diagram DODGE RAM 2002 Service Repair Manual

(1) The relay common feed terminal cavity (30) is
connected to fused battery feed directly from a fuse
in the Power Distribution Center (PDC), and should
be hot at all times. Check for battery voltage at the
PDC cavity for relay terminal 30. If OK, go to Step 2.
If not OK, repair the open circuit to the PDC fuse as
required.
(2) The relay normally closed terminal cavity (87A)
is not used for this application. Go to Step 3.
(3) The relay normally open terminal cavity (87) is
connected to the blower motor. When the relay is
energized, terminal 87 is connected to terminal 30
and provides full battery current to the blower motor
feed circuit. There should be continuity between the
PDC cavity for terminal 87 and the blower motor
relay output circuit cavity of the blower motor wire
harness connector at all times. If OK, go to Step 4. If
not OK, repair the open circuit to the blower motor
as required.
(4) The coil battery terminal cavity (86) is con-
nected to the ignition switch. When the ignition
switch is placed in the On position, fused ignition
switch output is directed from a fuse in the junction
block to the relay electromagnetic coil to energize the
relay. There should be battery voltage at the PDC
cavity for relay terminal 86 with the ignition switch
in the On position. If OK, go to Step 5. If not OK,
repair the open circuit to the junction block fuse as
required.
(5) The coil ground terminal cavity (85) is con-
nected to ground. This terminal supplies the ground
for the relay electromagnetic coil. There should be
continuity between the PDC cavity for relay terminal
85 and a good ground at all times. If not OK, repair
the open circuit as required.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the cover from the Power Distribution
Center (PDC) (Fig. 22).
(3) Refer to the label on the PDC for blower motor
relay identification and location.
(4) Unplug the blower motor relay from the PDC
and remove it.
INSTALLATION
(1) Install the blower motor relay by aligning the
relay terminals with the cavities in the PDC and
pushing the relay firmly into place.
(2) Install the PDC cover.
(3) Connect the battery negative cable.
(4) Test the relay operation.
BLOWER MOTOR RESISTOR
BLOCK
DESCRIPTION
The blower motor resistor is mounted to the bot-
tom of the HVAC housing, under the instrument
panel and just inboard of the blower motor. It can be
accessed without removing any other components.
OPERATION
The resistor has multiple resistor wires, each of
which will change the resistance in the blower motor
ground path to change the blower motor speed. The
blower motor switch directs the ground path through
the correct resistor wire to obtain the selected blower
motor speed.
With the blower motor switch in the lowest speed
position, the ground path for the motor is applied
through all of the resistor wires. Each higher speed
selected with the blower motor switch applies the
blower motor ground path through fewer of the resis-
tor wires, increasing the blower motor speed. When
the blower motor switch is in the highest speed posi-
tion, the blower motor resistor is bypassed and the
blower motor receives a direct path to ground.
The blower motor resistor cannot be repaired and,
if faulty or damaged, it must be replaced.
DIAGNOSIS AND TESTING - BLOWER MOTOR
RESISTOR BLOCK
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information).
Fig. 22 POWER DISTRIBUTION CENTER
1 - COVER
2 - POWER DISTRIBUTION CENTER
BR/BECONTROLS 24 - 23
BLOWER MOTOR RELAY (Continued)

DIAGNOSIS AND TESTING - BLOWER MOTOR
SWITCH
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Check for battery voltage at the fuse in the
Power Distribution Center (PDC). If OK, go to Step
2. If not OK, repair the shorted circuit or component
as required and replace the faulty fuse.
(2) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Remove the a/c heater control from the instrument
panel. (Refer to 24 - HEATING & AIR CONDITION-
ING/CONTROLS/A/C HEATER CONTROL -
REMOVAL) Check for continuity between the ground
circuit cavity of the a/c heater control wire harness
connector and a good ground. There should be conti-
nuity. If OK, go to Step 3. If not OK, repair the open
circuit to ground as required.
(3) With the a/c heater control wire harness con-
nector unplugged, place the a/c heater mode control
switch knob in any position except the Off position.
Check for continuity between the ground circuit ter-
minal and each of the blower motor driver circuit ter-
minals of the a/c heater control as you move the
blower motor switch knob to each of the four speed
positions. There should be continuity at each driver
circuit terminal in only one blower motor switch
speed position. If OK, test and repair the blower
driver circuits between the a/c heater control connec-
tor and the blower motor resistor as required. If not
OK, replace the faulty a/c heater control unit.
REMOVAL
The blower motor switch cannot be repaired and, if
faulty or damaged, the entire heater-only or a/c
heater control unit must be replaced. (Refer to 24 -
HEATING & AIR CONDITIONING/CONTROLS/A/C
HEATER CONTROL - REMOVAL) The blower motor
switch knob is serviced separately.
BLEND DOOR ACTUATOR
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Turn the ignition switch to the run position.
(2) Locate the temperature control knob in the mid
(12 o'clock) position.
(3) Turn the ignition switch to the off position.
(4) Disconnect and isolate the battery negative
cable.
(5) Remove the instrument panel from the vehi-
cle(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL ASSEMBLY - REMOVAL).
(6) Remove the HVAC housing from the vehicle.
(Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION/HVAC HOUSING - REMOVAL)
(7) Unplug the wire harness connector from the
blend door actuator (Fig. 24).
(8) Remove the two mounting screws which secure
the actuator to the housing.
(9) Slide the blend door actuator off the blend door
shaft.
NOTE: A black plastic coupler may be attached to
the blend door shaft. Remove the coupler and
inspect for damage. Reinstall if there is no damage
found.
INSTALLATION
NOTE: Before installing the blend door actuator, be
certain that the blend door is not binding and is
capable of full travel in both directions.
