tire type DODGE SPRINTER 2006 1.G User Guide

STARTING AND OPERATING 179
5
Radial-Ply Tires
Cuts and punctures in radial tires are repairable only in
the tread area because of sidewall flexing. Consult an
authorized tire dealer for radial tire repairs.
Important Guidelines
Only use sets of tires and rims of the same type and
make.
 Tires must be of the correct size for the rim.
 Break in new tires for approximately 65 miles (100
km) at moderate speeds.
WARNING!
Fitting other wheel sizes to the vehicle will change
the vehicle’s handling characteristics andmay lead
to an accident resulting in death, severe personal
injuries and property damage.
Only certain tires meeting the tire size/load/speed
rating specifications are certified to conform to
FMVSS 110 for the Sprinter vehicle at this time.
Please check your side walls of your originally
equipped tires for specific makes/sizes, and speed
load ratings when you need to replace your tires.
To prevent accidents resulting in possible death,
severe injury or property damage, use only the tire
andwheel sizeswith load ratings approved for
your Sprinter vehicle for your tire replacement.
Refer to "Tire and Loading Information"WARNING!
Combining radial ply tires with other types of
tires on your Sprinter vehicle will cause your ve-
hicle to handle poorly. The instability could cause
an accident.
Always use radial ply tires in sets of 4 (or 6, in case
of vehicles with dual rear wheels).
Never combine them with other types of tires.

STARTING AND OPERATING 185
5
Vehicles type 2500 C/HC/SHC
The vehicles are factory equipped with "L" or "N"-rated
tires, which have a speed rating of 74 mph (120 km/h)
or 87 mph (140 km/h) respectively.
Vehicles type 3500 C/HC/SHC
The vehicles are factory equipped with "L", "N" or "R"-
rated tires, which have a speed rating of 74 mph (120
km/h), 87 mph (140 km/h) or 106 mph (170 km/h)
respectively.
Tire Grip
Tire grip is greatly reduced on a wet, snow covered or
icy road. Speed and driving style must therefore be
adapted to suit road conditions. The safe speed on a
wet, snow covered or icy road is always lower than on
a dry road.
Below a tread depth of 1/8 in (3 mm), tire grip begins
to decrease rapidly on wet roads.
Pay particular attention to the condition of the road
whenever the outside temperatures are close to the
freezing point.Hydroplaning
Depending on the depth of the water layer on the road,
hydroplaning may occur, even at low speeds and with
new tires. Reduce vehicle speed, avoid track grooves in
the road, and apply brakes cautiously in the rain.
In winter, install M+S radial tires with a minimum
tread depth of approximately 1/6 in (4 mm) on all
wheels to ensure normal balanced handling
characteristics. On packed snow, they can reduce your
stopping distance compared to summer tires.
Stopping distance, however, is still considerably
greater than when the road is not covered with snow or
ice. Exercise appropriate caution.
For information on winter tires, refer to "Winter
Operation".
WARNING!
If ice has formed on the road, tire traction will be
substantially reduced. Under such weather condi-
tions, drive, steer and brake with extreme caution.

186 STARTING AND OPERATING
Recommended Tire Inflation Pressure
The tire inflation pressure (including the spare wheel)
should be checked regularly and adjusted as well asinspecting for signs of tire wear or visible damage. Use
a good quality pocket-type gauge to check tire inflation
pressure.
Do not make a visual judgement when determining
proper inflation. Radial tires may look properly
inflated even when they are underinflated.
The tire inflation pressure should be checked
regularly, i.e. at least each time you refuel the vehicle,
and should only be adjusted on cold tires. The
preferred interval for checking the tire inflation
pressure, however, is before each trip.
The tires can be considered cold if the vehicle has been
parked for at least 3 hours or driven less than 1 mile
(1.6 km) at an ambient temperature of approximately
68 °F (20 °C).
Follow recommended cold tire inflation pressures
listed on Tire and Loading Information placard on the
driver’s door B-pillar.
Keeping the tires properly inflated provides the best
handling, tread life and riding comfort.
The pressure difference between the tires on a single
axle should not exceed 1.5 psi (10 kPa).
WARNING!
Avoid spinning of one drive wheel. This may
cause serious damage to the drivetrain which is
not covered by the Warranty.
WARNING!
Follow recommended tire inflation pressures.
Do not underinflate tires. Underinflated tires
wear excessively and/or unevenly, adversely
affect handling and fuel economy, and are more
likely to fail from being overheated.
Do not overinflate tires. Overinflated tires can
adversely affect handling and ride comfort, wear
unevenly, increase stopping distance, and result
in sudden deflation (blowout) because they are
more likely to become punctured or damaged by
road debris, potholes etc.

