the
vehicle according to guidelines outlined in (Refer to
30 - NEW VEHICLE PREP/PREDELIVERY STOR-
AGE - STANDARD PROCEDURE) to prevent unnec-
essary wear and tear on the vehicles electrical
systems, paint and finish and damage due to pilfer-
age and vandalism.
Fig. 46 INSIDE REAR VIEW MIRROR
Fig. 47 OUTSIDE REAR VIEW MIRROR
BR/BENEW VEHICLE PREPARATION 30 - 19
ROAD TEST (Continued)

STANDARD PROCEDURE - PRE DELIVERY
STORAGE
(1) If possible, store vehicles indoors, in clean, dry
places. If vehicles must be stored outdoors:
²Try to avoid storage locations that are near any
obvious sources of industrial or environmental con-
tamination (e.g., trees, factories, steam or vapor
vents, railroad tracks, etc.)
²Maintain tight security to help prevent pilferage
and vandalism, and inspect each vehicle regularly to
check for such damage
²If the vehicle must be parked on an incline, park
it with the front end higher than the rear; this will
prevent ªhydrostatic lockº caused by fuel draining
into the engine
²Rinse the vehicle at least once a week. Snow
should be washed away more often, since it can trap
harmful contaminants. Dry all horizontal surfaces
(2) The IOD fuse should be removed in order to
prevent battery drain and possible damage.
(3) Check the vehicle's coolant and anti-freeze pro-
tection.
(4) Check the vehicle's battery at least once a
month for a proper charge (at least 12.4 volts).
Charge the battery if necessary. This will help pre-
vent freezing and deterioration.
(5) Check the vehicle's tires and inflate them to
their maximum recommended levels. Move the vehi-
cles periodically to avoid ªflatspottingº the tires.
(6) Do not engage the parking brake; keep it in the
OFF position.
(7) Keep all windows closed, all doors locked, and
all trim covers intact and in place.
(8) Do not use chalks, crayons or any marker con-
taining abrasives on painted, plated or glass sur-
faces.
(9) Always use seat covers when moving a vehicle.
PROGRAMMABLE
ELECTRONIC FEATURES
DESCRIPTION
The programming of electronic features applies to
specific DaimlerChrysler Corporation vehicles. Not
all vehicles are equipped with these electronic fea-
tures, and not all vehicles equipped with electronic
features have all the available features. Programma-
ble electronic features are subject to change and may
be added or deleted from specific vehicle models.
(1) The programmable electronic features that may
be provided on the vehicle are:
²Rolling Power Door Locks
²Horn Chirp (When Doors Locked With Remote
Keyless Entry)²Headlamp Flash (When Doors Locked or
Unlocked With Remote Keyless Entry)
²Low Fuel Chime
²Remote Keyless Entry Door Unlock Sequence
²Headlights On Automatically With Wipers
²Turn Signal Chime
²12V Power Outlet
²Remote Unlock
²Remote Linked To Memory
²Headlamp Delay
²Service Interval
²Easy Exit Seat
(2) Programming any of the above features is to be
performed prior to vehicle delivery to the customer,
depending on customer preference.
NOTE: For all vehicles except Caravan/Town and
Country, the programming must be performed using
the DRB IIITscan tool. On Caravan/Town and Coun-
try vehicles the features can be programmed using
the DRB IIITscan tool or by button pushing
sequences. The customer can perform program-
ming, if desired, by following the instructions out-
lined in the owner manual.
OPERATION
NOTE: The programmable features provided on
vehicles need to be explained to the customer at
the time of sale. The customer's preferences con-
cerning the features should be noted and pro-
grammed accordingly during predelivery.
NOTE: When using the DRB IIITscan tool to enable/
disable any programmable electronic features, go to
the main menu item #9 on the DRB IIITscan tool.
This is ªCustomer Preferencesº. You must choose
ªCustomer Preferencesº on the main menu to pro-
gram the desired features.
ROLLING POWER DOOR LOCKS
With this feature enabled, the vehicle's door lock-
ing mechanisms automatically lock when the vehicle
reaches approximately 24 Km/h (15 mph).
HORN CHIRP
NOTE: This feature can be enabled with or without
the headlamp flash feature.
