Radio removal DODGE RAM 2003 Service Owner's Manual

(11) Install the right a-pillar trim panel. (Refer to
23 - BODY/INTERIOR/A-PILLAR TRIM - INSTAL-
LATION)
(12) Position the right end cap and seat the
attachment clips fully.
(13) Install the one HVAC mounting screw.
(14) Connect the radio antenna.
(15) Connect the two electrical connectors at the
right cowl panel.
(16) Install the right cowl trim cover. (Refer to 23 -
BODY/INTERIOR/COWL TRIM - INSTALLATION)
(17) Connect the air bag control module electrical
connector.
(18) Install the center bracket bolts and tighten to
12 N´m (9 ft. lbs.).
(19) Install the floor console, if equipped. (Refer to
23 - BODY/INTERIOR/FLOOR CONSOLE - INSTAL-
LATION)
(20) Install the air bag control module cover, if
equipped.
(21) Connect the park brake release handle actua-
tor rod.
(22) Install the hood release handle and tighten
the screws.
(23) Install the two bolts at the column support
bracket and tighten to 14 N´m (10 ft. lbs.).
(24) Install the steering column. (Refer to 19 -
STEERING/COLUMN - INSTALLATION)
(25) Connect the wire harness electrical connectors
above the brake pedal.
(26) Install the two top instrument panel bolts and
tighten to 12 N´m (9 ft. lbs.).
(27) Install the four top instrument panel screws.
(28) Install the instrument panel top cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL TOP COVER - INSTALLATION)
INSTRUMENT PANEL
HEADLAMP SWITCH BEZEL
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULDRESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Using a trim stick C-4755 or equivalent,
release the top clips on the steering column opening
cover and the lower drivers side bezel.
(2) Using a trim stick C-4755 or equivalent,
release the switch bezel. (Fig. 17)
(3) Disconnect the electrical connector and remove
the bezel.
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Connect the electrical connector.
(2) Position the switch bezel and seat the attach-
ment clips fully.
(3) Seat the clips on the steering column opening
cover and the lower drivers side bezel fully.
Fig. 17 HEADLIGHT SWITCH BEZEL
1 - SWITCH BEZEL
2 - INSTRUMENT PANEL
3 - ELECTRICAL CONNECTOR
4 - HEADLIGHT SWITCH
DRINSTRUMENT PANEL 23 - 57
INSTRUMENT PANEL ASSEMBLY (Continued)

DISTRIBUTION
TABLE OF CONTENTS
page page
AIR OUTLETS
REMOVAL - PANEL OUTLETS.............24
INSTALLATION - PANEL OUTLETS..........24
BLEND DOOR
REMOVAL.............................24
INSTALLATION.........................25
BLOWER MOTOR
DESCRIPTION.........................25
OPERATION...........................25
DIAGNOSIS AND TESTING - BLOWER
MOTOR .............................26
REMOVAL.............................26
INSTALLATION.........................26
DEFROST DOOR
REMOVAL - DEFROST DOOR.............27
INSTALLATION - DEFROST DOOR..........27
FLOOR DISTRIBUTION DUCTS
REMOVAL.............................27INSTALLATION.........................27
HVAC HOUSING
REMOVAL.............................27
DISASSEMBLY.........................28
ASSEMBLY............................28
INSTALLATION.........................29
INSTRUMENT PANEL DUCTS
REMOVAL.............................29
INSTALLATION.........................29
MODE DOOR
REMOVAL - FLOOR - DEFROST DOOR......30
INSTALLATION - FLOOR - DEFROST DOOR . . 30
RECIRC DOOR
REMOVAL.............................30
INSTALLATION.........................30
AIR OUTLETS
REMOVAL - PANEL OUTLETS
(1) Use a trim stick or another suitable wide flat-
bladed tool to gently pry the panel outlet grill out of
the panel outlet housing (Fig. 1). The panel outlet
grill is retained by a light snap fit.
INSTALLATION - PANEL OUTLETS
To install, position the grill housing in the panel
outlet housing and press firmly until it snaps into
place.