(1) Align the actuator with the blend door shaft
and rotate the actuator to align it to the mounting
bosses on the HVAC housing.
(2) Align and install the actuator screws. Tighten
the mounting screws to 2.2 N´m (20 in. lbs.).
(3) Plug in the wire harness connector to the blend
door actuator.
BR/BECONTROLS 24 - 25
BLOWER MOTOR SWITCH (Continued)

DIAGNOSIS AND TESTING - BLOWER MOTOR
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). Possible causes of
an inoperative blower motor include:
²Faulty fuse
²Faulty blower motor circuit wiring or wire har-
ness connectors
²Faulty blower motor resistor
²Faulty blower motor relay
²Faulty blower motor switch
²Faulty a/c heater mode control switch
²Faulty blower motor.
Possible causes of the blower motor not operating
in all speeds include:
²Faulty fuse
²Faulty blower motor switch
²Faulty blower motor resistor
²Faulty blower motor relay
²Faulty blower motor circuit wiring or wire har-
ness connectors.
VIBRATION
Possible causes of blower motor vibration include:
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower wheel out of balance or deformed
²Blower motor faulty.
NOISE
To verify that the blower is the source of the noise,
unplug the blower motor wire harness connector and
operate the HVAC system. If the noise goes away,
possible causes include:
²Foreign material in the HVAC housing
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower motor faulty.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Disconnect the blower motor cooling tube from
the nipple on the blower motor housing (Fig. 3).
(3) Disengage the blower motor wire harness from
the wire harness retainer.
(4) Unplug the blower motor wire harness connec-
tor from the HVAC housing wire harness.
(5) Remove the three screws that secure the
blower motor and blower wheel assembly to the
HVAC housing.
(6) Lower the blower motor and wheel assembly,
and cover, from the HVAC housing.
(7) Remove the blower wheel retainer clip and
remove the wheel from the blower motor shaft (Fig.
4).
INSTALLATION
(1) If installing the blower motor wheel only, press
the blower wheel hub onto the blower motor shaft.
Be sure the flat on the blower motor shaft is indexed
to the flat on the inside of the blower wheel hub.
(2) Install the retainer clip over the blower wheel
hub. The ears of the retainer clip must be indexed
over the flats on the blower motor shaft and blower
wheel hub.
Fig. 3 BLOWER MOTOR REMOVE/INSTALL
1 - BLOWER MOTOR HOUSING
2 - COOLING TUBE
3 - ELECTRICAL CONNECTOR
24 - 32 DISTRIBUTIONBR/BE
BLOWER MOTOR (Continued)

CRANKSHAFT MAIN BEARINGS -
DESCRIPTION........................9-31
CRANKSHAFT MAIN BEARINGS -
INSTALLATION....................9-32,9-88
CRANKSHAFT MAIN BEARINGS -
OPERATION..........................9-31
CRANKSHAFT MAIN BEARINGS -
REMOVAL.......................9-31,9-88
CRANKSHAFT MAIN BEARINGS -
STANDARD PROCEDURE, FITTING........9-88
CRANKSHAFT OIL SEAL - FRONT -
DESCRIPTION........................9-32
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION...................9-160,9-32
CRANKSHAFT OIL SEAL - FRONT -
OPERATION..........................9-32
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL......................9-160,9-32
CRANKSHAFT OIL SEAL - REAR -
DESCRIPTION........................9-33
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION...............9-162,9-34,9-90
CRANKSHAFT OIL SEAL - REAR -
OPERATION..........................9-33
CRANKSHAFT OIL SEAL - REAR -
REMOVAL..................9-161,9-33,9-90
CRANKSHAFT REAR OIL SEAL RETAINER
- INSTALLATION.................9-163,9-90
CRANKSHAFT REAR OIL SEAL RETAINER
- REMOVAL.....................9-162,9-90
CROSSHEADS - CLEANING.............9-134
CROSSHEADS - INSPECTION...........9-135
CRUISE INDICATOR - DESCRIPTION.......8J-18
CRUISE INDICATOR - OPERATION.......8J-18
CUBBY BIN - INSTALLATION...........23-109
CUBBY BIN - REMOVAL..............23-108
CUP HOLDER - INSTALLATION.........23-110
CUP HOLDER - REMOVAL.............23-109
CUSHION - INSTALLATION, SEAT.......23-138
CUSHION - REMOVAL, SEAT...........23-138
CUSHION COVER - INSTALLATION, SEAT . 23-139
CUSHION COVER - REMOVAL, SEAT.....23-139
CUSHION COVER - SPLIT BENCH -
INSTALLATION, SEAT.................23-140
CUSHION COVER - SPLIT BENCH -
REMOVAL, SEAT....................23-139
CYLINDER - DESCRIPTION, MASTER......5-26
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK........19-9
CYLINDER - INSTALLATION, LOCK.......23-74
CYLINDER - INSTALLATION, LOCK.......19-10
CYLINDER - INSTALLATION, MASTER.....5-28
CYLINDER - OPERATION, MASTER........5-26
CYLINDER - REMOVAL, LOCK...........23-74
CYLINDER - REMOVAL, LOCK...........19-10
CYLINDER - REMOVAL, MASTER.........5-27
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-27
CYLINDER BLOCK REFACING -
STANDARD PROCEDURE...............9-148
CYLINDER BORE - DE-GLAZE -
STANDARD PROCEDURE...............9-148
CYLINDER BORE HONING - STANDARD
PROCEDURE.....................9-11,9-65
CYLINDER BORE REPAIR - STANDARD
PROCEDURE........................9-149
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING
. . 9-64,9-9
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING
...........9-64,9-9
CYLINDER HEAD - CLEANING
.......9-134,9-77
CYLINDER HEAD - DESCRIPTION
. . . 9-130,9-20,
9-76
CYLINDER HEAD - INSPECTION
.....9-134,9-77
CYLINDER HEAD - INSTALLATION
........9-77
CYLINDER HEAD - OPERATION
...........9-21
CYLINDER HEAD - REMOVAL
.......9-130,9-76
CYLINDER HEAD COVER GASKET -
DESCRIPTION
........................9-20
CYLINDER HEAD COVER GASKET -
OPERATION