The horn chirp function is a feature that can be
enabled or disabled on vehicles equipped with
30 - 20 NEW VEHICLE PREPARATIONBR/BE
PRE DELIVERY STORAGE (Continued)

CABLE - INSTALLATION, RELEASE.......23-83
CABLE - INSTALLATION, SPARK PLUG....8I-20
CABLE - INSTALLATION, THROTTLE
CONTROL....................14-105,14-50
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - OPERATION, BATTERY..........8F-20
CABLE - OPERATION, SPARK PLUG.......8I-19
CABLE - REMOVAL, CHECK.............23-62
CABLE - REMOVAL, FRONT PARKING
BRAKE..............................5-37
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-9
CABLE - REMOVAL, LATCH RELEASE....23-101
CABLE - REMOVAL, RELEASE...........23-82
CABLE - REMOVAL, SPARK PLUG........8I-20
CABLE - REMOVAL, THROTTLE
CONTROL....................14-104,14-50
CABLE 2500/3500 SERIES WITH DRUM
BRAKES - INSTALLATION, REAR PARK
BRAKE..............................5-39
CABLE INSTALLATION, GASOLINE -
NEGATIVE..........................8F-24
CABLE INSTALLATION, GASOLINE -
POSITIVE...........................8F-23
CABLE ORDER, 8.0L V-10 ENGINE -
SPARK PLUG.........................8I-2
CABLE REMOVAL, GASOLINE -
NEGATIVE..........................8F-23
CABLE REMOVAL, GASOLINE - POSITIVE . . 8F-23
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-3
CABLE TENSIONER - ADJUSTMENT.......5-40
CABLES - 1500 SERIES - INSTALLATION,
REAR PARK BRAKE....................5-39
CABLES - 1500 SERIES - REMOVAL,
REAR PARK BRAKE....................5-37
CABLES - DIAGNOSIS & TESTING,
BATTERY...........................8F-20
CABLES - DIAGNOSIS AND TESTING,
SPARK PLUG........................8I-19
CABLES 2500/3500 SERIES WITH DRUM
BRAKES - REMOVAL, REAR PARK
BRAKE..............................5-38
CAB-TO- BED GROUND STRAP -
INSTALLATION.......................8A-14
CAB-TO- BED GROUND STRAP -
REMOVAL..........................8A-14
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-4
CALIPERS - ASSEMBLY, DISC BRAKE......5-12
CALIPERS - CLEANING, DISC BRAKE......5-12
CALIPERS - DISASSEMBLY, DISC BRAKE . . . 5-11
CALIPERS - INSPECTION, DISC BRAKE....5-12
CAM - DESCRIPTION, TURN SIGNAL
CANCEL............................8L-30
CAM - OPERATION, TURN SIGNAL
CANCEL............................8L-31
CAM BORE REPAIR - STANDARD
PROCEDURE........................9-267
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING
CLUTCH.........21-236,21-406,21-581,21-752
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAMSHAFT & BEARINGS (IN BLOCK) -
INSPECTION
........................9-272
CAMSHAFT - INSTALLATION
. 9-144,9-201,9-273,
9-29,9-87
CAMSHAFT - REMOVAL
. 9-143,9-201,9-268,9-29,
9-86
CAMSHAFT BEARINGS - INSTALLATION
. . 9-144,
9-201,9-273,9-29,9-87
CAMSHAFT BEARINGS - REMOVAL
. 9-143,9-200,
9-268,9-29,9-86CANCEL CAM - DESCRIPTION, TURN
SIGNAL............................8L-30
CANCEL CAM - OPERATION, TURN
SIGNAL............................8L-31
CANISTER - DESCRIPTION, VAPOR......25-37
CANISTER - INSTALLATION, CRANKCASE
BREATHER VAPOR...................9-242
CANISTER - INSTALLATION, VAPOR......25-38
CANISTER - OPERATION, VAPOR........25-37
CANISTER - REMOVAL, CRANKCASE
BREATHER VAPOR...................9-241
CANISTER - REMOVAL, VAPOR..........25-37
CAP - CLEANING, RADIATOR PRESSURE . . . 7-66
CAP - DESCRIPTION, FUEL FILLER.......25-33
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-65
CAP - DIAGNOSIS AND TESTING,
DISTRIBUTOR.......................8I-12
CAP - DIAGNOSIS AND TESTING,
RADIATOR...........................7-66
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-66
CAP - OPERATION, FUEL FILLER........25-33
CAP - OPERATION, RADIATOR
PRESSURE..........................7-65
CAP - REMOVAL/INSTALLATION, FUEL
FILLER.............................25-33
CAPACITIES, SPECIFICATIONS - FLUID......0-6
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP..................14-9
CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR.....7-66
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE.................3-11
CARDAN UNIVERSAL JOINTS -
INSTALLATION, SINGLE............3-34,3-66
CARDAN UNIVERSAL JOINTS -
REMOVAL, SINGLE................3-33,3-65
CAREFUL NEW VEHICLE PREPARATION -
DESCRIPTION, THE IMPORTANCE OF......30-1
CARGO BOX - INSTALLATION...........23-97
CARGO BOX - REMOVAL...............23-96
CARGO DOOR - ADJUSTMENT..........23-78
CARPETS AND FLOOR MATS -
INSTALLATION......................23-123
CARPETS AND FLOOR MATS - REMOVAL . 23-123
CARTRIDGE FUSE - DESCRIPTION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - INSTALLATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - OPERATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - REMOVAL,
GENERATOR......................8W-97-4
CASE - DIAGNOSIS AND TESTING,
TRANSFER.............21-821,21-856,21-892
CASE - INSPECTION, TRANSMISSION/
TRANSFER..........................30-15
CASE - NV231HD - ASSEMBLY,
TRANSFER.........................21-834
CASE - NV231HD - CLEANING,
TRANSFER.........................21-831
CASE - NV231HD - DESCRIPTION,
TRANSFER.........................21-820
CASE - NV231HD - DISASSEMBLY,
TRANSFER.........................21-822
CASE - NV231HD - INSPECTION,
TRANSFER.........................21-832
CASE - NV231HD - INSTALLATION,