BLEND DOOR
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
Fig. 1 Dash Panel
1 - Headlight Switch
2 - Air Outlets
3 - Instrument Cluster
4 - Climate Control
5 - Radio
6 - Airbag
7 - Glove Box
8 - Heated Seat Switch (if equipped)
9 - Transfer Case Control Switch (if equipped)
10 - Cigar Lighter
11 - Cup Holders
12 - Ash Tray (if equipped)
13 - Power Outlet
24 - 24 DISTRIBUTIONDR

GOVERNOR - REMOVAL, ELECTRONIC . . 21-198,
21-378
GRAB HANDLE - INSTALLATION,
B-PILLAR...........................23-69
GRAB HANDLE - REMOVAL, B-PILLAR....23-69
GRILLE - INSTALLATION...............23-40
GRILLE - INSTALLATION, COWL.........23-38
GRILLE - REMOVAL..................23-39
GRILLE - REMOVAL, COWL............23-38
GRILLE FRAME - INSTALLATION.........23-40
GRILLE FRAME - REMOVAL............23-40
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO.............................8W-01-10
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-10
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION..................8A-9
GROUNDS - DESCRIPTION, POWER......8E-10
GUIDE SEALS - DESCRIPTION, VALVE . 9-31,9-36
GUIDES - DESCRIPTION, VALVE....9-106,9-197
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES............9-246,9-305
HALF SHAFT - CAUTION................3-11
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-11
HALF SHAFT - INSTALLATION............3-12
HALF SHAFT - REMOVAL...............3-11
HALF SHAFT - SPECIAL TOOLS..........3-12
HALF SHAFT - SPECIFICATIONS..........3-12
HANDLE - INSTALLATION, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - INSTALLATION, B-PILLAR
GRAB..............................23-69
HANDLE - INSTALLATION, EXTERIOR....23-20,
23-30
HANDLE - INSTALLATION, RELEASE.......5-38
HANDLE - REMOVAL, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - REMOVAL, B-PILLAR GRAB....23-69
HANDLE - REMOVAL, EXTERIOR . . . 23-20,23-30
HANDLE - REMOVAL, RELEASE..........5-38
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-22,23-32
HANDLE ACTUATOR - REMOVAL, INSIDE . 23-22,
23-31
HANDLE/LATCH REMOTE -
INSTALLATION, RELEASE..............23-17
HANDLE/LATCH REMOTE - REMOVAL,
RELEASE...........................23-17
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-33
HAT BRAKE - INSPECTION, REAR DRUM
IN .................................5-33
HAZARD SWITCH - DESCRIPTION.......8L-13
HAZARD SWITCH - OPERATION.........8L-13
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-44
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION..........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-44
HD - INSTALLATION, 4X4..............19-15
HD - INSTALLATION, ALL LD & HD
EXCEPT 4X4........................19-15
HD - REMOVAL, 4X4
..................19-14
HD - REMOVAL, ALL LD & HD EXCEPT
4X4
...............................19-14
HD EXCEPT 4X4 HD - INSTALLATION,
ALL LD
............................19-15
HD EXCEPT 4X4 HD - REMOVAL, ALL LD
. 19-14
HEAD - CLEANING, CYLINDER
.....9-195,9-300,
9-372HEAD - DESCRIPTION, CYLINDER . . 9-106,9-243,
9-298,9-370
HEAD - INSPECTION, CYLINDER . . . 9-195,9-301,
9-372
HEAD - INSTALLATION, CYLINDER . . 9-195,9-372
HEAD - INSTALLATION, LEFT CYLINDER . . 9-110
HEAD - INSTALLATION, RIGHT
CYLINDER..........................9-111
HEAD - LEFT - INSTALLATION,
CYLINDER...........................9-23
HEAD - LEFT - REMOVAL, CYLINDER......9-21
HEAD - OPERATION, CYLINDER....9-194,9-243
HEAD - REMOVAL, CYLINDER.....9-195,9-298,
9-371
HEAD - REMOVAL, LEFT CYLINDER......9-106
HEAD - REMOVAL, RIGHT CYLINDER.....9-108
HEAD - RIGHT - INSTALLATION,
CYLINDER...........................9-32
HEAD - RIGHT - REMOVAL, CYLINDER....9-32
HEAD COVER - INSTALLATION,
CYLINDER..........................9-304
HEAD COVER - REMOVAL, CYLINDER....9-304
HEAD COVER GASKET - DESCRIPTION,
CYLINDER..........................9-243
HEAD COVER GASKET - OPERATION,
CYLINDER..........................9-243
HEAD COVER(S) - CLEANING, CYLINDER . 9-245,
9-374
HEAD COVER(S) - DESCRIPTION,
CYLINDER.................9-121,9-26,9-373
HEAD COVER(S) - INSPECTION,
CYLINDER.....................9-245,9-374
HEAD COVER(S) - INSTALLATION,
CYLINDER........9-196,9-245,9-27,9-36,9-374
HEAD COVER(S) - REMOVAL, CYLINDER . 9-196,
9-245,9-26,9-35,9-373
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-20
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER....9-194,9-243,9-370
HEAD GASKET SELECTION - STANDARD
PROCEDURE........................9-330
HEADLAMP - INSTALLATION............8L-13
HEADLAMP - REMOVAL...............8L-13
HEADLAMP ALIGNMENT - SPECIAL
TOOLS..............................8L-7
HEADLAMP SWITCH - DESCRIPTION.....8L-14
HEADLAMP SWITCH - INSTALLATION....8L-14
HEADLAMP SWITCH - OPERATION.......8L-14
HEADLAMP SWITCH - REMOVAL........8L-14
HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT PANEL.....23-57
HEADLAMP SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-57
HEADLAMP UNIT - ADJUSTMENTS......8L-15