..........................9-21
CYLINDER HEAD COVER(S) - CLEANING
. . 9-137,
9-23,9-79
CYLINDER HEAD COVER(S) -
DESCRIPTION
........................9-78
CYLINDER HEAD COVER(S) -
INSPECTION
................9-138,9-23,9-79CYLINDER HEAD COVER(S) -
INSTALLATION...............9-138,9-23,9-79
CYLINDER HEAD COVER(S) - REMOVAL . . 9-137,
9-23,9-78
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING..........9-21,9-76
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR..................8N-5
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-6
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR.................8N-6
CYLINDER LOCK SWITCH - OPERATION,
DOOR..............................8N-5
CYLINDER LOCK SWITCH - REMOVAL,
DOOR..............................8N-6
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-26
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-2
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE,
REPAIR ....................9-11,9-122,9-66
DAMPER - INSPECTION, VIBRATION.....9-172
DAMPER - INSTALLATION,
VIBRATION.................9-173,9-40,9-97
DAMPER - REMOVAL, VIBRATION . . . 9-172,9-40,
9-96
DANA 44 & 60 - REMOVAL..............2-19
DANA 44 AXLE - INSTALLATION......2-20,2-21
DANA 44 AXLE - REMOVAL.............2-21
DANA 60 AXLE - INSTALLATION.......2-20,2-22
DANA 60 AXLE - REMOVAL.............2-21
DATA BUS - DESCRIPTION, CCD..........8E-6
DATA BUS - DIAGNOSIS AND TESTING,
CCD ...............................8E-11
DATA BUS - OPERATION, CCD...........8E-7
DATA LINK CONNECTOR - DESCRIPTION . . 8E-12
DATA LINK CONNECTOR - OPERATION....8E-12
DATA PLATE - DESCRIPTION, ENGINE....9-129
DATA PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP....................14-77
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC........................8N-11
DAY / NIGHT MIRROR - INSTALLATION,
AUTOMATIC........................8N-13
DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-12
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-13
DAY/NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-12
DAYTIME RUNNING LAMP MODULE -
DESCRIPTION........................8L-9
DAYTIME RUNNING LAMP MODULE -
INSTALLATION........................8L-9
DAYTIME RUNNING LAMP MODULE -
OPERATION..........................8L-9
DAYTIME RUNNING LAMP MODULE -
REMOVAL...........................8L-9
DECALS - INSTALLATION..............23-64
DECALS - INSTALLATION, BODY
STRIPES...........................23-87
DECALS - REMOVAL..................23-64
DECALS - REMOVAL, BODY STRIPES
.....23-87
DEFINITION - DESCRIPTION, TRIP
.......25-19
DEFROSTER AND DEMISTER DUCT
ADAPTER - INSTALLATION
.............24-33
DEFROSTER AND DEMISTER DUCT
ADAPTER - REMOVAL
.................24-33
DEFROSTER AND DEMISTER DUCTS -
INSTALLATION
.......................24-33
DEFROSTER AND DEMISTER DUCTS -
REMOVAL
..........................24-33
DE-GLAZE - STANDARD PROCEDURE,
CYLINDER BORE
.....................9-148
DELIVERY - SPECIFICATIONS, TORQUE -
FUEL
...............................14-4
DELIVERY SYSTEM - DESCRIPTION,
DIESEL FUEL
........................14-55
DELIVERY SYSTEM - DESCRIPTION,
FUEL
...............................14-2
DELIVERY SYSTEM - OPERATION, FUEL
. . . 14-2
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS
...............8M-5
DEMISTER DUCT ADAPTER -
INSTALLATION, DEFROSTER
............24-33DEMISTER DUCT ADAPTER - REMOVAL,
DEFROSTER.........................24-33
DEMISTER DUCTS - INSTALLATION,
DEFROSTER.........................24-33
DEMISTER DUCTS - INSTALLATION,
INSTRUMENT PANEL..................24-36
DEMISTER DUCTS - REMOVAL,
DEFROSTER.........................24-33
DEMISTER DUCTS - REMOVAL,
INSTRUMENT PANEL..................24-36
DEMISTER GRILLES - INSTALLATION.....24-31
DEMISTER GRILLES - REMOVAL........24-31
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN
AIRBAG.............................8O-4
DETECTION PUMP - DESCRIPTION, LEAK . 25-34
DETECTION PUMP - INSTALLATION,
LEAK..............................25-34
DETECTION PUMP - OPERATION, LEAK . . . 25-34
DETECTION PUMP - REMOVAL, LEAK....25-34
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING......................8W-01-1
DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS.................21-132,21-302
DIESEL - CLEANING, RADIATOR - 5.9L....7-64
DIESEL - CLEANING, RADIATOR FAN -
5.9L................................7-43
DIESEL - CLEANING, WATER PUMP -
5.9L................................7-72
DIESEL - DESCRIPTION................25-1
DIESEL - DESCRIPTION........14-106,14-108
DIESEL - DESCRIPTION.................8I-6
DIESEL - DESCRIPTION, 5.9L............11-3
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - DESCRIPTION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-40
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-2
DIESEL - DESCRIPTION, ENGINE 5.9L....9-115
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-46
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-53
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-56
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-62
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-84
DIESEL - DESCRIPTION, VACUUM PUMP
- 5.9L..............................7-33
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-72
DIESEL - FUEL INJECTOR FIRING ORDER . 14-62
DIESEL - INSPECTION, EXHAUST PIPE -
5.9L................................11-9
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-64
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-43
DIESEL - INSPECTION, TAILPIPE - 5.9L . . . 11-12
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-72