TRANSFER.........................21-847
CASE - NV231HD - OPERATION,
TRANSFER.........................21-820
CASE - NV231HD - REMOVAL,
TRANSFER.........................21-822
CASE - NV241HD - ASSEMBLY,
TRANSFER.........................21-904
CASE - NV241HD - CLEANING,
TRANSFER.........................21-902
CASE - NV241HD - DESCRIPTION,
TRANSFER
.........................21-890
CASE - NV241HD - DISASSEMBLY,
TRANSFER
.........................21-894
CASE - NV241HD - INSPECTION,
TRANSFER
.........................21-902
CASE - NV241HD - INSTALLATION,
TRANSFER
.........................21-919
CASE - NV241HD - OPERATION,
TRANSFER
.........................21-892CASE - NV241HD - REMOVAL,
TRANSFER.........................21-894
CASE - NV241LD - ASSEMBLY,
TRANSFER.........................21-869
CASE - NV241LD - CLEANING,
TRANSFER.........................21-866
CASE - NV241LD - DESCRIPTION,
TRANSFER.........................21-855
CASE - NV241LD - DISASSEMBLY,
TRANSFER.........................21-858
CASE - NV241LD - INSPECTION,
TRANSFER.........................21-867
CASE - NV241LD - INSTALLATION,
TRANSFER.........................21-882
CASE - NV241LD - OPERATION,
TRANSFER.........................21-855
CASE - NV241LD - REMOVAL,
TRANSFER.........................21-858
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE BEARINGS - REMOVAL,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE FLUID - DESCRIPTION, TRANSFER....0-5
CASE, NV231HD - TRANSFER..........21-849
CASE, NV241HD - TRANSFER..........21-920
CASE, NV241LD - TRANSFER..........21-884
CASE SKID PLATE - INSTALLATION,
TRANSFER..........................13-11
CASE SKID PLATE - REMOVAL,
TRANSFER..........................13-11
CASE, SPECIFICATIONS - TRANSFER.....21-848,
21-883,21-919
CASTER CORRECTION MEASUREMENT -
STANDARD PROCEDURES...............2-3
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- DESCRIPTION.......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSPECTION........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSTALLATION......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- OPERATION.........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- REMOVAL..........................11-5
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - DESCRIPTION..............11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSPECTION...............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSTALLATION.............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - OPERATION................11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - REMOVAL.................11-6
CATCH - INSPECTION, HOOD LATCH/
SAFETY.............................30-4
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
CAUTION, INTERIOR.................23-118
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-42
CCD DATA BUS - DESCRIPTION..........8E-6
CCD DATA BUS - DIAGNOSIS AND
TESTING...........................8E-11
CCD DATA BUS - OPERATION............8E-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-7
CENTER - INSTALLATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - OPERATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - REMOVAL, POWER
DISTRIBUTION
....................8W-97-8
CENTER BEARING - CENTER BEARING
ADJUSTMENT
........................3-10
CENTER BEARING - DESCRIPTION
........3-10
CENTER BEARING - INSTALLATION
.......3-10
CENTER BEARING - OPERATION
..........3-10
CENTER BEARING - REMOVAL
...........3-10
CENTER BEARING ADJUSTMENT,
CENTER BEARING
.....................3-10
CENTER CONSOLE - INSTALLATION
.....23-122
CENTER CONSOLE - REMOVAL
.........23-122
CENTER CONSOLE LID - INSTALLATION
. . 23-132
CENTER CONSOLE LID - REMOVAL
.....23-131
6 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

CENTER HIGH MOUNTED STOP LAMP -
INSTALLATION........................8L-6
CENTER HIGH MOUNTED STOP LAMP -
REMOVAL...........................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION..................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL.....................8L-6
CENTER SEAT ARMREST/CONSOLE -
INSTALLATION......................23-132
CENTER SEAT ARMREST/CONSOLE -
REMOVAL.........................23-132
CENTER SEAT ARMREST/LATCH COVER -
INSTALLATION......................23-132
CENTER SEAT ARMREST/LATCH COVER -
REMOVAL.........................23-132
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-11
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING........................8E-4
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY..................Intro.-12
CHAIN COVER(S) - INSTALLATION,
TIMING BELT..........9-113,9-169,9-226,9-56
CHAIN COVER(S) - REMOVAL, TIMING
BELT ................9-113,9-169,9-225,9-56
CHAIN STRETCH - INSPECTION,
MEASURING TIMING....9-114,9-170,9-227,9-58
CHANNEL - INSTALLATION, GLASS RUN . . 23-70
CHANNEL - REMOVAL, GLASS RUN......23-70
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-46
CHARGE AIR COOLER AND PLUMBING -
CLEANING..........................11-18
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION.......................11-17
CHARGE AIR COOLER AND PLUMBING -
INSPECTION........................11-18
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION.......................11-18