HEADLAMP UNIT - INSTALLATION.......8L-15
HEADLAMP UNIT - REMOVAL...........8L-15
HEADLINER - INSTALLATION...........23-69
HEADLINER - REMOVAL...............23-69
HEADREST - INSTALLATION............23-82
HEADREST - REMOVAL................23-82
HEADREST SLEEVE - INSTALLATION.....23-82
HEADREST SLEEVE - REMOVAL.........23-82
HEAT SHIELDS - DESCRIPTION..........11-7
HEAT SHIELDS - INSTALLATION..........11-8
HEAT SHIELDS - REMOVAL.............11-7
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-5
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-6
HEATED SEAT ELEMENT - INSTALLATION . . 8G-6
HEATED SEAT ELEMENT - OPERATION.....8G-6
HEATED SEAT ELEMENT - REMOVAL......8G-6
HEATED SEAT MODULE - DESCRIPTION....8E-6
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING........................8E-7
HEATED SEAT MODULE - INSTALLATION
. . . 8E-7
HEATED SEAT MODULE - OPERATION
.....8E-6
HEATED SEAT MODULE - REMOVAL
.......8E-7
HEATED SEAT SENSOR - DESCRIPTION
....8G-7
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING
........................8G-7HEATED SEAT SENSOR - OPERATION.....8G-7
HEATED SEAT SENSOR - REMOVAL.......8G-7
HEATED SEAT SWITCH - DESCRIPTION....8G-7
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SWITCH - INSTALLATION . . . 8G-9
HEATED SEAT SWITCH - OPERATION......8G-8
HEATED SEAT SWITCH - REMOVAL.......8G-9
HEATED SEAT SYSTEM - DESCRIPTION....8G-3
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SYSTEM - OPERATION.....8G-4
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-44
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-43
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-42
HEATER - DESCRIPTION, FUEL..........14-63
HEATER - DESCRIPTION, INTAKE AIR.....14-91
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-42
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-63
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-43
HEATER - INSTALLATION, INTAKE AIR......14-91
HEATER - OPERATION, ENGINE BLOCK....7-42
HEATER - OPERATION, FUEL............14-63
HEATER - OPERATION, INTAKE AIR......14-91
HEATER - REMOVAL, ENGINE BLOCK......7-43
HEATER - REMOVAL, INTAKE AIR........14-91
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-14
HEATER CORE - DESCRIPTION..........24-50
HEATER CORE - INSTALLATION.........24-50
HEATER CORE - OPERATION............24-50
HEATER CORE - REMOVAL.............24-50
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-5
HEATER RELAY - DESCRIPTION, FUEL....14-64
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-92
HEATER RELAY - INSTALLATION, FUEL . . . 14-64
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-93
HEATER RELAY - OPERATION, FUEL......14-64
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-92
HEATER RELAY - REMOVAL, FUEL.......14-64
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-93
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-27
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-10
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER
...................8L-10
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-35
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-36
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE
..........................22-6
HIGH/LOW RELAY - DESCRIPTION,
WIPER
.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER
.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER
.............................8R-21
HIGH/LOW RELAY - OPERATION, WIPER
. . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER
. . . 8R-21
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

MOLDING - INSTALLATION, REAR DOOR
INNER BELT.........................23-94
MOLDING - INSTALLATION, REAR DOOR
OUTER BELT........................23-94
MOLDING - REMOVAL, FRONT DOOR
INNER BELT.........................23-93
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT........................23-93
MOLDING - REMOVAL, REAR DOOR
INNER BELT.........................23-94
MOLDING - REMOVAL, REAR DOOR
OUTER BELT........................23-94
MOLDINGS - INSTALLATION, BODY SIDE . . 23-36
MOLDINGS - REMOVAL, BODY SIDE.....23-36
MONITORED SYSTEMS - DESCRIPTION....25-1
MONITORS - DESCRIPTION,
COMPONENT.........................25-4
MOTOR - DESCRIPTION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - DESCRIPTION, BLOWER.......24-25
MOTOR - DESCRIPTION, DOOR LOCK.....8N-5
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-33
MOTOR - DESCRIPTION, LUMBAR.......8N-19
MOTOR - DESCRIPTION, SHIFT . . 21-686,21-720
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-26
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-5
MOTOR - DIAGNOSIS AND TESTING,
LUMBAR...........................8N-20
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-34
MOTOR - INSTALLATION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - INSTALLATION, BLOWER......24-26
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-35
