diagram DODGE RAM SRT-10 2006 Service Repair Manual

P0108-INLET AIR PRESSURE SENSOR VOLTAGE TOO HIGH
For a complete wiring diagramRefer to Section 8W.

P0111-INTAKE AIR TEMPERATURE (IAT) SENSOR RATIONALITY
For a complete wiring diagramRefer to Section 8W.

P0112-INTAKE AIR TEMPERATURE (IAT) SENSOR VOLTAGE TOO LOW
For a complete wiring diagramRefer to Section 8W.

P0113-INTAKE AIR TEMPERATURE (IAT) SENSOR VOLTAGE TOO HIGH
For a complete wiring diagramRefer to Section 8W.

P0116-ENGINE COOLANT TEMPERATURE (ECT) SENSOR RATIONALITY
For a complete wiring diagramRefer to Section 8W.

P0117-ENGINE COOLANT TEMPERATURE (ECT) SENSOR VOLTAGE TOO LOW
For a complete wiring diagramRefer to Section 8W.

P0118-ENGINE COOLANT TEMPERATURE (ECT) SENSOR VOLTAGE TOO HIGH
For a complete wiring diagramRefer to Section 8W.

P0128-THERMOSTAT RATIONALITY
For a complete wiring diagramRefer to Section 8W.
When Monitored:
While the engine is running.
Set Condition:
The coolant temperature does not rise by a calibrated amount over a calibratedamountoftime.
Possible Causes
COOLING FAN
COOLANT TEMPERATURE SENSOR
THERMOSTAT
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.COOLING FAN
NOTE: refer to the no trouble code test*Fan Operation Testto ensure the fan is operating properly.
Is the cooling fan operating properly?
Ye s>>
Go To 2
No>>
Repair the cooling fan.
Perform POWERTRAIN VERIFICATION TEST VER - 2 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
2.COOLANT TEMPERATURE SENSOR
Operate the engine for 10 minutes while monitoring the coolant temperaturewiththescantool.
Did the coolant temperature change over time while the engine was running?
Ye s>>
Go To 3
No>>
Replace the coolant temperature sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 2 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
3.THERMOSTAT
NOTE: refer to the no trouble code test*Thermostat Testto ensure the thermostat is operating properly.
is the thermostat operating properly?
Ye s>>
Te s t C o m p l e t e .
No>>
Replace the thermostat.
Perform POWERTRAIN VERIFICATION TEST VER - 2 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0148-HIGH PRESSURE COMMON RAIL (HPCR) CHECKSUM
For a complete wiring diagramRefer to Section 8W.
When Monitored:
While the engine is running.
Set Condition:
A deviation between the fuel pressure set point and the actual fuel pressure.
Possible Causes
OTHERS DTC’S PRESENT
FUEL LEAKS
FUEL CONTROL ACTUATOR
FUEL PRESSURE SENSOR
CASCADE OVERFLOW VALVE
CHECK VALVE DAMAGED OR BLOCKED
FUEL RETURN LINES OBSTRUCTION, DAMAGE, OR DEBRIS
LIFT PUMP FLOW
AIRINFUELSYSTEM
LEAKING FUEL INJECTORS OR HIGH PRESSURE CONNECTORS
PRESSURE LIMITING VALVE
HIGH PRESSURE FUEL PUMP
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.OTHERS DTC’S PRESENT
With the scan tool, read DTCs.
Are any other DTC’s present?
Ye s>>
Repair other DTC’s first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
No>>
Go To 2
2.FUEL LEAKS
Ensure that the fuel level is above 15% using the scan tool.
Visually inspect the low and high pressure side of the fuel system for fuel leaks or damaged components.
Do you have any fuel leaks or damaged components?
Ye s>>
Repair the fuel leak.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 3

P0169-WATER IN FUEL (WIF) LIGHT ON TOO LONG
For a complete wiring diagramRefer to Section 8W.