CHARGE AIR COOLER AND PLUMBING -
OPERATION.........................11-17
CHARGE AIR COOLER AND PLUMBING -
REMOVAL..........................11-17
CHARGING - DESCRIPTION.............8F-27
CHARGING - OPERATION..............8F-27
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-9
CHARGING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-27
CHART, SPECIFICATIONS - TORQUE........5-3
CHART, SPECIFICATIONS -
TORQUE.............19-19,19-39,19-41,19-9
CHART, SPECIFICATIONS -
TORQUE.....................2-15,2-27,2-8
CHART, SPECIFICATIONS - TORQUE......22-11
CHARTS - DIAGNOSIS AND TESTING,
DIAGNOSIS......21-149,21-320,21-492,21-663
CHARTS - DIAGNOSIS AND TESTING,
SMOKE DIAGNOSIS...................9-234
CHASSIS ADAPTER BRACKET -
INSTALLATION, CAB...................13-9
CHASSIS ADAPTER BRACKET -
REMOVAL, CAB.......................13-9
CHECK - INSTALLATION...............23-78
CHECK - REMOVAL...................23-78
CHECK - STANDARD PROCEDURE,
COOLANT LEVEL......................7-16
CHECK - STANDARD PROCEDURE, FLUID
LEVEL..........21-199,21-370,21-545,21-715
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME . . . 21-209,21-379,21-554,21-724
CHECK CABLE - INSTALLATION.........23-63
CHECK CABLE - REMOVAL.............23-62
CHECK GAUGES INDICATOR -
DESCRIPTION.......................8J-17
CHECK GAUGES INDICATOR -
OPERATION.........................8J-17
CHECK OUT - STANDARD PROCEDURE,
OWNER............................30-22
CHECK VALVE - DESCRIPTION, ONE WAY . 25-30
CHECK VALVE - DESCRIPTION, VACUUM
. . 24-28
CHECK VALVE - DIAGNOSIS AND
TESTING, ONE-WAY
..................25-30
CHECK VALVE - INSTALLATION, ONE
WAY
...............................25-30
CHECK VALVE - INSTALLATION, VACUUM
. 24-29
CHECK VALVE - OPERATION, ONE WAY
. . . 25-30CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, ONE WAY....25-30
CHECK VALVE - REMOVAL, VACUUM.....24-29
CHECKING BATTERY ELECTROLYTE
LEVEL - STANDARD PROCEDURE.........8F-8
CHECKING TRANSMISSION CLUTCH AND
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR................21-147,21-318
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-4
CHILD TETHER - INSTALLATION..........8O-9
CHILD TETHER - REMOVAL.............8O-9
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-2
CHIME WARNING SYSTEM - OPERATION . . . 8B-1
CHOKE RELAY - DESCRIPTION, RADIO....8A-8
CHOKE RELAY - DIAGNOSIS AND
TESTING, RADIO......................8A-8
CHOKE RELAY - INSTALLATION, RADIO....8A-9
CHOKE RELAY - OPERATION, RADIO......8A-8
CHOKE RELAY - REMOVAL, RADIO.......8A-9
CIGAR LIGHTER - DIAGNOSIS &
TESTING.........................8W-97-2
CIGAR LIGHTER OUTLET - DESCRIPTION . 8W-97-2
CIGAR LIGHTER OUTLET -
INSTALLATION....................8W-97-3
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL....8W-97-3
CIRCUIT ACTUATION TEST MODE -
DESCRIPTION........................25-1
CIRCUIT BREAKER - DESCRIPTION....8W-97-4
CIRCUIT BREAKER - DIAGNOSIS &
TESTING.........................8W-97-4
CIRCUIT SENSE - DESCRIPTION,
IGNITION...........................8E-17
CIRCUIT SENSE - OPERATION, IGNITION . . 8E-19
CIRCUITS - DIESEL - OPERATION,
NON-MONITORED....................25-23
CIRCUITS - GAS ENGINES - OPERATION,
NON-MONITORED....................25-22
CLAMPS - DESCRIPTION, HOSE...........7-2
CLAMPS - OPERATION, HOSE.............7-2
CLASSIFICATION OF LUBRICANTS -
STANDARD PROCEDURE.................0-3
CLEANER ELEMENT - INSTALLATION,
AIR ...............................9-245
CLEANER ELEMENT - REMOVAL, AIR.....9-244
CLEANING AND INSPECTION, OIL
COOLER & LINES....................9-296
CLEANING, APPEARANCE TIPS..........30-21
CLEANING/REVERSE FLUSHING -
STANDARD PROCEDURE, COOLING
SYSTEM............................7-16
CLEARANCE - STANDARD PROCEDURE,
CONNECTING ROD BEARING AND
CRANKSHAFT JOURNAL...............9-274
CLEARANCE - STANDARD PROCEDURE,
MAIN BEARING......................9-275
CLEARANCE LAMP - INSTALLATION.......8L-6
CLEARANCE LAMP - REMOVAL..........8L-6
CLOCKSPRING - DESCRIPTION.........8O-10
CLOCKSPRING - INSTALLATION.........8O-13
CLOCKSPRING - OPERATION...........8O-10
CLOCKSPRING - REMOVAL............8O-11
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-11
CLOSURE PANEL TRIM - INSTALLATION,
REAR.............................23-121
CLOSURE PANEL TRIM - REMOVAL,
REAR.............................23-120
CLUB/QUAD CAB - INSTALLATION.......8O-20
CLUB/QUAD CAB - REMOVAL...........8O-19
CLUSTER - ASSEMBLY, INSTRUMENT....8J-13
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-6
CLUSTER - DISASSEMBLY, INSTRUMENT . . 8J-11
CLUSTER - INSTALLATION, INSTRUMENT . 8J-14
CLUSTER - OPERATION, INSTRUMENT.....8J-3
CLUSTER - REMOVAL, INSTRUMENT
.....8J-10
CLUSTER BEZEL - INSTALLATION
.......23-110
CLUSTER BEZEL - REMOVAL
..........23-109
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
DESCRIPTION, FAN DRIVE VISCOUS
......7-56
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
OPERATION, FAN DRIVE VISCOUS
........7-56CLUTCH - 5.9L DIESEL - DESCRIPTION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - 5.9L DIESEL - OPERATION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - ASSEMBLY, FRONT . . . 21-206,21-376,
21-550,21-721
CLUTCH - ASSEMBLY, REAR....21-248,21-419,
21-593,21-766