STARTING AND OPERATING 193
5
Tire Sizes for Sprinter Vehicles
1. Vehicles with programmed top speed limit of 68
mph (109 km/h) only.
Design Standard
Depending on the design standards used, the tire size
molded into the sidewall may have no letter or a letter
(1) preceding the tire width or the tire load rating
designation.
Letter "LT" preceding the tire width designation:
Light Truck tire based on U.S. design standards.
Letter "C" preceding the tire load rating designation:
Commercial vehicle tire based on European design
standards.Tire Width
The tire width (2) indicates the nominal tire width in
mm.
Aspect Ratio
The aspect ratio (3) is the dimensional relationship
between tire section height and section width and is
expressed in percentage. The aspect ratio is arrived at
by dividing section height by section width.
Tire Code
The tire code (4) indicates the tire construction type.
The “R” stands for radial tire type. Letter “D” means
diagonal or bias ply construction; letter “B” means
belted-bias ply construction.
Rim Diameter
The rim diameter (5) is the diameter of the bead seat,
not the diameter of the rim edge. Rim diameter is
indicated in inches (in).
Tire Load Rating
The tire load rating (6) is a numerical code associated
with the maximum load a tire can support. Sprinter type
2500 C/HC/SHC 3500 C/HC/SHC
225/70 R 15 C 112/110 R
(115 N)195/70 R 15 C 104/102 R
LT 225/75 R 16 115/112 N LT 225/75 R 16 115/112 N
LT 225/75 R 16 115/112 L
1LT 225/75 R 16 115/112 L1

194 STARTING AND OPERATING
For example, a load rating of 115 corresponds to a
maximum load of 2680 lbs (1215 kg) the tire is designed
to support.
If two values are given (as illustrated), the first value,
preceding the slash "/", applies to single tires (rear
axle).
The second value, succeeding the slash "/", applies to
twin tires (dual wheel rear axle).
The commercial vehicle tires based on European
standards may have an additional value in the
parentheses (as illustrated). In such case, the value
preceding the parentheses is valid for European
countries and the parenthesized for the USA and
Canada.
Refer also to "Maximum Tire Load" where the
maximum load associated with the load index is
indicated in kilograms and lbs.
NOTE: Tire load rating (6) and tire speed rating (7) are
also referred to as "service description".
WARNING!
The tire load rating must always be at least half of
the GAWR of your vehicle. Otherwise, tire failure
may be the result which may cause an accident
and/or serious personal injury to you or others.
For information on GAWR, refer to "Tire and
Loading Terminology".
Always replace rims and tires with the same
designation, manufacturer and type as shown on
the original part.
WARNING!
Do not overload the tires by exceeding the specified
load limit as indicated on the Tire and Loading Infor-
mation placard on the driver’s door B-pillar.
Overloading the tires can overheat them, possibly
causing a blowout.
Overloading the tires can also result in handling
or steering problems, or brake failure.

196 STARTING AND OPERATING
DOT, Tire Identification Number (TIN)
(1) DOT
(2) Manufacturer’s identification mark
(3) Tiresize
(4) Tire type code (at the option of the tire
manufacturer)
(5) Date of manufacture NOTE: Data shown on tire are for illustration purposes
only. Actual data on tires are specific to each vehicle
and may vary from data shown in the illustration.
U.S. tire regulations require each new
tiremanufacturer or tire retreader to mold a TIN into or
onto a sidewall of each tire produced.
The TIN is a unique identifier which facilitates efforts by
tire manufactures to notify purchasers in recall situations
or other safety matters concerning tires and gives
purchasers the means to easily identify such tires.
The TIN is comprised of "Manufacturer’s identification
mark", "Tire size", "Tire type code" and "Date of
manufacture".
The TIN may be found on one or both sides of the tire
however the date code may only be on one side. Tires
with white sidewalls will have the full TIN including
date code located on the white sidewall side of the tire.
Look for the TIN on the outboard side of black sidewall
tires as mounted on the vehicle.
If the TIN is not found on the outboard side then you
will find it on the inboard side of the tire. In this case,
the tire must be remounted. Make sure the TIN is

STARTING AND OPERATING 197
5
visible on the outboard side of the tire and if applicable
that the direction of rotation is correct when
remounting the tire.
Rotation (spinning) direction, refer to "Direction of
Rotation".
DOT (Department Of Transportation)
A tire branding symbol (1) which denotes the tire
meets requirements of the U.S. Department of
Transportation.
Manufacturer’s Identification Mark
Themanufacturer’s identificationmark (2) denotes the
tire manufacturer.
New tires have a mark with two symbols.
Retreaded tires have a mark with four symbols. For
more information on retreaded tires, refer to "Tires and
Wheels".
Tire Size
The code (3) indicates the tire size.Tire Type Code
The code (4) may, at the option of the manufacturer, be
used as a descriptive code for identifying significant
characteristics of the tire.
Date of Manufacture
The date of manufacture (5) identifies the week and
year of manufacture.
The first two figures identify the week, starting with
“01” to represent the first full week of the calendar
year. The second two figures represent the year.
For example, "0301" represents the 3rd week of 2001.
NOTE: Prior to July 2000, tire manufacturers were only
required to have 1 number to represent the year in
which the tire was manufactured.
For example, "031" could represent the 3rd week of
1981 or 1991.
NOTE: If the date of manufacture code indicated on the
tire is less than 4 figures, do not use it.