MOTOR - INSTALLATION, SHIFT . . 21-686,21-720
MOTOR - INSTALLATION, STARTER......8F-37
MOTOR - OPERATION, BLOWER.........24-25
MOTOR - OPERATION, DOOR LOCK.......8N-5
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-33
MOTOR - OPERATION, LUMBAR........8N-20
MOTOR - OPERATION, SHIFT....21-686,21-720
MOTOR - REMOVAL, ADJUSTABLE
PEDAL..............................5-24
MOTOR - REMOVAL, BLOWER..........24-26
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-34
MOTOR - REMOVAL, SHIFT.....21-686,21-720
MOTOR - REMOVAL, STARTER..........8F-34
MOTOR - REMOVAL, WINDOW..........8N-22
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-38
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-39
MOTOR RELAY - OPERATION, STARTER . . . 8F-38
MOTOR RELAY - REMOVAL, STARTER....8F-39
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER...................24-18
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-17
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER
..............24-18
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER
...........................24-17
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER
...........................24-18
MOTOR SWITCH - DESCRIPTION,
BLOWER
...........................24-18
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER
...................24-18
MOTOR SWITCH - INSTALLATION,
BLOWER
...........................24-19
MOTOR SWITCH - OPERATION, BLOWER
. . 24-18
MOTOR SWITCH - REMOVAL, BLOWER
. . . 24-19
MOUNT - INSTALLATION, DISC BRAKE
CALIPER ADAPTER
....................5-17
MOUNT - INSTALLATION, FRONT
. . . 9-144,9-211,
9-265,9-335,9-392,9-58
MOUNT - INSTALLATION, REAR
....9-147,9-213,
9-267,9-337,9-393,9-60
MOUNT - REMOVAL, FRONT
. 9-144,9-211,9-264,
9-335,9-392,9-57
MOUNT - REMOVAL, REAR
. . 9-147,9-213,9-266,
9-337,9-393,9-60MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-10
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-10
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-3
MUFFLER - 5.9L DIESEL - INSTALLATION . . 11-9
MUFFLER - 5.9L DIESEL - REMOVAL......11-9
MUFFLER - INSTALLATION..............11-8
MUFFLER - REMOVAL..................11-8
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-19
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-38
NAME PLATES - REMOVAL, EXTERIOR....23-38
NATURAL VAC LEAK DETECTION ASSY -
DESCRIPTION.......................25-23
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-24
NATURAL VAC LEAK DETECTION ASSY -
OPERATION.........................25-23
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-24
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER...............7-61
NEW MODULE / SWITCH OPERATING
MODES, STANDARD PROCEDURE -
CONFIGURING A......................8Q-3
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-12
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY.....................8N-13
NOISE - DIAGNOSIS AND TESTING, A/C
COMPRESSOR.......................24-36
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-7
NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-8
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-10
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO...................8A-8
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO.....................8A-9
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
OPERATION..........................25-8
NOZZLE - DESCRIPTION, WASHER......8R-12
NOZZLE - INSTALLATION, WASHER......8R-12
NOZZLE - OPERATION, WASHER........8R-12
NOZZLE - REMOVAL, WASHER..........8R-12
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-2
NV241 GENII - ASSEMBLY, TRANSFER
CASE.............................21-604
NV241 GENII - CLEANING, TRANSFER
CASE.............................21-602
NV241 GENII - DESCRIPTION, TRANSFER
CASE................................0-4
NV241 GENII - DESCRIPTION, TRANSFER
CASE.............................21-591
NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER CASE............21-592
NV241 GENII - DISASSEMBLY,
TRANSFER CASE
....................21-593
NV241 GENII - INSPECTION, TRANSFER
CASE
.............................21-602
NV241 GENII - INSTALLATION,
TRANSFER CASE
....................21-614
NV241 GENII - OPERATION, TRANSFER
CASE
.............................21-591
NV241 GENII - REMOVAL, TRANSFER
CASE
.............................21-593NV241 GENII - TRANSFER CASE........21-614
NV241/NV243 - TRANSFER CASE . 21-615,21-680
NV243 - ASSEMBLY, TRANSFER CASE . . . 21-670
NV243 - CLEANING, TRANSFER CASE . . . 21-668
NV243 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV243 - DESCRIPTION, TRANSFER CASE . 21-658
NV243 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-659
NV243 - DISASSEMBLY, TRANSFER
CASE.............................21-660
NV243 - INSPECTION, TRANSFER CASE . . 21-668
NV243 - INSTALLATION, TRANSFER
CASE.............................21-679
NV243 - OPERATION, TRANSFER CASE . . 21-659