CLUTCH - CLEANING, REAR....21-247,21-418,
21-593,21-765
CLUTCH - DESCRIPTION.................6-1
CLUTCH - DESCRIPTION, A/C
COMPRESSOR.......................24-13
CLUTCH - DESCRIPTION, FRONT . 21-202,21-373,
21-548,21-718
CLUTCH - DESCRIPTION, OVERDRIVE . . . 21-214,
21-385,21-560,21-731
CLUTCH - DESCRIPTION, REAR . . 21-246,21-417,
21-591,21-764
CLUTCH - DIAGNOSTIC AND TESTING......6-2
CLUTCH - DISASSEMBLY, FRONT......21-202,
21-373,21-549,21-719
CLUTCH - DISASSEMBLY, REAR . 21-247,21-418,
21-592,21-765
CLUTCH - INSPECTION, A/C
COMPRESSOR.......................24-16
CLUTCH - INSPECTION, FRONT . . 21-205,21-376,
21-550,21-721
CLUTCH - INSPECTION, REAR . . . 21-248,21-419,
21-593,21-765
CLUTCH - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH - OPERATION....................6-1
CLUTCH - OPERATION, A/C
COMPRESSOR.......................24-13
CLUTCH - OPERATION, FRONT . . 21-202,21-373,
21-548,21-718
CLUTCH - OPERATION, OVERDRIVE....21-214,
21-385,21-560,21-731
CLUTCH - OPERATION, REAR . . . 21-246,21-417,
21-592,21-764
CLUTCH - REMOVAL, A/C COMPRESSOR . . 24-14
CLUTCH - SPECIFICATIONS...............6-7
CLUTCH - WARNING....................6-2
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING TRANSMISSION......21-147,21-318
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
TESTING TRANSMISSION.......21-490,21-661
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-13
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - ASSEMBLY,
OVERRUNNING . . . 21-236,21-406,21-581,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - CLEANING, OVERRUNNING . 21-236,
21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DESCRIPTION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DISASSEMBLY,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - INSPECTION,
OVERRUNNING . . . 21-236,21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - OPERATION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-13
CLUTCH DISC - DESCRIPTION............6-7
CLUTCH DISC - INSTALLATION............6-9
CLUTCH DISC - OPERATION..............6-8
CLUTCH DISC - REMOVAL...............6-8
CLUTCH HOUSING - DIAGNOSIS AND
TESTING............................6-11
CLUTCH HOUSING - INSTALLATION.......6-13
CLUTCH HOUSING - REMOVAL...........6-13
CLUTCH PEDAL - INSTALLATION
.........6-19
CLUTCH PEDAL - REMOVAL
.............6-18
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION
........................6-22
CLUTCH PEDAL POSITION SWITCH -
OPERATION
..........................6-22
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR
.......................24-17
BR/BEINDEX 7
Description Group-Page Description Group-Page Description Group-Page

CONTROL/CENTRAL TIMER MODULE -
INSTALLATION, BODY..................8E-6
CONTROL/CENTRAL TIMER MODULE -
OPERATION, BODY....................8E-3
CONTROL/CENTRAL TIMER MODULE -
REMOVAL, BODY......................8E-5
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION.......................8E-11
CONTROLLER ANTILOCK BRAKE -
INSTALLATION.......................8E-12
CONTROLLER ANTILOCK BRAKE -
OPERATION.........................8E-11
CONTROLLER ANTILOCK BRAKE -
REMOVAL..........................8E-12
CONTROLS - DIAGNOSIS AND TESTING,
OVERDRIVE
ELECTRICAL.....21-215,21-386,21-579,21-732
CONVERTER - 3.9L/5.2L/5.9L -
DESCRIPTION, CATALYTIC...............11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSPECTION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSTALLATION, CATALYTIC..............11-5
CONVERTER - 3.9L/5.2L/5.9L -
OPERATION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
REMOVAL, CATALYTIC..................11-5
CONVERTER - 5.9L HEAVY DUTY/8.0L -
DESCRIPTION, CATALYTIC...............11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSPECTION, CATALYTIC................11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSTALLATION, CATALYTIC..............11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
OPERATION, CATALYTIC................11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
REMOVAL, CATALYTIC..................11-6
CONVERTER - DESCRIPTION,
TORQUE........21-256,21-427,21-600,21-773
CONVERTER - INSTALLATION,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER - OPERATION,
TORQUE........21-260,21-430,21-604,21-777
CONVERTER - REMOVAL,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
DESCRIPTION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
OPERATION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
STANDARD PROCEDURE,
TORQUE........21-262,21-432,21-606,21-778
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND
TESTING........21-148,21-319,21-491,21-662
COOLANT - DESCRIPTION...............7-40
COOLANT - OPERATION
................7-40
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
..................7-16
COOLANT FLOW - DIAGNOSIS AND
TESTING, RADIATOR
...........7-59,7-61,7-63
COOLANT LEVEL CHECK - STANDARD
PROCEDURE
.........................7-16
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
DESCRIPTION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
INSTALLATION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
OPERATION
..........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
REMOVAL
...........................7-41
