clock DODGE SPRINTER 2006 1.G User Guide

STARTING AND OPERATING 215
5
NOTE: Prior to opening water drain screw (3), place a
suitable receptacle underneath the drain hose (2). Turn
water drain screw (3) on and off only by hand.
Diesel fuels and diesel fuel mixtures must be disposed
of properly; we recommend water be drained from fuel
filters by an authorized Sprinter Dealer.
Draining Fuel Filter
 Stop the engine.
 Shift gear selector lever to ‘‘P’’ position.
 Open the hood.
 Place a suitable receptacle underneath the drain
hose (2).
 Turn the key in the ignition lock to position 2. Open immediately the water drain screw (3) about 1
turn (counterclockwise) until fluid emerges. Ensure
that the fluid is collected in the receptacle.
 Close the water drain screw (3) as soon as about 0.25
US qt (0.2 liters) are emerged.
 After draining, return the key in the ignition lock to
position 0.
 Dispose of the collected fluid in an environmentally
responsible manner.
 If the filter is still saturated, drain the filter once
more.
After draining, the engine may run briefly but stall for
lack of fuel. If this occurs, bleed the system.
NOTE: Should the water in the fuel indicator lamp
still not go out after the fuel filter has been drained
twice, the cause should be examined by an authorized
Sprinter Dealer.
CAUTION!
Delaying draining of the fuel filter for a
considerable time after the indicator lamp lights
up may lead to engine damage.

WHAT TO DO IN EMERGENCIES 239
6
JACK Using the Jack
The jack is located together with the vehicle tool kit
under the hatch in the front passenger footwell, refer to
"Vehicle Tool Kit".
1. Loosen the wheel bolts before raising the vehicle.
2. Close the release valve on the jack.
3. Assemble the pump lever provided and insert it
into the socket on the jack.
4. Secure the lever by turning it clockwise in the
socket.
Position the jack under the appropriate jack point and
raise the vehicle by pumping the lever.
WARNING!
To avoid the risk of serious or fatal injuries or vehicle
damage, please bear the following points in mind:
 The jack is intended only for raising the vehicle
briefly, for instance, when changing a wheel. If it is
not designed to enable work to be carried out
underneath the vehicle.
Do not crawl under the jacked-up vehicle. For work
under the vehicle, stands must be used.
 The jack must be placed on a firm, flat surface only.
 Do not change wheels on uphill or downhill
gradients under any circumstances.
 Make sure that no persons are present in the vehicle
when jacking up the vehicle.
 Do not start the engine while the vehicle is raised.
 Make sure that the distance between the underside
of the tires and the ground does not exceed 1.2 in (30
mm). Otherwise the vehicle may tip over.

280 MAINTAINING YOUR VEHICLE
No. Rated Circuit
1. 10A Parking lamp right, taillamp right
2. 10A High beam head lamp,right
3. 10A High beam head lamp, left,
high beam indicator lamp
4. 10A Backup lamp
5. 10A Brake lamp
6. 20A Windshield wiper motor
7. 15A Horn, heated rear window,
air recirculation switch,
optional equipment relay (terminal 15)
8. 20A Interior lighting, cigarette lighter,
radio (terminal 30)
9. 15A Clock, hazard warning lamps,
parking lamps10. 10A Instrument lighting, license plate lamp
daytime driving lamps
11. 10A Side lamp, left; taillamp, left
12. 10A Low beam headlamp, right
13. 10A Low beam headlamp, left
14. 15A Fog lamp
15. 10A Radio (terminal 15)
16. 25A Engine control unit
17. 15A Engine control unit
18. 15A Ignition (terminal 15)
19. 15A Not in use
20. 15A Heater controls (terminal 30)
21. 30A Heater blower (terminal 30)

MAINTAINING YOUR VEHICLE 285
7Turn signal lamp and sidemarker lamp,
3457 NA – 12V 28 / 7.5W, yellow glass (1)
Low beam headlamp, H7 – 12V 55W (2)
Fog lamp, H1 – 12V 55W (3)
Side and parking lamps, W5W – 12V 5W (4)
High beam headlamps, H1 – 12V 55 (5)Turn Signal Lamps and Side-Marker Lamps
1. Turn bulb holder, together with bulb,
counterclockwise and remove.
2. Remove the bulb from the bulb holder.
3. Insert a new bulb in the bulb holder.
4. Insert the bulb holder together with the bulb and
turn clockwise to the stop.