NV243 - REMOVAL, TRANSFER CASE....21-660
NV243 - TRANSFER CASE.............21-680
NV271 - ASSEMBLY, TRANSFER CASE . . . 21-637
NV271 - CLEANING, TRANSFER CASE . . . 21-635
NV271 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV271 - DESCRIPTION, TRANSFER CASE . 21-623
NV271 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-624
NV271 - DISASSEMBLY, TRANSFER
CASE.............................21-625
NV271 - INSPECTION, TRANSFER CASE . . 21-635
NV271 - INSTALLATION, TRANSFER
CASE.............................21-649
NV271 - OPERATION, TRANSFER CASE . . 21-623
NV271 - REMOVAL, TRANSFER CASE....21-625
NV271 - TRANSFER CASE.............21-649
NV271/NV273, SPECIAL TOOLS -
TRANSFER CASE..............21-650,21-714
NV273 - ASSEMBLY, TRANSFER CASE . . . 21-701
NV273 - CLEANING, TRANSFER CASE . . . 21-698
NV273 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV273 - DESCRIPTION, TRANSFER CASE . 21-687
NV273 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-688
NV273 - DISASSEMBLY, TRANSFER
CASE.............................21-689
NV273 - INSPECTION, TRANSFER CASE . . 21-699
NV273 - INSTALLATION, TRANSFER
CASE.............................21-713
NV273 - OPERATION, TRANSFER CASE . . 21-688
NV273 - REMOVAL, TRANSFER CASE....21-689
NV273 - TRANSFER CASE.............21-713
NV3500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-17
NV3500 - CLEANING, MANUAL
TRANSMISSION......................21-15
NV3500 - DESCRIPTION, MANUAL
TRANSMISSION.......................21-1
NV3500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION...............21-3
NV3500 - DISASSEMBLY, MANUAL
TRANSMISSION.......................21-4
NV3500 - INSPECTION, MANUAL
TRANSMISSION......................21-15
NV3500 - INSTALLATION, MANUAL
TRANSMISSION......................21-38
NV3500 - OPERATION, MANUAL
TRANSMISSION.......................21-1
NV3500 - REMOVAL, MANUAL
TRANSMISSION.......................21-3
NV3500 - SPECIAL TOOLS, MANUAL
TRANSMISSION......................21-40
NV3500 - SPECIFICATIONS, MANUAL
TRANSMISSION......................21-39
NV4500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-61
NV4500 - CLEANING, MANUAL
TRANSMISSION......................21-60
NV4500 - DESCRIPTION, MANUAL
TRANSMISSION......................21-42
NV4500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION..............21-43
NV4500 - DISASSEMBLY, MANUAL
TRANSMISSION......................21-44
NV4500 - INSPECTION, MANUAL
TRANSMISSION
......................21-60
NV4500 - INSTALLATION, MANUAL
TRANSMISSION
......................21-77
NV4500 - OPERATION, MANUAL
TRANSMISSION
......................21-42
NV4500 - REMOVAL, MANUAL
TRANSMISSION
......................21-43
NV4500 - SPECIAL TOOLS, MANUAL
TRANSMISSION
......................21-79
22 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-560
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-559
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-559
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-343
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-35
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-343
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-343
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-36
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-343
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-72
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-72
PRESSURE SENSOR - OPERATION, FUEL . . 14-72
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-72
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-66
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL...............9-343,9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-66
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL..................9-343,9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-45
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-45
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC....21-140,21-321,21-493
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-15
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C................................24-15
PRESSURE TRANSDUCER - REMOVAL,
A/C................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION...........................22-6
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM.......................14-59
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER.......8N-10
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-8
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER....8Q-4
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - INSTALLATION,
FRONT...............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, FRONT....3-6
PROPELLER SHAFT - REMOVAL, REAR.....3-7
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-43
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-43
PULLEY - INSTALLATION..............19-46
PULLEY - REMOVAL
..................19-45
