oil change DODGE SPRINTER 2005 1.G Owners Manual

STARTING AND OPERATING 179
5
SNOW CHAINSInstall snow chains on rear wheels only. Install snow
chains on exterior wheel in vehicles with double tires.
Comply with the manufacturer’s installation
instructions.
NOTE: Vehicles with snow chains installed are only to
be driven on a snow-covered surface. The snow chains
must be removed on road surfaces free of snow.FUEL REQUIREMENTSUse only commercially available vehicular diesel fuels
No. 2 or No. 1 (ASTM D 975 No. 2-D or No. 1-D).
NOTE: Because of its better quality the manufacturer
recommends the use of commercially available
vehicular diesel fuel No. 2.
For information on cold weather operation, contact
your authorized Sprinter Dealer. If diesel fuels are used with a sulphur content
exceeding 0.5 % by weight, engine oil change intervals
must be shortened. Please contact your Sprinter Dealer
to obtain the necessary information.
Refueling from drums or canisters may lead to the fuel
becoming contaminated. This in turn can cause faults
in the fuel system. Always f
ilter the fuel before adding
it to the vehicle’s tank.
WARNING!
Marine diesel fuel, Bio diesel fuel, heating oil or
the like must not be used.
Do not blend diesel fuel with marine diesel fuel,
Bio diesel fuel or heating oil.
The use of such non-approved fuels or blending
diesel fuel may result in malfunction or cause
engine damage. Damage or malfunctions
resulting from poor fuel quality or from blending
specific fuel additives are not covered by the
Sprinter Warranty.

WHAT TO DO IN EMERGENCIES 199
6
Procedure:
1. Park the vehicle on a firm, level, non-slippery surface.
2. Switch on the hazard warning flasher switch, apply the parking brake, and place the transmission
selector in "P".
3. Everyone must leave the vehicle before you jack it up.
4. Everyone must leave the danger zone, before jacking the vehicle. 5. The vehicle must be safeguarded in accordance
with legal regulations (such as using a warning
triangle).
6. Prevent vehicle from rolling away by blocking wheels with wheel chocks (not supplied with
vehicle) or sizable wood block or stone.
On a level road, place one chock in front of and one
behind the wheel that is diagonally opposite to the
wheel being changed.
When changing a wheel on mild uphill or downhill
grades, place chocks on the downhill side blocking
both wheels of the other axle.
Do not jack the vehicle up more than 1.2 in (30
mm) between the tire and the surface. Otherwise,
the vehicle may tip over and may cause serious
injury or death to you or others.
Precautions when changing a wheel:
For the torque, refer to
"Installing a wheel ";
Do not damage, grease or oil wheel bolts or their
threads.
WARNING!
Do not change wheels on either steep uphill or
downhill grades. The vehicle may begin to move
and fall from the jack which could cause personal
injury and property damage.

WHAT TO DO IN EMERGENCIES 207
6
NOTE: The optional light alloy wheels are supplied
with 5 short wheel lug bolts enclosed for the steel spare
wheel in the vehicle tool kit.
 Before fitting the spare wheel, clean rust and dirt off the contact surfaces of the wheel and the wheel hub,
and from the wheel bolts.
 Note the specified wheel and tire size, tire load capacity and speed code.
 Do not change the tire’s direction of rotation.
 Do not damage, grease or oil wheel bolts or their threads.
WARNING!
Different wheel bolts are required for pressed
steel and light-alloy wheels.
Incorrect wheel lug bolts for the wheels could
work loose, thereby causing you to lose control of
the vehicle. This could cause an accident resulting
in severe personal injuries and and property
damage.
WARNING!
Incorrect mounting bolts or improperly tightened
mounting bolts can cause the wheel to come off.
To avoid the risk of serious or fatal injuries or ve-
hicle damage, please bear the following points in
mind:• Always replace wheel bolts that are damaged or
rusted.• Never apply oil or grease to wheel bolts• If a wheel hub thread is damaged, you must not
drive the vehicle. Consult a qualified specialist
workshop.