200 STARTING AND OPERATING
Tire Ply Material
(1) Plies in sidewall
(2) Plies under tread
NOTE: Data shown on tire are for illustration purposes
only. Actual data on tires are specific to each vehicle
and may vary from data shown in the illustration.
This marking tells you about the type of cord and
number of plies in the sidewall and under the tread.Tire and Loading Terminology
Accessory Weight
The combined weight (in excess of those standard
items which may be replaced) of automatic
transmission, power steering, power brakes, power
windows, radio, and heater, to the extent that these
items are available as factory-installed equipment
(whether installed or not).
Air Pressure
The amount of air inside the tire pressing outward on
each square inch of the tire. Air pressure is expressed
in pounds per square inch (psi), or kilopascal (kPa) or
bars.
Aspect Ratio
Dimensional relationship between tire section height
and section width expressed in percentage.
Bar
Another metric unit for air pressure. There are 14.5038
pounds per square inch (psi) to 1 bar; there are 100
kilopascals (kPa) to 1 bar.

STARTING AND OPERATING 203
5
TIN (Tire Identification Number)
Unique identifier which facilitates efforts by tire
manufacturers to notify purchasers in recall situations
or other safety matters concerning tires and gives
purchases the means to easily identify such tires. The
TIN is comprised of "Manufacturer’s identification
mark", "Tire size", "Tire type code" and "Date of
manufacture".
Tire Load Rating
Numerical code associated with the maximum load a
tire can support.
Tire Ply Composition and Material used
This indicates the number of plies or the number of
layers of rubber-coated fabric in the tire tread and
sidewall. Tire manufacturers also must indicate the ply
materials in the tire and sidewall, which include steel,
nylon, polyester, and others.
Tire Speed Rating
Part of tire designation; indicates the speed range for
which a tire is approved.Traction
Force exerted by the vehicle on the road via the tires.
The amount of grip provided.
Tread
The portion of a tire that comes into contact with the
road.
Treadwear Indicators
Narrow bands, sometimes called "wear bars" that
show across the tread of a tire when only 1/16 in (1.6
mm) of tread remains.
TWR (Tongue Weight Rating)
Maximum permissible weight on trailer tongue.
Uniform Tire Quality Grading Standards
A tire information system that provides consumers
with ratings for a tire’s traction, temperature and
treadwear.
Ratings are determined by tire manufacturers using
government testing procedures. The ratings are
molded into the sidewall of the tire.

204 STARTING AND OPERATING
Vehicle Capacity Weight
Rated cargo and luggage load plus 68 kilograms (150
lbs) times the vehicle’s designated seating capacity.
Vehicle Maximum Load on the Tire
Load on an individual tire that is determined by
distributing to each axle its share of the maximum
loaded vehicle weight and dividing it by two.
Rotating Tires
Tires on the front and rear axles of vehicles operate at
different loads and perform different steering, driving
and braking functions. For these reasons, they wear at
unequal rates, and develop irregular wear patterns.
These effects can be reduced by timely rotation of tires.
The benefits of rotation are especially worthwhile with
aggressive tread designs such as those on On/Off
Road type tires. Rotation will increase tread life, help tomaintain mud, snow, and wet traction levels, and
contribute to a smooth, quiet ride.
If applicable to your vehicle's tire configuration, tires
can be rotated according to the tire manufacturer’s
recommended intervals in the tire manufacturer’s
warranty pamphlet located in your vehicle literature
portfolio. If none is available, tires should be rotated
every 10000 miles (16000 km), or sooner if necessary,
according to the degree of tire wear.
The same rotation (spinning) direction must be
maintained when fitted, see "Direction of Rotation".
Rotate tires before the characteristic tire wear pattern
becomes visible (shoulder wear on front tires and
treadcenter wear on rear tires).
The reasons for any rapid or unusual wear should be
corrected prior to rotation being performed.
Thoroughly clean the mounting face of wheels and
brake disks, i.e. the inner side of the wheels/tires,
during each rotation. Check for and ensure proper tire
inflation pressure, refer to "Recommended Tire
Inflation Pressure".
WARNING!
Rotate front and rear wheels only if the tires are of
the same dimension.