PUMP - 5.7L - INSTALLATION, WATER
.....7-71
PUMP - 5.7L - REMOVAL, WATER
........7-70
PUMP - 5.9L - CLEANING, WATER
........7-64
PUMP - 5.9L - DESCRIPTION, WATER
.....7-62PUMP - 5.9L - INSPECTION, WATER......7-64
PUMP - 5.9L - INSTALLATION, WATER.....7-64
PUMP - 5.9L - OPERATION, WATER.......7-62
PUMP - 5.9L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-67
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER .............................7-67
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-68
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-68
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-67
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-67
PUMP - ASSEMBLY, OIL......9-156,9-274,9-68
PUMP - ASSEMBLY, OIL . . 21-215,21-393,21-566
PUMP - CLEANING, OIL.....9-155,9-218,9-344,
9-398
PUMP - CLEANING, OIL . . 21-214,21-393,21-566
PUMP - DESCRIPTION................19-38
PUMP - DESCRIPTION, FUEL...........14-12
PUMP - DESCRIPTION, FUEL INJECTION . . 14-64
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-75
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL.....21-212,21-392,
21-562
PUMP - DESCRIPTION, WATER..........7-64
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-67
PUMP - DISASSEMBLY, OIL . . . 9-155,9-272,9-67
PUMP - DISASSEMBLY, OIL.....21-212,21-393,
21-564
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-39
PUMP - INSPECTION, OIL . . . 9-155,9-218,9-272,
9-344,9-399,9-67
PUMP - INSPECTION, OIL . 21-214,21-393,21-566
PUMP - INSTALLATION, FUEL INJECTION . 14-67
PUMP - INSTALLATION, FUEL TRANSFER . 14-76
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-157,9-219,9-274,
9-344,9-400,9-68
PUMP - OPERATION..................19-38
PUMP - OPERATION, FUEL.............14-12
PUMP - OPERATION, FUEL INJECTION....14-64
PUMP - OPERATION, FUEL TRANSFER....14-76
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL . 21-212,21-392,21-562
PUMP - OPERATION, WATER............7-64
PUMP - REMOVAL, FUEL INJECTION.....14-65
PUMP - REMOVAL, FUEL TRANSFER.....14-76
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL.....9-154,9-218,9-272,
9-343,9-398,9-67
PUMP BYPASS - DESCRIPTION, WATER . . . 7-64
PUMP BYPASS - OPERATION, WATER.....7-65
PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL, WATER......7-68
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER......7-69
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-567
PUMP FRONT SEAL - REMOVAL, OIL
....21-567
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-39
PUMP MODULE - DESCRIPTION, FUEL
....14-12
PUMP MODULE - INSTALLATION, FUEL
. . . 14-13
PUMP MODULE - OPERATION, FUEL
.....14-12
PUMP MODULE - REMOVAL, FUEL
.......14-12
PUMP RELAY - DESCRIPTION, FUEL
.....14-33
PUMP RELAY - INSTALLATION, FUEL
.....14-33
PUMP RELAY - OPERATION, FUEL
.......14-33
PUMP RELAY - REMOVAL, FUEL
........14-33
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL
...............8I-7
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION
.............14-65PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-563
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-301
PUSHRODS - INSPECTION.............9-302
QUAD CAB - INSTALLATION............8O-32
QUAD CAB - REMOVAL................8O-29
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE.........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-60
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-59
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-60
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-60
RADIATOR - 5.9L DIESEL - OPERATION....7-59
RADIATOR - 5.9L DIESEL - REMOVAL.....7-59
RADIATOR - CLEANING.................7-58
RADIATOR - DESCRIPTION..............7-56
RADIATOR - INSPECTION.................7-58
RADIATOR - INSTALLATION.............7-58
RADIATOR - OPERATION................7-56
RADIATOR - REMOVAL.................7-57
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-61
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-61
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-57,7-59
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-41
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-41
RADIATOR FAN - CLEANING.............7-40
RADIATOR FAN - INSPECTION...........7-40
RADIATOR FAN - INSTALLATION..........7-40
RADIATOR FAN - REMOVAL.............7-39
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-60
RADIATOR PRESSURE CAP - OPERATION . . 7-61
RADIO - DESCRIPTION.................8A-7
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-7
RADIO - REMOVAL....................8A-7
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION..................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL....................8A-9
RAIL - DESCRIPTION, FUEL
............14-13
RAIL - DESCRIPTION, FUEL INJECTOR
....14-89
RAIL - INSTALLATION, FUEL
............14-18
RAIL - INSTALLATION, FUEL INJECTOR
. . . 14-90
RAIL - OPERATION, FUEL