220 MAINTAINING YOUR VEHICLEApproved Engine OilsNOTE: Use only engine oils that are labeled on the
container as meeting the specifications of API (American
Petroleum Institute) and/or DaimlerChrysler specification
sheets MB 228.3, 228.5, 229.3 and 229.5, such as MOPAR®
SAE 15W-40 HD Diesel Engine Oil (e.g. MOPAR® Part
No. 04798231AD), or equivalent.Always refer to the following viscosity chart for the
proper viscosity grade based on ambient temperature.
Select oil viscosity according to the lowest air
temperature expected before the next oil change.
For further information, contact your authorized
Sprinter Dealer. NOTE: This chart supercedes ALL previously
published viscosity charts.

226 MAINTAINING YOUR VEHICLE
If the engine is already at its regular operating
temperature:
Add coolant until the coolant level is about 0.6 inch
(1.5 cm) above the base area which is visible
through the filler opening.
 Replace and tighten the radiator cap.
If a large quantity of coolant has been lost, or if smaller
amounts are lost at regular intervals, have the engine
cooling system examined by an authorized Sprinter
Dealer.
For coolant composition and water quality, contact
your Sprinter Dealer.
WINTER OPERATIONHave your vehicle winterized by an authorized
Sprinter Dealer before the onset of winter.
 Have the engine oil changed, if the engine oil filled is not approved for winter use.
 Coolant: antifreeze/anti-corrosion concentration in the coolant checked.
 Windshield washer system: add winter concentrate to the washer fluid.
 Battery: the battery will lose capacity as temperatures drop. Only a well-charged battery will
ensure reliable engine starting even at low outside
temperatures.
 Tires: fit M+S radial tires, taking note of the maximum permissible speed of the tires fitted.

MAINTENANCE SCHEDULES
CONTENTS
8M A
I
N T
E
N A
N CE
S
C
H E
D
U L
E
S


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264


Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264


Maintenance - Without ASSYST Maintenance
Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Maintenance Intervals . . . . . . . . . . . . . . . . . . . . 265


Maintenance - With ASSYST Maintenance
Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266


Regular Check-Ups. . . . . . . . . . . . . . . . . . . . . . . . . 266


Special Maintenance Requirements . . . . . . . . . . . 267
Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Dust Filter for Heating/Ventilation
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267


Engine Oil Change and Filter Replacement . . . . 267
Once a Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267


Scope of Work for Maintenance service . . . . . . . 268
Oil Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Additional Maintenance Work . . . . . . . . . . . . . 270
Additional Maintenance Work After ... Years . . . 270

MAINTENANCE SCHEDULES 267
8M A
I
N T
E
N A
N CE
S
C
H E
D
U L
E
S
SPECIAL MAINTENANCE REQUIREMENTSIf bodies built by manufacturers other than
DaimlerChrysler Corporation are fitted to the vehicle, the
maintenance requirements and lubrication intervals
specified by the body manufacturer must be adhered to,
in addition to all standard maintenance requirements.Brake FluidOnly use brake fluids approved by the manufacturer
(DOT 4 plus). Information about brake fluids is
available from your Sprinter Dealer.CoolantHave the corrosion inhibitor/antifreeze concentration
in the coolant checked before the onset of winter (once
a year in countries with h igh prevailing temperatures).
Have the coolant renewed every five years or 100,000
miles.Dust Filter for Heating/Ventilation ReplacementThe dust filter and the tailgate interior filter are
renewed during routine maintenance service.
However, if operating conditions are dusty, these
filters should be renewed more frequently.
ENGINE OIL CHANGE AND FILTER
REPLACEMENTIn a minimum, change the engine oil and oil filter once
a year - even if the vehicle mileage per year is extremly
low. For standard oil service schedules, please see the
chapter oil service and maintenance service.Once a YearSelect the viscosity of the engine oil (SAE classes)
according to the outside air temperature.
Only use engine oil approved by DaimlerChrysler
Corporation if following the ASSYST system
guidelines.
Information is available from your Sprinter Dealer.
If the fuel used has a sulphur content exceeding 0.05 %
by weight, the service interval s should be split in half.
If the sulphur content of the fuel used is between 0.3%
and 0.8% by weight, the service intervals should be
split in half (i.e. every 5,000 miles instead of every
10,000 miles).