DIESEL - INSTALLATION..............14-107
DIESEL - INSTALLATION................8I-9
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - INSTALLATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-32
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-46
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-54
DIESEL - INSTALLATION, EXHAUST PIPE
- 5.9L..............................11-9
DIESEL - INSTALLATION, MUFFLER -
5.9L
...............................11-11
DIESEL - INSTALLATION, RADIATOR -
5.9L
................................7-64
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L
..............................7-44
DIESEL - INSTALLATION, TAILPIPE - 5.9L
. 11-13
DIESEL - INSTALLATION, VACUUM
PUMP - 5.9L
.........................7-36
BR/BEINDEX 9
Description Group-Page Description Group-Page Description Group-Page

HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-78
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-78
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-47
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-20
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-20
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-78
HINGE - INSTALLATION.....23-100,23-72,23-80
HINGE - REMOVAL........23-100,23-72,23-79
HITCH - INSTALLATION, TRAILER.........13-11
HITCH - REMOVAL, TRAILER...........13-11
HOISTING - STANDARD PROCEDURE.......0-9
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDER - INSTALLATION, CUP........23-110
HOLDER - REMOVAL, CUP............23-109
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE..................9-11,9-65
HOOD - INSTALLATION...............23-101
HOOD - REMOVAL...................23-101
HOOK - INSTALLATION, COAT..........23-125
HOOK - INSTALLATION, FRONT TOW.....13-10
HOOK - REMOVAL, COAT.............23-124
HOOK - REMOVAL, FRONT TOW.........13-10
HORN - DESCRIPTION.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - OPERATION...............8H-1,8H-2
HORN - REMOVAL....................8H-2
HORN RELAY - DESCRIPTION.......8W-97-12
HORN RELAY - DESCRIPTION...........8H-3
HORN RELAY - DIAGNOSIS AND
TESTING........................8W-97-12
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION.......8W-97-12
HORN RELAY - INSTALLATION...........8H-4
HORN RELAY - OPERATION.............8H-3
HORN RELAY - REMOVAL..........8W-97-12
HORN RELAY - REMOVAL..............8H-4
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HORN SWITCH - REMOVAL.............8H-5
HOSE CLAMPS - DESCRIPTION...........7-4
HOSE CLAMPS - OPERATION.............7-4
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-76
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-73
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-76
HOSES - PRESSURE - DESCRIPTION
.....19-39
HOSES - PRESSURE - OPERATION
.......19-39
HOSES - RETURN - DESCRIPTION
.......19-39
HOSES - RETURN - OPERATION
.........19-39
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-43HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-9
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH......6-11
HOUSING - INSTALLATION, GEAR........9-188
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - REMOVAL, CLUTCH..........6-11
HOUSING - REMOVAL, GEAR...........9-187
HOUSING - REMOVAL, HVAC...........24-34
HOUSING BUSHING - INSTALLATION,
EXTENSION..................21-156,21-326
HOUSING BUSHING - REMOVAL,
EXTENSION..................21-156,21-326
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-460,21-497
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-460,21-497
HOUSING COVER - INSTALLATION, GEAR . 9-190
HOUSING COVER - REMOVAL, GEAR.....9-189
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-101,21-273
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-36
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-35
HOUSING PLUG - INSTALLATION,
STEERING GEAR.......................19-30
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-29
HOUSING SEAL - INSTALLATION,
EXTENSION..................21-156,21-327
HOUSING SEAL - NV4500 -
INSTALLATION, ADAPTER..............21-42
HOUSING SEAL - NV4500 -
INSTALLATION, EXTENSION............21-42
HOUSING SEAL - NV4500 - REMOVAL,
ADAPTER...........................21-42
HOUSING SEAL - NV4500 - REMOVAL,
EXTENSION.........................21-42
HOUSING SEAL - NV5600 -
INSTALLATION, ADAPTER..............21-85
HOUSING SEAL - NV5600 -
INSTALLATION, EXTENSION............21-85
HOUSING SEAL - NV5600 - REMOVAL,
ADAPTER...........................21-85
HOUSING SEAL - NV5600 - REMOVAL,
EXTENSION.........................21-85
HOUSING SEAL - REMOVAL,
EXTENSION..................21-156,21-326
HUB / BEARING - INSTALLATION......2-17,2-9
HUB / BEARING - REMOVAL..........2-16,2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HVAC HOUSING INLET BAFFLE -
INSTALLATION.......................24-36
HVAC HOUSING INLET BAFFLE -
REMOVAL..........................24-35
HVAC SYSTEM AIRFLOW - DESCRIPTION . 24-30
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-18
HYDRAULIC LIFTERS - CLEANING
....9-37,9-92
HYDRAULIC LIFTERS - INSTALLATION
. 9-37,9-92
HYDRAULIC LIFTERS - REMOVAL
....9-37,9-92
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING
.......21-270,21-98
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS
..............21-132,21-302
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING
........................9-36,9-91
HYDRAULIC/MECHANICAL -
DESCRIPTION
.........................5-4
HYDRAULIC/MECHANICAL - WARNING
.....5-4
HYDROMETER TEST - STANDARD
PROCEDURE
