jump cable DODGE SPRINTER 2008 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2008, Model line: SPRINTER, Model: DODGE SPRINTER 2008 2.GPages: 666, PDF Size: 14.11 MB
Page 583 of 666
581 Practical hints
Jump-starting
5
\3 Jump-startingIf the starter battery in the battery re-
cess in the driver’s footwell is dis-
charged, the engine can be jump-started
from another vehicle using jump leads.
For this purpose, the vehicle is equipped
with a jump-starting connection point.
Please note:
\4
Jump-starting must only be per-
formed when the engine and catalyt-
ic converter are cold.
\4
Do not start the engine if the battery
has frozen. Let the battery thaw out
first.
\4
Only use a battery of the same rated
voltage and of approximately the
same capacity for jump-starting.
\4
Only use jumper cables of adequate
cross-section with insulated battery
terminal clamps.
iThe auxiliary battery* in the engine
compartment is not suitable for
jump-starting operations. Only use
the jump-starting connection in the
engine compartment if you require
jump-starting assistance or wish to
provide jump-starting assistance.
!
CAUTION
Avoid repeated and lengthy starting
attempts.
Never start the vehicle using a rapid
battery charger.
Warning
G
Avoid creating sparks. Keep naked flames
away from the battery, and do not smoke.
Comply with safety precautions and spe-
cial protective measures when handling
batteries (\2page 335).
nf_BA.book Page 581 Friday, January 25, 2008 3:53 PM
Page 584 of 666
582 Practical hintsJump-starting
5
\1
Make sure that the two vehicles do
not touch.
\1
Apply the handbrake or move the se-
lector lever to position
P.
\1
Switch off all electrical consumers.
\1
Switch on the battery isolating
switch* if necessary (
\2
page 338).
\1
Remove the key from the ignition
lock.
\1
Open the hood (
\2
page 318).
The jump-starting connection point is on
the left-hand side of the air cleaner in
the engine compartment when looking
in the direction of travel.
Jump-starting connection point
1Positive terminal clamp of jumper cable\1
Remove the positive terminal cover
from the donor battery.
\1
Connect positive terminal of donor
battery
2
to jump-starting connec-
tion point 1
with the jumper cable.
Start with the donor battery.
\1
Using red positive terminal clamp
1
of the jumper cable, slide the red
protective cap of the jump-starting
connection point back with a clock-
wise turn and connect the positive
terminal clamp of the jumper cable
to the positive terminal of the jump-
starting connection point.
nf_BA.book Page 582 Friday, January 25, 2008 3:53 PM
Page 585 of 666
583 Practical hints
Jump-starting
5
1Positive terminal of jump-starting con-
nection point (under cover)
2Positive terminal of donor battery
3Negative terminal of donor battery
4Ground contact of own vehicle
(negative terminal of your own battery)
\1
Run the other vehicle’s engine at
idling speed.
\1
Connect negative terminal
3
of the
donor battery to ground contact
4
of your own vehicle.
Start with the donor battery.
\1
Start the engine.
\1
Disconnect the jumper cable from
negative terminal
3
of the battery
and ground contact 4
first, then
from positive terminal 2
of the bat-
tery and jump-starting connection
point
1
.
The red protective cap springs back
to its initial position when the termi-
nal clamp is removed from the jump-
starting connection point.
\1
Have the battery checked at an
authorized Sprinter Dealer.
iDo not connect the jumper cable to
the auxiliary battery* in the engine
compartment. This is not suitable for
jump-starting operations.
nf_BA.book Page 583 Friday, January 25, 2008 3:53 PM