268 MAINTENANCE SCHEDULES
M A I
N T
E
N A
N
C E
S
C
H
E
D
U L
E
S8
SCOPE OF WORK FOR MAINTENANCE SERVICE
Oil ServiceOil change
Engine:
Oil change and filter replacement
Check fluid levels of the following system, refill as
necessary.
If fluid is lost, trace and eliminate cause – as a separate
order.
Power-assisted steering
Lubrication work:
Trailer tow hitch (original equipment)
Maintenance
ASSYST maintenance computer reset Function check
Signalling system,
warning and indicator lamps
Headlamps, exterior lighting
Windscreen wipers,
windscreen washer system
Check for leaks and damage.
Check for abrasion points and ensure that
lines are correctly routed!
All assemblies:
Engine, transmission, transfer case, front axle, rear
axle, steering, power steering pump
All lines and hoses, sensor cables
Rubber boots on front axle drive shafts,
rubber boots on front axle suspension ball joints, shock
absorbers

270 MAINTENANCE SCHEDULES
M A I
N T
E
N A
N
C E
S
C
H
E
D
U L
E
S8
Additional Maintenance WorkAutomatic transmission once only at 80,000 miles/
128000km
Oil and filter change
During every second maintenance service
Air cleaner without maintenance indicator:
Air cleaner filter element renewal
Check poly-V-belt for wear and signs of damage
During every sixth maintenance service
Rear axle
Additional Maintenance Work After ... YearsEvery 2 years
Change brake fluid
Every 3 years
Air cleaner filter element renewal
(note installation date
)
Every 15 years or 100,000 miles
Coolant renewal
Note coolant composition

INDEX 283
10
Acceleration Skid Control Warning Lamp . 143, 166
Additional Brake Lamp . . . . . . . . . . . . . . . . . . . . . 252
Anti-Lock Brake System (ABS) Indicator Lamp. 161
Battery Charge Indicator Lamp . . . . . . . . . . . . . . 104
Brake Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Coolant Level Indicator Lamp . . . . . . . . . . . . . . . 106
Electronic Brake Force Distribution . . . . . . . . . . . 157
Engine Control Unit Indicator Lamp . . . . . . . . . . 107
Engine Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Engine Oil Level Indicator Lamp . . . . . . . . . . . . . 105
Exit Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Indicator Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
License Plate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 252
Reading Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
Reserve Fuel Indicator Lamp . . . . . . . . . . . . . . . . 103
Seat Belt Warning Lamp . . . . . . . . . . . . . . . . . . . . . 44
Side-Marker Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 253
SRS Malfunction Indicator Lamp . . . . . . . . . . . . . . 49
Taillamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Water in Fuel Indicator Lamp . . . . . . . . . . . . . . . . 104 Lifting Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Lighter, Cigar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Lighting, Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Lock, Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Locking, Central . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
MMaintenance Computer . . . . . . . . . . . . . . . . . . . . . . . 110
Maintenance Intervals . . . . . . . . . . . . . . . . . . . . . . . . . 265
Maintenance Schedules
Additional Maintenance Work After ... Years . . 270
Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Dust Filter for Heating/Ventilation Replacement . .
267
Engine Oil Change and Filter Replacement . . . . 267
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Oil Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Once a Year . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Regular Check-Ups . . . . . . . . . . . . . . . . . . . . . . . . . 266
Scope of Work for Maintenance service . . . . . . . 268