..............14-13
RAIL - OPERATION, FUEL INJECTOR
.....14-89
RAIL - REMOVAL, FUEL
...............14-13
RAIL - REMOVAL, FUEL INJECTOR
.......14-89
RAIL REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER
.................13-12
RAIL TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME
..............................13-4
RAIL WEATHERSTRIP - INSTALLATION,
DRIP
..............................23-91
RAIL WEATHERSTRIP - REMOVAL, DRIP
. . 23-91
RAIL WEATHERSTRIP RETAINER -
INSTALLATION, DRIP
.................23-92
26 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

STEM SEALS - REMOVAL, VALVE........9-377
STOP LAMP - INSTALLATION, CENTER
HIGH MOUNTED.....................8L-10
STOP LAMP - REMOVAL, CENTER HIGH
MOUNTED..........................8L-10
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-10
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-10
STORAGE BIN - INSTALLATION..........23-62
STORAGE BIN - INSTALLATION, UNDER
SEAT ..............................23-81
STORAGE BIN - REMOVAL.............23-62
STORAGE BIN - REMOVAL, UNDER SEAT . . 23-81
STORAGE BIN COVERING -
INSTALLATION, UNDER SEAT...........23-81
STORAGE BIN COVERING - REMOVAL,
UNDER SEAT........................23-81
STORAGE BIN LATCH - INSTALLATION,
UNDER SEAT........................23-81
STORAGE BIN LATCH - REMOVAL,
UNDER SEAT........................23-81
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-8
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND...............8A-10
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND................8A-8
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRETCH - INSPECTION, MEASURING
TIMING CHAIN.................9-279,9-405
STRIKER - INSTALLATION, LATCH . . 23-17,23-24,
23-33
STRIKER - REMOVAL, LATCH . 23-17,23-24,23-33
STRIKER / SECONDARY CATCH -
INSTALLATION, LATCH................23-48
STRIKER / SECONDARY CATCH -
REMOVAL, LATCH....................23-48
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-113
STRUCTURAL COVER - DESCRIPTION....9-143,
9-210,9-56
STRUCTURAL COVER - INSTALLATION . . . 9-143,
9-210,9-56
STRUCTURAL COVER - OPERATION.....9-143,
9-210,9-56
STRUCTURAL COVER - REMOVAL . . 9-143,9-210,
9-56
STUDS - INSTALLATION...............22-14
STUDS - REMOVAL...................22-14
SUN VISOR - INSTALLATION...........23-71
SUN VISOR - REMOVAL...............23-71
SUN VISOR SUPPORT - INSTALLATION . . . 23-72
SUN VISOR SUPPORT - REMOVAL.......23-72
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-7
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-10
SUPPLIES - OPERATION, 5 VOLT........8E-11
SUPPLY TEST - DIAGNOSIS AND
TESTING, VACUUM....................8P-2
SUPPORT - INSTALLATION, SUN VISOR
. . . 23-72
SUPPORT - REMOVAL, SUN VISOR
......23-72
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR
..................23-71
SUPPORT BRACKET - INSTALLATION,
STEERING COLUMN OPENING
..........23-62
SUPPORT BRACKET - REMOVAL,
STEERING COLUMN OPENING
..........23-61
SUPPORT CYLINDER - INSTALLATION
....23-49
SUPPORT CYLINDER - INSTALLATION,
LOAD FLOOR
........................23-73
SUPPORT CYLINDER - REMOVAL
........23-48
SUPPORT CYLINDER - REMOVAL, LOAD
FLOOR
.............................23-73
SUPPORT PLATE - INSTALLATION
........5-29
SUPPORT PLATE - REMOVAL
............5-29
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE
............8A-8
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE
...........8A-10SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE..............8A-8
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE...............8A-9
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET...........9-10
SURROUND - INSTALLATION,
INSTRUMENT PANEL LOWER...........23-60
SURROUND - REMOVAL, INSTRUMENT
PANEL LOWER......................23-60
SUSPENSION - DESCRIPTION, GEAR -
INDEPENDENT FRONT.................19-16
SUSPENSION - INSTALLATION, GEAR -
INDEPENDENT FRONT.................19-17
SUSPENSION - REMOVAL, GEAR -
INDEPENDENT FRONT.................19-16
SUSPENSION - STANDARD PROCEDURE,
ALIGNMENT LINK/COIL..................2-5
SUSPENSION ARM - INSTALLATION,
LOWER.............................2-35
SUSPENSION ARM - REMOVAL, LOWER . . . 2-35
SUSPENSION, SPECIAL TOOLS - FRONT . . . 2-11
SWITCH - DESCRIPTION................8P-8
SWITCH - DESCRIPTION, BACKUP LAMP . . . 8L-7
SWITCH - DESCRIPTION, BLOWER
MOTOR............................24-18
SWITCH - DESCRIPTION, BRAKE LAMP....8L-8
SWITCH - DESCRIPTION, CLUTCH
PEDAL POSITION.....................6-14
SWITCH - DESCRIPTION, DOOR AJAR....8L-25
SWITCH - DESCRIPTION, DRIVER SEAT . . . 8N-15
SWITCH - DESCRIPTION, HAZARD.......8L-13
SWITCH - DESCRIPTION, HEADLAMP....8L-14
SWITCH - DESCRIPTION, HEATED SEAT . . . 8G-7
SWITCH - DESCRIPTION, HORN..........8H-2
SWITCH - DESCRIPTION, IGNITION.......19-9
SWITCH - DESCRIPTION, KEY-IN
IGNITION...........................19-11
SWITCH - DESCRIPTION, LUMBAR