MAINTAINING YOUR VEHICLE 289
7
Taillamps
Cargo/Passenger Van
Locked (1)
Unlocked (2)
Bulbs are changed from inside the cargo area.
The rear lamp cluster bulb holder is located behind the
interior paneling. Remove the paneling.Brake lamp, taillamp, standing lamp,
P21/5W – 12V 21/5W (1)
Backup lamp, P21W – 12V 21W (2)
Turn signal lamp, P21W – 12V 21W (3)
Side-marker lamp, R5W – 12V 5W (4)
1. Unclip and remove the bulb socket.
2. To change a bulb, press the bulb into the bulb
socket, turn it counterclockwise and remove.
3. Insert the new bulb.
4. Clip the bulb socket into place.

290 MAINTAINING YOUR VEHICLE
Chassis
(1) Retaining screws
(2) Clearance lamp, R5W - 12V 5W
(3) Turn signal lamp, P21W - 12V 21W
(4) Stop lamp, P21W - 12V 21W
(5) Taillamp, R5W - 12V 5W
(6) Backup lamp, P21W - 12V 21W
(7) License plate lamp (driver‘s side only),
R5W - 12V 5W1. Loosen retaining screw a and remove lamp
housing.
2. To change a bulb, press the bulb into the bulb
socket, turn it counterclockwise and remove.
3. Insert the new bulb.
4. Install lamp housing.

MAINTAINING YOUR VEHICLE 291
7
License Plate Lamps
(Cargo/Passenger Vans Only)
1. Press the bulb socket to the left, against the force of
the spring, and remove.
2. Replace the bulb, C5W – 12V 5W.
3. Install the cover.
4. Re-install the bulb socket.Additional Brake Lamp
(Cargo/Passenger Vans Only)
(1) Retaining screws
1. Take out the retaining screws (1) and remove the
lamp housing.
2. To change a bulb, P21W – 12V 21W
Press the bulb into the bulb socket, turn it
counterclockwise and remove.
3. Insert the new bulb.
4. Install the lamp housing.

292 MAINTAINING YOUR VEHICLE
Side-Mounted Turn Signals
1. Press the lamp housing to the front, against the
force of the spring, and remove.
2. Replace the bulb, W5W - 12V 5W
3. Install the bulb socket.Side-Marker Lamps,
Standing Lamps (Optional)
Retaining screws (1) Bulb socket (2)
1. Take out the retaining screws (1) and remove the
lamp housing.
2. Turn the bulb socket (2) counterclockwise and
remove.
3. Replace the bulb, W3W – 12V 3W.
4. Install the bulb socket (2).

MAINTAINING YOUR VEHICLE 293
7
Identification Lamps (Cargo/passenger vans only)
(1) Retaining screw
1. Take out the retaining screw (1) and remove the
lamp housing.
2. To change a bulb, 12V 4CP
Press the bulb into the bulb socket, turn it
counterclockwise and remove.
3. Insert the new bulb.
4. Install the lamp housing.Interior Lighting in Passenger Compartment and
Load Compartment
1. Align a screwdriver on the retaining spring, press it
in and pry the lamp housing out.
2. Replace the bulb, K – 12V 18W
3. Install the lamp housing.

320 INDEX
Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Comfortseat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Comfortseat (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . 61
Compartments in Front Doors. . . . . . . . . . . . . . . . . . . 87
Constant RPMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Consumer Assistance
Be Reasonable with Request . . . . . . . . . . . . . . . . . 312
If You Need Assistance . . . . . . . . . . . . . . . . . . . . . 312
Prepare a List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Prepare for the Appointment . . . . . . . . . . . . . . . . 312
Coolant Level Indicator Lamp . . . . . . . . . . . . . . . . . . 108
Coolant Temperature Gauge . . . . . . . . . . . . . . . . . . . 103
Coolant, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Cooling System, Engine . . . . . . . . . . . . . . . . . . . . . . . 261
Corrosion Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 269
Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
DDe-Fogging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Dehumidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
De-Icing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Diesel Fuels for Use at Very Low Temperatures . . 211Direction of Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Displaying Engine Oil Level . . . . . . . . . . . . . . . . . . . 115
Doors
Front Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Rear Cargo Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Sliding Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Draining Fuel Filter with Water Separator . . . . . . . 214
Driver’s Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Driving Safety Systems . . . . . . . . . . . . . . . . . . . . . . . . 163
EElectric Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Electrical Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Fuse and Relay Optional Equipment . . . . . . . . . . 281
Fuse, Relay, and Diode Assignments - Optional
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Relay Assignment, Standard Equipment . . . . . . 281
Standard Fuse and Relay Equipment. . . . . . . . . . 277
Electrical Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Electronic Brake Force Distribution . . . . . . . . . . . . . 167
Electronic Brake Force Distribution Lamp . . . . . . . . 160
Electronic Stability Program . . . . . . . . . . . . . . . . . . . 169
Emission Label, Vehicle/Engine . . . . . . . . . . . . . . . . . . 8