........................8F-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
................9-11,9-122,9-66
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD
.........................8L-29IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT.......................Intro.-3
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-40
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-40
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 5.9L
ENGINES............................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-4
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING....19-9
IGNITION TIMING, SPECIFICATIONS.......8I-4
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-15
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-20
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-27
INDICATOR - DESCRIPTION, TRANS
OVERTEMP.........................8J-31
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATOR - DESCRIPTION, UPSHIFT....8J-32
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-21
INDICATOR - DIAGNOSIS AND TESTING,
TURN SIGNAL
.......................8J-32
INDICATOR - DIAGNOSIS AND TESTING,
VTSS
...............................8Q-4
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID
......................8J-35
INDICATOR - OPERATION, ABS
..........8J-14
INDICATOR - OPERATION, AIRBAG
.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-15
INDICATOR - OPERATION, CHECK
GAUGES
............................8J-17
INDICATOR - OPERATION, CRUISE
.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR
..........................8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-21
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, SEATBELT
.....8J-27
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

REMOTE KEYLESS ENTRY SYSTEM -
DESCRIPTION........................8N-2
REMOTE KEYLESS ENTRY SYSTEM -
DIAGNOSIS AND TESTING, POWER
LOCK...............................8N-5
REMOTE KEYLESS ENTRY SYSTEM -
OPERATION..........................8N-4
REMOTE KEYLESS ENTRY
TRANSMITTER - DESCRIPTION..........8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - OPERATION............8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
REMOTE SWITCHES - DESCRIPTION.....8A-14
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-15
REMOTE SWITCHES - INSTALLATION.....8A-16
REMOTE SWITCHES - OPERATION.......8A-15
REMOTE SWITCHES - REMOVAL........8A-16
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD...........21-114,21-286
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-151
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-149
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE.....9-11,9-122,9-66
REPAIRING LEAKS - STANDARD
PROCEDURE.........................22-9
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-3
REQUIREMENTS - GAS ENGINES -
DESCRIPTION, FUEL....................0-2
RESERVOIR - DESCRIPTION, VACUUM . . . 8P-14
RESERVOIR - DESCRIPTION, WASHER . . . 8R-10
RESERVOIR - INSTALLATION, FLUID......5-15
RESERVOIR - INSTALLATION, VACUUM . . . 8P-15
RESERVOIR - INSTALLATION, WASHER . . . 8R-11
RESERVOIR - OPERATION, WASHER.....8R-10
RESERVOIR - REMOVAL, FLUID..........5-15
RESERVOIR - REMOVAL, VACUUM.......8P-14
RESERVOIR - REMOVAL, WASHER......8R-10
RESISTANCE, 5.9L ENGINES - IGNITION
COIL................................8I-3
RESISTANCE, 8.0L V-10 ENGINE -
IGNITION COIL........................8I-4
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-3
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-23
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR............24-23
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR....................24-24
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR....................24-23
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR............................24-24
RESONATOR - INSTALLATION...........11-13
RESONATOR - REMOVAL..............11-13
RESTRAINTS - DESCRIPTION............8O-1
RESTRAINTS - OPERATION.............8O-2
RESTRAINTS - WARNING...............8O-3
RESTRICTIONS - DIAGNOSIS AND
TESTING, FUEL SUPPLY...............14-60
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON.....21-193,
21-364
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-192,
21-364
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
...........21-192,21-363
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
...........21-192,21-364
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
...........21-193,21-364
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL
......9-163,9-90RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON.....21-192,
21-363
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL..................9-162,9-90
RETRACTOR - INSTALLATION, REAR
SEAT BELT .........................8O-26
RETRACTOR - REMOVAL, REAR SEAT
BELT ..............................8O-26
RETURN - DESCRIPTION, HOSES........19-39
RETURN - DESCRIPTION, SENSOR.......8E-17
RETURN - OPERATION, HOSES..........19-39
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE................22-9
RIGHT FRONT FENDER - INSTALLATION . . 23-94
RIGHT FRONT FENDER - REMOVAL......23-94
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE......3-104,3-132,3-75
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE................3-103,3-131,3-73
RING FITTING - STANDARD
PROCEDURE, PISTON.............9-171,9-39
RINGS - STANDARD PROCEDURE,
FITTING PISTON......................9-95
RISER - INSTALLATION, SEAT..........23-141
RISER - REMOVAL, SEAT.............23-141