CONTROL..........................8N-19
SWITCH - DESCRIPTION, OVERDRIVE . . . 21-218,
21-397,21-568
SWITCH - DESCRIPTION, PASSENGER
AIRBAG ON/OFF.....................8O-38
SWITCH - DESCRIPTION, PASSENGER
SEAT ..............................8N-16
SWITCH - DESCRIPTION, POWER
STEERING PRESSURE.................19-45
SWITCH - DESCRIPTION, SEAT BELT.....8O-46
SWITCH - DESCRIPTION, SELECTOR....21-685,
21-719
SWITCH - DESCRIPTION, WASHER
FLUID LEVEL.........................8R-9
SWITCH - DIAGNOSIS AND TESTING,
BACKUP LAMP.......................8L-8
SWITCH - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-18
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-9
SWITCH - DIAGNOSIS AND TESTING,
CLUTCH PEDAL POSITION..............6-14
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT.......................8N-15
SWITCH - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-8
SWITCH - DIAGNOSIS AND TESTING,
HORN..............................8H-2
SWITCH - DIAGNOSIS AND TESTING,
IGNITION............................19-9
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT....................8N-17
SWITCH - DIAGNOSIS AND TESTING,
POWER LOCK........................8N-4
SWITCH - DIAGNOSIS AND TESTING,
POWER MIRROR....................8N-13
SWITCH - DIAGNOSIS AND TESTING,
SEAT BELT .........................8O-47
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-22
SWITCH - INSTALLATION
...............8P-9
SWITCH - INSTALLATION, ADJUSTABLE
PEDAL
...............................5-6
SWITCH - INSTALLATION, BLOWER
MOTOR
............................24-19
SWITCH - INSTALLATION, BRAKE LAMP
. . 8L-10
SWITCH - INSTALLATION, DRIVER SEAT
. . 8N-16SWITCH - INSTALLATION, HEADLAMP....8L-14
SWITCH - INSTALLATION, HEATED SEAT . . . 8G-9
SWITCH - INSTALLATION, IGNITION......19-11
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-19
SWITCH - INSTALLATION, OVERDRIVE . . 21-219,
21-397,21-569
SWITCH - INSTALLATION, PASSENGER
AIRBAG ON/OFF.....................8O-39
SWITCH - INSTALLATION, PASSENGER
SEAT ..............................8N-18
SWITCH - INSTALLATION, POWER LOCK . . . 8N-4
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-11
SWITCH - INSTALLATION, WINDOW.....8N-23
SWITCH - OPERATION.................8P-8
SWITCH - OPERATION, BACKUP LAMP....8L-8
SWITCH - OPERATION, BLOWER MOTOR . . 24-18
SWITCH - OPERATION, BRAKE LAMP......8L-8
SWITCH - OPERATION, CLUTCH PEDAL
POSITION...........................6-14
SWITCH - OPERATION, DOOR AJAR......8L-25
SWITCH - OPERATION, DRIVER SEAT....8N-15
SWITCH - OPERATION, HAZARD.........8L-13
SWITCH - OPERATION, HEADLAMP......8L-14
SWITCH - OPERATION, HEATED SEAT.....8G-8
SWITCH - OPERATION, IGNITION.........19-9
SWITCH - OPERATION, LUMBAR
CONTROL............................8N-19
SWITCH - OPERATION, OVERDRIVE....21-218,
21-397,21-568
SWITCH - OPERATION, PASSENGER
AIRBAG ON/OFF.....................8O-38
SWITCH - OPERATION, PASSENGER
SEAT ..............................8N-17
SWITCH - OPERATION, POWER
STEERING PRESSURE.................19-45
SWITCH - OPERATION, SEAT BELT.......8O-46
SWITCH - OPERATION, SELECTOR.....21-685,
21-719
SWITCH - OPERATION, WASHER FLUID
LEVEL..............................8R-9
SWITCH - REMOVAL...................8P-9
SWITCH - REMOVAL, ADJUSTABLE
PEDAL...............................5-6
SWITCH - REMOVAL, BLOWER MOTOR . . . 24-19
SWITCH - REMOVAL, BRAKE LAMP.......8L-9
SWITCH - REMOVAL, DRIVER SEAT......8N-16
SWITCH - REMOVAL, HEADLAMP........8L-14
SWITCH - REMOVAL, HEATED SEAT.......8G-9
SWITCH - REMOVAL, IGNITION.........19-10
SWITCH - REMOVAL, LUMBAR
CONTROL..........................8N-19
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OVERDRIVE......21-219,
21-397,21-568
SWITCH - REMOVAL, PASSENGER
AIRBAG ON/OFF.....................8O-39
SWITCH - REMOVAL, PASSENGER SEAT . . 8N-17
SWITCH - REMOVAL, POWER LOCK......8N-4
SWITCH - REMOVAL, POWER MIRROR . . . 8N-13
SWITCH - REMOVAL, WASHER FLUID
LEVEL.............................8R-10
SWITCH - REMOVAL, WINDOW.........8N-23
SWITCH AND KEY LOCK CYLINDER -
DIAGNOSIS AND TESTING, IGNITION.....19-11
SWITCH BEZEL - INSTALLATION,
INSTRUMENT PANEL HEADLAMP........23-57
SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL HEADLAMP........23-57
SWITCH OPERATING MODES,
STANDARD PROCEDURE -
CONFIGURING A NEW MODULE..........8Q-3
SWITCH VALVE - DESCRIPTION,
SOLENOID.........................21-574
SWITCH VALVE - OPERATION, SOLENOID . 21-574
SWITCHES - DESCRIPTION, REMOTE.....8A-10
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-11
SWITCHES - INSTALLATION, REMOTE....8A-12
SWITCHES - OPERATION, REMOTE
......8A-10
SWITCHES - REMOVAL, REMOTE
........8A-12
SYMBOLS - DESCRIPTION,
INTERNATIONAL
....................Intro.-6
SYMBOLS - DESCRIPTION,
INTERNATIONAL
.......................0-1
TABLE, SPECIFICATIONS - A/C
APPLICATION
........................24-7
DRINDEX 33
Description Group-Page Description Group-Page Description Group-Page