COOLANT RECOVERY CONTAINER - 8.0L
- DESCRIPTION
.......................7-42
COOLANT RECOVERY CONTAINER - 8.0L
- OPERATION
.........................7-42
COOLANT SELECTION-ADDITIVES -
STANDARD PROCEDURE
................7-17
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE
............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE
...........7-48COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-48
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE...........7-50
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-49
COOLANT THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE................7-55
COOLANT THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE...................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE....................7-55
COOLANT THERMOSTAT - 8.0L -
DESCRIPTION, ENGINE.................7-52
COOLANT THERMOSTAT - 8.0L -
INSTALLATION, ENGINE................7-53
COOLANT THERMOSTAT - 8.0L -
OPERATION, ENGINE...................7-52
COOLANT THERMOSTAT - 8.0L -
REMOVAL, ENGINE....................7-52
COOLER - 3.9L/5.2L/5.9L - ASSEMBLY,
TRANS..............................7-82
COOLER - 3.9L/5.2L/5.9L -
DESCRIPTION, TRANS.................7-79
COOLER - 3.9L/5.2L/5.9L -
DISASSEMBLY, TRANS...................7-81
COOLER - 3.9L/5.2L/5.9L -
INSTALLATION, TRANS.................7-82
COOLER - 3.9L/5.2L/5.9L - OPERATION,
TRANS..............................7-79
COOLER - 3.9L/5.2L/5.9L - REMOVAL,
TRANS..............................7-81
COOLER - 5.9L DIESEL - DESCRIPTION,
TRANS..............................7-85
COOLER - 5.9L DIESEL - INSTALLATION,
TRANS..............................7-88
COOLER - 5.9L DIESEL - OPERATION,
TRANS..............................7-85
COOLER - 8.0L - DESCRIPTION, TRANS....7-82
COOLER - 8.0L - INSTALLATION, TRANS . . . 7-85
COOLER - 8.0L - OPERATION, TRANS.....7-82
COOLER - 8.0L - REMOVAL, TRANS.......7-84
COOLER - INSTALLATION, AIR TO OIL.....7-88
COOLER & LINES - CLEANING AND
INSPECTION, OIL.....................9-296
COOLER - REMOVAL, AIR TO OIL.........7-87
COOLER - REMOVAL, WATER TO OIL......7-87
COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL...........7-80,7-83,7-86
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION OIL...........7-79,7-83,7-85
COOLER AND PLUMBING - CLEANING,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR............11-17
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR...........11-18
COOLER AND PLUMBING - OPERATION,
CHARGE AIR........................11-17
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR........................11-17
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-80,7-83,7-86
COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-79,7-83,7-85
COOLING, SPECIAL TOOLS
..............7-18
COOLING SYSTEM - OPERATION
..........7-4
COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
DRAINING
...........................7-15COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
REFILLING...........................7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, DRAINING.....7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, REFILLING.....7-15
COOLING SYSTEM CLEANING/REVERSE
FLUSHING - STANDARD PROCEDURE.....7-16
COOLING SYSTEM DIESEL ENGINE -
DIAGNOSIS AND TESTING..............7-12
COOLING SYSTEM FLOW - 3.9L/5.2L/
5.9L ENGINE - DESCRIPTION.............7-1
COOLING SYSTEM FLOW - 5.9L DIESEL
- DESCRIPTION........................7-1
COOLING SYSTEM GAS ENGINE -
DIAGNOSIS AND TESTING...............7-7
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-5
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-55
CORE - INSTALLATION, HEATER.........24-56
CORE - OPERATION, HEATER...........24-55
CORE - REMOVAL, HEATER............24-56
CORE GROUND STRAP - INSTALLATION,
HEATER............................8A-15
CORE GROUND STRAP - REMOVAL,
HEATER............................8A-14
CORNER SEAL - INSTALLATION, FRONT
DOOR UPPER......................23-154
CORNER SEAL - REMOVAL, FRONT
DOOR UPPER........................23-154
COUPLERS - DESCRIPTION, A/C LINE....24-40
COUPLERS - OPERATION, A/C LINE......24-41
COUPLERS - STANDARD PROCEDURE,
A/C LINE...........................24-43
COVER - INSTALLATION, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - INSTALLATION, COWL TRIM . . . 23-120
COVER - INSTALLATION, GEAR HOUSING . 9-307
COVER - INSTALLATION, INSTRUMENT
PANEL TOP........................23-115
COVER - INSTALLATION, SEAT BACK....23-137
COVER - INSTALLATION, SEAT CUSHION . 23-139
COVER - INSTALLATION, SHIFT . . . 21-133,21-90
COVER - INSTALLATION, STANCHION....23-143
COVER - INSTALLATION, STEERING
COLUMN OPENING..................23-116
COVER - REMOVAL, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - REMOVAL, COWL TRIM.......23-119
COVER - REMOVAL, GEAR HOUSING.....9-306
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-114
COVER - REMOVAL, SEAT BACK........23-137
COVER - REMOVAL, SEAT CUSHION.....23-139
COVER - REMOVAL, SHIFT.......21-132,21-90
COVER - REMOVAL, STANCHION.......23-143
COVER - REMOVAL, STEERING COLUMN
OPENING..........................23-115
COVER - REMOVAL, WHEEL............22-12
COVER - SPLIT BENCH - INSTALLATION,
SEAT BACK........................23-138