RKE TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-8
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-4
ROAD TESTING - DIAGNOSIS AND
TESTING.....................21-269,21-97
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION........................9-26
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL...........................9-26
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-146
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-145
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-146
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION...................9-148,9-84
ROCKER ARM / ADJUSTER ASSY -
REMOVAL......................9-145,9-84
ROD - CLEANING, PISTON &
CONNECTING...............9-169,9-39,9-94
ROD - DESCRIPTION, PISTON &
CONNECTING...............9-165,9-38,9-93
ROD - INSPECTION, PISTON &
CONNECTING.....................9-39,9-94
ROD - INSTALLATION, PISTON &
CONNECTING.....................9-39,9-94
ROD - REMOVAL, PISTON &
CONNECTING...............9-168,9-38,9-94
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING............9-158
ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING.........9-29,9-87
RODS, INSPECTION - CONNECTING......9-169
ROOF JOINT MOLDING - INSTALLATION . . 23-91
ROOF JOINT MOLDING - REMOVAL......23-91
ROTATION - STANDARD PROCEDURE,
TIRE
................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISTRIBUTOR
.......................8I-14
ROTOR, DIAGNOSIS AND TESTING -
DISC BRAKE
.........................5-20
RUN CHANNEL - INSTALLATION, GLASS
. . 23-71
RUN CHANNEL - REMOVAL, GLASS
......23-71
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS
................23-153
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS
................23-152
RUNNING LAMP MODULE -
DESCRIPTION, DAYTIME
................8L-9
RUNNING LAMP MODULE -
INSTALLATION, DAYTIME
...............8L-9
RUNNING LAMP MODULE - OPERATION,
DAYTIME
............................8L-9
RUNNING LAMP MODULE - REMOVAL,
DAYTIME
............................8L-9
RUNOUT - DIAGNOSIS AND TESTING,
TIRE AND WHEEL
.....................22-1
RWAL SERVICE PRECAUTIONS -
STANDARD PROCEDURE
................5-36SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-1
SAFETY LATCH - INSTALLATION........23-104
SAFETY LATCH - REMOVAL...........23-104
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SANDING/BUFFING & POLISHING -
DESCRIPTION, WET.................23-130
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-7
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS.......21-132,21-302
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC.......21-132,21-302
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER NECK.........7-65
SEAL - FRONT - DESCRIPTION,
CRANKSHAFT OIL.....................9-32
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL................9-160,9-32
SEAL - FRONT - OPERATION,
CRANKSHAFT OIL.....................9-32
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL................9-160,9-32
SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL..............9-89
SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT OIL.................9-89
SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT OIL..............9-90
SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT OIL.................9-89
SEAL - INSTALLATION, B-PILLAR DOOR . . . 23-151
SEAL - INSTALLATION, DOOR OPENING . . 23-152
SEAL - INSTALLATION, EXTENSION
HOUSING....................21-156,21-327
SEAL - INSTALLATION, EXTENSION
HOUSING BUSHING............21-460,21-497
SEAL - INSTALLATION, FRONT DOOR
UPPER CORNER....................23-154
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT......................21-461,21-498
SEAL - INSTALLATION, PINION . 3-124,3-35,3-63,
3-95
SEAL - INSTALLATION, PITMAN SHAFT . . . 19-26
SEAL - INSTALLATION, VALVE STEM......9-83
SEAL - NV4500 - INSTALLATION,
ADAPTER HOUSING..................21-42
SEAL - NV4500 - INSTALLATION,
EXTENSION HOUSING.................21-42
SEAL - NV4500 - REMOVAL, ADAPTER
HOUSING...........................21-42
SEAL - NV4500 - REMOVAL, EXTENSION
HOUSING...........................21-42
SEAL - NV5600 - INSTALLATION,
ADAPTER HOUSING..................21-85
SEAL - NV5600 - INSTALLATION,
EXTENSION HOUSING.................21-85
SEAL - NV5600 - REMOVAL, ADAPTER
HOUSING...........................21-85
SEAL - NV5600 - REMOVAL, EXTENSION
HOUSING...........................21-85
SEAL - REAR - DESCRIPTION,
CRANKSHAFT OIL.....................9-33
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL............9-162,9-34,9-90
SEAL - REAR - OPERATION,
CRANKSHAFT OIL.....................9-33
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL .......................9-161,9-33,9-90
SEAL - REMOVAL, B-PILLAR DOOR.....23-151
SEAL - REMOVAL, DOOR OPENING.....23-152
SEAL - REMOVAL, EXTENSION
HOUSING....................21-156,21-326
SEAL - REMOVAL, EXTENSION HOUSING
BUSHING....................21-460,21-497
SEAL - REMOVAL, FRONT DOOR UPPER
CORNER..........................23-153
SEAL - REMOVAL, FRONT OUTPUT
SHAFT......................21-461,21-498
SEAL - REMOVAL, PINION
. 3-123,3-35,3-63,3-94
SEAL - REMOVAL, PITMAN SHAFT
.......19-25
SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL
...........9-163,9-90
SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR OIL
...........9-162,9-90
SEALER LOCATIONS, SPECIFICATIONS -
BODY
..............................23-47
26 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

TRANSMITTER BATTERIES - STANDARD
PROCEDURE, REMOTE KEYLESS
ENTRY..............................8N-8
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, RKE...........8N-8
TRAY - DESCRIPTION, BATTERY.........8F-23
TRAY - INSTALLATION, BATTERY........8F-24
TRAY - INSTALLATION, REAR FLOOR
STOWAGE.........................23-121
TRAY - OPERATION, BATTERY..........8F-23
TRAY - REMOVAL, BATTERY............8F-23
TRAY - REMOVAL, REAR FLOOR
STOWAGE.........................23-121
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, A-PILLAR.......23-119
TRIM - INSTALLATION, B-PILLAR.......23-120
TRIM - INSTALLATION, C-PILLAR.......23-128
TRIM - INSTALLATION, DOOR SILL.....23-121
TRIM - INSTALLATION, GLOVE BOX
OPENING UPPER....................23-112
TRIM - INSTALLATION, REAR CLOSURE
PANEL............................23-121
TRIM - REMOVAL, A-PILLAR..........23-119
TRIM - REMOVAL, B-PILLAR..........23-120
TRIM - REMOVAL, C-PILLAR..........23-128
TRIM - REMOVAL, DOOR SILL.........23-121
TRIM - REMOVAL, GLOVE BOX OPENING
UPPER............................23-112
TRIM - REMOVAL, REAR CLOSURE
PANEL............................23-120
TRIM COVER - INSTALLATION, COWL . . . 23-120
TRIM COVER - REMOVAL, COWL.......23-119
TRIM PANEL - INSTALLATION......23-75,23-84
TRIM PANEL - INSTALLATION, QUARTER . 23-128
TRIM PANEL - REMOVAL.........23-75,23-83
TRIM PANEL - REMOVAL, QUARTER....23-128
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-54
TUBE - DIAGNOSIS AND TESTING, FIXED
ORIFICE............................24-54
TUBE - INSTALLATION, A/C ORIFICE......24-54
TUBE - OPERATION, A/C ORIFICE........24-54
TUBE - REMOVAL, A/C ORIFICE.........24-54
TUBES - WITH RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS...................7-78,7-82,7-84
TUBES - WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS...................7-79,7-82,7-85
TURBOCHARGER - CLEANING..........11-16
TURBOCHARGER - DESCRIPTION........11-14
TURBOCHARGER - INSPECTION.........11-16
TURBOCHARGER - INSTALLATION.......11-17
TURBOCHARGER - OPERATION.........11-14
TURBOCHARGER - REMOVAL...........11-15
TURBOCHARGER BOOST PRESSURE -
DIAGNOSIS AND TESTING.............11-13
TURN SIGNAL & HAZARD WARNING
SYSTEM - DESCRIPTION
...............8L-2
TURN SIGNAL & HAZARD WARNING
SYSTEM - DIAGNOSIS AND TESTING
......8L-3
TURN SIGNAL & HAZARD WARNING
SYSTEM - OPERATION
.................8L-2
TURN SIGNAL CANCEL CAM -
DESCRIPTION
.......................8L-31
TURN SIGNAL CANCEL CAM -
OPERATION
.........................8L-31
TURN SIGNAL INDICATOR -
DESCRIPTION
.......................8J-32
TURN SIGNAL INDICATOR - DIAGNOSIS
AND TESTING
.......................8J-32
TURN SIGNAL INDICATOR - OPERATION
. . 8J-32
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT
.............8O-29
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT
.........................8O-29
TURNING LOOP HGT ADJUSTER KNOB -
INSTALLATION
......................8O-30
TURNING LOOP HGT ADJUSTER KNOB -
REMOVAL
..........................8O-30
TWEETER SPEAKER - INSTALLATION,
A-PILLAR
...........................8A-19TWEETER SPEAKER - REMOVAL,
A-PILLAR...........................8A-18
UNDERHOOD LAMP - INSTALLATION.....8L-32
UNDERHOOD LAMP - REMOVAL.........8L-31
UNDERHOOD LAMP UNIT -
INSTALLATION.......................8L-32
UNDERHOOD LAMP UNIT - REMOVAL....8L-32
UNIVERSAL JOINTS - ASSEMBLY,
DOUBLE CARDAN.....................3-11
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
DOUBLE CARDAN.....................3-10
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL JOINTS - INSTALLATION,
SINGLE CARDAN......................3-35
UNIVERSAL JOINTS - REMOVAL, SINGLE
CARDAN............................3-34
UP/DOWN - ADJUSTMENT, FRONT DOOR . 23-70
UPPER - INSTALLATION, LATCH.........23-81
UPPER - INSTALLATION, LATCH
STRIKER...........................23-82
UPPER - REMOVAL, LATCH............23-81
UPPER - REMOVAL, LATCH STRIKER.....23-82
UPPER BALL JOINT - DIAGNOSIS AND
TESTING............................2-12
UPPER CONTROL ARM - INSTALLATION . . . 2-13,
2-19
UPPER CONTROL ARM - REMOVAL . . . 2-13,2-19
UPSHIFT INDICATOR - DESCRIPTION......8J-32
UPSHIFT INDICATOR - OPERATION.......8J-33
USAGE - DESCRIPTION, FASTENER.....Intro.-9
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-10 - DESCRIPTION, 8.0L..............8I-2
V-10 - OPERATION, 8.0L................8I-2
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-4
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-3
V-8 - OPERATION......................8I-2
V-8 ENGINES - DESCRIPTION...........25-35
V-8 ENGINES - ENGINE FIRING ORDER,
5.9L................................8I-3
V-8 ENGINES - OPERATION............25-35
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-29
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-29
VACUUM LINES - DESCRIPTION.........25-37
VACUUM MOTOR - ASSEMBLY, AXLE......3-34
VACUUM MOTOR - DESCRIPTION, AXLE . . . 3-31
VACUUM MOTOR - DIAGNOSIS AND
TESTING............................3-32
VACUUM MOTOR - DISASSEMBLY, AXLE . . . 3-34
VACUUM MOTOR - INSTALLATION, AXLE . . . 3-34
VACUUM MOTOR - OPERATION, AXLE.....3-31
VACUUM MOTOR - REMOVAL, AXLE......3-34
VACUUM PUMP - 5.9L DIESEL -
DESCRIPTION........................7-33
VACUUM PUMP - 5.9L DIESEL -
INSTALLATION........................7-36
VACUUM PUMP - 5.9L DIESEL -
OPERATION
..........................7-34
VACUUM PUMP - 5.9L DIESEL -
REMOVAL
...........................7-34
VACUUM PUMP OUTPUT - DIAGNOSIS
AND TESTING
........................7-34
VACUUM RESERVOIR - DESCRIPTION
....8P-14
VACUUM RESERVOIR - INSTALLATION
. . . 8P-15
VACUUM RESERVOIR - REMOVAL
.......8P-14
VACUUM SUPPLY TEST - DIAGNOSIS