COVER - SPLIT BENCH - INSTALLATION,
SEAT CUSHION.....................23-140
COVER - SPLIT BENCH - REMOVAL,
SEAT BACK........................23-137
COVER - SPLIT BENCH - REMOVAL,
SEAT CUSHION.....................23-139
COVER GASKET - DESCRIPTION,
CYLINDER...........................9-79
COVER GASKET - DESCRIPTION,
CYLINDER HEAD......................9-22
COVER GASKET - OPERATION,
CYLINDER HEAD......................9-22
COVER INSTALLED - INSTALLATION,
FRONT OIL SEAL - FRONT.............9-205
COVER INSTALLED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER REMOVED - INSTALLATION,
FRONT OIL SEAL - FRONT
.............9-205
COVER REMOVED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER(S) - CLEANING, CYLINDER HEAD
. 9-138,
9-194,9-24,9-253,9-81
COVER(S) - DESCRIPTION, CYLINDER
HEAD
..............................9-194
BR/BEINDEX 9
Description Group-Page Description Group-Page Description Group-Page

DOOR CYLINDER LOCK SWITCH -
OPERATION..........................8N-5
DOOR CYLINDER LOCK SWITCH -
REMOVAL...........................8N-6
DOOR FORE/AFT - ADJUSTMENT, FRONT . . 23-68
DOOR GLASS - INSTALLATION..........23-69
DOOR GLASS - REMOVAL.............23-69
DOOR GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT...............23-154
DOOR GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT...................23-153
DOOR INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT...............23-154
DOOR INNER BELT WEATHERSTRIP -
REMOVAL, FRONT...................23-154
DOOR IN/OUT - ADJUSTMENT, FRONT....23-69
DOOR LATCH - ADJUSTMENT, FRONT....23-72
DOOR LOCKS - INSPECTION, DOORS.....30-11
DOOR OPENING SEAL - INSTALLATION . . 23-153
DOOR OPENING SEAL - REMOVAL......23-153
DOOR OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT...............23-154
DOOR OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT...................23-154
DOOR SEAL - INSTALLATION, B-PILLAR . 23-152
DOOR SEAL - REMOVAL, B-PILLAR.....23-152
DOOR SECOND WEATHERSTRIP -
INSTALLATION, FRONT...............23-155
DOOR SECOND WEATHERSTRIP -
REMOVAL, FRONT...................23-154
DOOR SILL TRIM - INSTALLATION......23-121
DOOR SILL TRIM - REMOVAL.........23-121
DOOR SPEAKER - INSTALLATION, FRONT . 8A-20
DOOR SPEAKER - INSTALLATION, REAR . . 8A-21
DOOR SPEAKER - REMOVAL, FRONT.....8A-20
DOOR SPEAKER - REMOVAL, REAR......8A-21
DOOR UP/DOWN - ADJUSTMENT, FRONT . 23-69
DOOR UPPER CORNER SEAL -
INSTALLATION, FRONT...............23-154
DOOR UPPER CORNER SEAL -
REMOVAL, FRONT...................23-154
DOORS AND DOOR LOCKS -
INSPECTION........................30-11
DOORS AND LOCKS - INSPECTION,
WINDOWS..........................30-14
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE.................5-8
DRAIN AND REFILL - STANDARD
PROCEDURE, FLUID.....21-851,21-885,21-922
DRAIN MANIFOLD - DESCRIPTION, FUEL . . 14-86
DRAIN MANIFOLD - INSTALLATION,
FUEL..............................14-86
DRAIN MANIFOLD - OPERATION, FUEL . . . 14-86
DRAIN MANIFOLD - REMOVAL, FUEL.....14-86
DRAINBACK VALVE - DESCRIPTION,
TORQUE CONVERTER....21-262,21-432,21-605,
21-778
DRAINBACK VALVE - OPERATION,
TORQUE CONVERTER....21-262,21-432,21-605,
21-778
DRAINBACK VALVE - STANDARD
PROCEDURE, TORQUE
CONVERTER.....21-262,21-432,21-606,21-778
DRAINING AT FUEL FILTER - STANDARD
PROCEDURES, WATER................14-56
DRAINING COOLING SYSTEM
3.9L/5.2L/5.9L/8.0L ENGINES -
STANDARD PROCEDURE................7-15
DRAINING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-15
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-15
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN....................7-56,7-58
DRIVE BELT - DIAGNOSIS AND TESTING,
ACCESSORY.................7-24,7-27,7-31
DRIVE BELTS - 3.9L/5.2L/5.9L -
INSTALLATION........................7-27
DRIVE BELTS - 3.9L/5.2L/5.9L -
REMOVAL...........................7-26
DRIVE BELTS - 5.9L DIESEL -
INSTALLATION
........................7-34
DRIVE BELTS - 5.9L DIESEL - REMOVAL
. . . 7-33
DRIVE BELTS - 8.0L - INSTALLATION
......7-30
DRIVE BELTS - 8.0L - REMOVAL
.........7-30
DRIVE INDICATOR - DIAGNOSIS AND
TESTING, FOUR-WHEEL
...............8J-29DRIVE VISCOUS CLUTCH - 3.9L/5.2L/
5.9L/8.0L - DESCRIPTION, FAN...........7-56
DRIVE VISCOUS CLUTCH - 3.9L/5.2L/
5.9L/8.0L - OPERATION, FAN............7-56
DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION, FAN............7-57
DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION, FAN..............7-57
DRIVER AIRBAG - ASSEMBLY..........8O-17
DRIVER AIRBAG - DESCRIPTION........8O-14
DRIVER AIRBAG - DISASSEMBLY........8O-15
DRIVER AIRBAG - INSTALLATION.......8O-18
DRIVER AIRBAG - OPERATION..........8O-14
DRIVER AIRBAG - REMOVAL...........8O-14
DRIVER POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
DRIVER POWER SEAT SWITCH -
DIAGNOSIS & TESTING...............8N-16
DRIVER POWER SEAT SWITCH -
INSTALLATION......................8N-17
DRIVER POWER SEAT SWITCH -
OPERATION.........................8N-16
DRIVER POWER SEAT SWITCH -
REMOVAL..........................8N-17
DRIVER SEAT HEATER SWITCH -
DESCRIPTION........................8G-7
DRIVER SEAT HEATER SWITCH -
INSTALLATION.......................8G-9
DRIVER SEAT HEATER SWITCH -
OPERATION..........................8G-7