AND TESTING
........................8P-3
VACUUM SYSTEM - DIAGNOSIS AND
TESTING
...........................24-10
VACUUM TEST - DIAGNOSIS AND
TESTING, FUEL SYSTEM AIR LEAK
.......14-57
VALVE - 5.9L - DIAGNOSIS AND
TESTING, PCV
.......................25-36
VALVE - CLEANING, OIL PRESSURE
RELIEF
.............................9-180
VALVE - DESCRIPTION, COMBINATION
......5-8
VALVE - DESCRIPTION, FUEL TANK
CHECK
.............................14-21VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-46
VALVE - DESCRIPTION, ONE WAY CHECK . 25-31
VALVE - DESCRIPTION, OVERFLOW......14-87
VALVE - DESCRIPTION, TORQUE
CONVERTER DRAINBACK.......21-217,21-390
VALVE - DESCRIPTION, VACUUM CHECK . . 24-28
VALVE - DIAGNOSIS AND TESTING,
COMBINATION.........................5-9
VALVE - DIAGNOSIS AND TESTING,
ONE-WAY CHECK.....................25-31
VALVE - DIAGNOSIS AND TESTING,
OVERFLOW.........................14-87
VALVE - INSPECTION, OIL PRESSURE
RELIEF.............................9-180
VALVE - INSTALLATION, COMBINATION.....5-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-23
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-180
VALVE - INSTALLATION, ONE WAY
CHECK.............................25-31
VALVE - INSTALLATION, OVERFLOW.....14-88
VALVE - INSTALLATION, SPOOL.........19-28
VALVE - INSTALLATION, VACUUM CHECK . 24-29
VALVE - OPERATION, COMBINATION.......5-9
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-47
VALVE - OPERATION, ONE WAY CHECK . . . 25-31
VALVE - OPERATION, OVERFLOW........14-87
VALVE - OPERATION, TORQUE
CONVERTER DRAINBACK.......21-217,21-390
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, COMBINATION.........5-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-22
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-180
VALVE - REMOVAL, ONE WAY CHECK....25-31
VALVE - REMOVAL, OVERFLOW.........14-88
VALVE - REMOVAL, SPOOL.............19-26
VALVE - REMOVAL, VACUUM CHECK.....24-29
VALVE - STANDARD PROCEDURE,
TORQUE CONVERTER DRAINBACK.....21-217,
21-390
VALVE BODY - ADJUSTMENTS . . . 21-257,21-428
VALVE BODY - ASSEMBLY......21-248,21-420
VALVE BODY - CLEANING.......21-244,21-418
VALVE BODY - DESCRIPTION....21-218,21-391
VALVE BODY - DISASSEMBLY....21-237,21-409
VALVE BODY - INSPECTION.....21-244,21-419
VALVE BODY - INSTALLATION....21-256,21-428
VALVE BODY - OPERATION......21-223,21-394
VALVE BODY - REMOVAL.......21-236,21-407
VALVE CABLE - ADJUSTMENTS,
TRANSMISSION THROTTLE.....21-210,21-382
VALVE CABLE - DESCRIPTION,
THROTTLE...................21-209,21-381
VALVE LASH ADJUSTMENT AND
VERIFICATION - STANDARD
PROCEDURE........................9-141
VALVE SERVICE, STANDARD
PROCEDURE.........................9-80
VALVE SPRINGS - INSTALLATION,
VALVES .............................9-84
VALVE SPRINGS - REMOVAL, VALVES.....9-82
VALVE STEM SEAL - INSTALLATION.......9-83
VALVE STEM SEALS - REMOVAL.........9-82
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST............9-138,9-23,9-80
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.....................9-25
VALVES AND VALVE SPRINGS -
INSTALLATION........................9-84
VALVES AND VALVE SPRINGS -
REMOVAL...........................9-82
VALVES, GUIDES AND SPRINGS -
STANDARD PROCEDURE
................9-23
VALVES,GUIDES AND SPRINGS -
STANDARD PROCEDURE
...............9-138
VANITY LAMP - INSTALLATION
.........8L-37
VANITY LAMP - REMOVAL
.............8L-37
VAPOR CANISTER - DESCRIPTION
.......25-37
BR/BEINDEX 33
Description Group-Page Description Group-Page Description Group-Page

WINDOW SWITCH - REMOVAL, POWER . . 8N-25
WINDOWS - DESCRIPTION, POWER.....8N-23
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-23
WINDOWS - OPERATION, POWER.......8N-23
WINDSHIELD - DESCRIPTION..........23-147
WINDSHIELD - INSTALLATION.........23-148
WINDSHIELD - REMOVAL.............23-147
WIPER & WASHER SYSTEM - CLEANING . . 8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-3
WIPER & WASHER SYSTEM -
INSPECTION.........................8R-6
WIPER ARM - DESCRIPTION...........8R-11
WIPER ARM - INSTALLATION...........8R-12
WIPER ARM - OPERATION.............8R-11
WIPER ARM - REMOVAL..............8R-12
WIPER BLADE - DESCRIPTION..........8R-12
WIPER BLADE - INSTALLATION.........8R-13WIPER BLADE - OPERATION...........8R-13
WIPER BLADE - REMOVAL.............8R-13
WIPER MODULE - DESCRIPTION........8R-13
WIPER MODULE - INSTALLATION.......8R-14
WIPER MODULE - OPERATION..........8R-14
WIPER MODULE - REMOVAL...........8R-14
WIPER RELAY - DESCRIPTION..........8R-15
WIPER RELAY - DIAGNOSIS AND
TESTING
...........................8R-16
WIPER RELAY - INSTALLATION
.........8R-17
WIPER RELAY - OPERATION
...........8R-15
WIPER RELAY - REMOVAL
.............8R-17
WIPERS/WASHERS - DESCRIPTION
.......8R-1
WIPERS/WASHERS - OPERATION
........8R-2
WIRE SPLICING - STANDARD
PROCEDURE
.....................8W-01-13
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE
.....................8W-01-1WIRING HARNESS - DIAGNOSIS AND
TESTING.........................8W-01-7
WIRING/TERMINAL, SPECIAL TOOLS . . . 8W-01-9
WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS
HOSE...............................7-77
WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS
HOSE...............................7-76
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES.........7-79,7-82,7-85
WORM SHAFT - INSTALLATION.........19-31
WORM SHAFT - REMOVAL.............19-30
WORN THREADS - STANDARD
PROCEDURE, REPAIR
DAMAGED OR...............9-11,9-122,9-66
BR/BEINDEX 35
Description Group-Page Description Group-Page Description Group-Page