DRIVER SEAT HEATER SWITCH -
REMOVAL.............................8G-9
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE............8W-01-7
DRUM - ADJUSTMENT, REAR BRAKE......5-34
DRUM - CLEANING....................5-33
DRUM - DESCRIPTION.................5-32
DRUM - DIAGNOSIS AND TESTING,
BRAKE..............................5-33
DRUM - INSPECTION..................5-33
DRUM - OPERATION...................5-32
DRUM BRAKES - INSTALLATION, REAR
PARK BRAKE CABLE 2500/3500
SERIES WITH........................5-39
DRUM BRAKES - REMOVAL, REAR PARK
BRAKE CABLES 2500/3500 SERIES
WITH...............................5-38
DRUM IN HAT PARK BRAKE SHOES -
2500/3500 - INSTALLATION, REAR........5-42
DRUM IN HAT PARK BRAKE SHOES -
2500/3500 - REMOVAL, REAR...........5-41
DRUM MACHINING - STANDARD
PROCEDURE, BRAKE...................5-33
DUAL REAR WHEEL INSTALLATION -
STARDARD PROCEDURE...............22-10
DUCT ADAPTER - INSTALLATION,
DEFROSTER AND DEMISTER
...........24-35
DUCT ADAPTER - REMOVAL,
DEFROSTER AND DEMISTER
...........24-35
DUCTS - INSTALLATION, DEFROSTER
AND DEMISTER
......................24-35
DUCTS - REMOVAL, DEFROSTER AND
DEMISTER
..........................24-34
DUCTS - REMOVAL, INSTRUMENT
PANEL
.............................24-37
DUCTS - REMOVAL, INSTRUMENT
PANEL DEMISTER
....................24-37
DUTY ENGINE (1500 AND 2500 MODELS
EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES - LIGHT
....................0-7
DUTY ENGINE (FEDERAL ONLY - 2500
8.0L HD AND 3500 5.9L& 8.0L
MODELS) MAINTENANCE SCHEDULES
- DESCRIPTION, HEAVY
................0-17
DUTY TRUCK MAINTENANCE SCHEDULE
(8.0L 2500 & 3500 MODELS -
CALIFORNIA ONLY) - DESCRIPTION,
MEDIUM
............................0-13
DUTY/8.0L - DESCRIPTION, CATALYTIC
CONVERTER - 5.9L HEAVY
..............11-6
DUTY/8.0L - INSPECTION, CATALYTIC
CONVERTER - 5.9L HEAVY
..............11-7
DUTY/8.0L - INSPECTION, EXHAUST
PIPE - 5.9L HEAVY
....................11-9
DUTY/8.0L - INSPECTION, TAILPIPE -
5.9L HEAVY
.........................11-12DUTY/8.0L - INSTALLATION, CATALYTIC
CONVERTER - 5.9L HEAVY..............11-7
DUTY/8.0L - INSTALLATION, EXHAUST
PIPE - 5.9L HEAVY....................11-9
DUTY/8.0L - INSTALLATION, TAILPIPE -
5.9L HEAVY.........................11-12
DUTY/8.0L - OPERATION, CATALYTIC
CONVERTER - 5.9L HEAVY..............11-6
DUTY/8.0L - REMOVAL, CATALYTIC
CONVERTER - 5.9L HEAVY..............11-6
DUTY/8.0L - REMOVAL, EXHAUST PIPE -
5.9L HEAVY..........................11-8
DUTY/8.0L - REMOVAL, TAILPIPE - 5.9L
HEAVY .............................11-12
EASY ENTRY SEAT TRACK -
INSTALLATION......................23-142
EASY ENTRY SEAT TRACK - REMOVAL . . 23-142
ECM - DESCRIPTION..................8E-13
ECM - OPERATION...................8E-13
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING......21-199,21-370,
21-545,21-715
ELECTRICAL CONTROLS - DIAGNOSIS
AND TESTING, OVERDRIVE.....21-215,21-386,
21-579,21-732
ELECTROLYTE LEVEL - STANDARD
PROCEDURE, CHECKING BATTERY........8F-8
ELECTRONIC FEATURES - DESCRIPTION,
PROGRAMMABLE....................30-20
ELECTRONIC FEATURES - OPERATION,
PROGRAMMABLE....................30-20
ELECTRONIC GOVERNOR -
DESCRIPTION....21-194,21-365,21-540,21-710
ELECTRONIC GOVERNOR -
INSTALLATION....21-197,21-367,21-543,21-713
ELECTRONIC GOVERNOR - OPERATION
. 21-194,
21-365,21-541,21-711
ELECTRONIC GOVERNOR - REMOVAL
. . . 21-196,
21-367,21-542,21-712
ELEMENT - DESCRIPTION, HEATED
SEAT
..............................8G-10
ELEMENT - INSTALLATION, AIR
CLEANER
...........................9-245
ELEMENT - OPERATION, HEATED SEAT
. . . 8G-10
ELEMENT - REMOVAL, AIR CLEANER
.....9-244
ELEMENT AND SENSOR - DIAGNOSIS &
TESTING, HEATED SEAT
...............8G-11
EMERGENCY SIGNALS - INSPECTION,
TURN
..............................30-19
END SPLASH SHIELDS - INSTALLATION,
FRONT
.............................23-92
END SPLASH SHIELDS - REMOVAL,
FRONT
.............................23-92
ENGINE - DESCRIPTION, COOLING
SYSTEM FLOW - 3.9L/5.2L/5.9L
...........7-1
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL
...............0-2
ENGINE - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIESEL
..............7-12
ENGINE - DIAGNOSIS AND TESTING,
COOLING SYSTEM GAS
.................7-7
ENGINE - DIAGNOSIS AND TESTING,
DIESEL
.............................11-4
ENGINE - DIAGNOSIS AND TESTING,
GAS
................................11-4
ENGINE - ENGINE FIRING ORDER, 3.9L
V-6
.................................8I-2
ENGINE - IGNITION COIL RESISTANCE,
8.0L V-10
............................8I-3
ENGINE - INSTALLATION
...............9-241
ENGINE - INSTALLATION, DIESEL
........19-35
ENGINE - INSTALLATION, GASOLINE
.....19-35
ENGINE - REMOVAL
..................9-238
ENGINE - REMOVAL, DIESEL
...........19-33
ENGINE - REMOVAL, GASOLINE
.........19-33
ENGINE - SPARK PLUG CABLE ORDER,
8.0L V-10
............................8I-2
ENGINE - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM 5.9L
DIESEL
.............................7-15
ENGINE - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM 5.9L
DIESEL
.............................7-15
ENGINE - TORQUE, DIESEL
.............14-90
ENGINE - VISUAL INSPECTION, 8.0L
.....14-32
12 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page