key battery DODGE VIPER 2006 ZB / 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2006, Model line: VIPER, Model: DODGE VIPER 2006 ZB / 2.GPages: 264, PDF Size: 1.15 MB
Page 9 of 264
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A Word About Your Keys..................12
▫Ignition Key..........................12
▫Key-In-Ignition Reminder................13
▫Power Accessory Delay Feature............14
Door Locks............................14
▫Electronic Locking/Unlocking.............14
▫Mechanical Release.....................15
▫Automatic Door Locks...................16
Remote Keyless Entry.....................16▫To Unlock The Doors...................17
▫To Lock The Doors.....................18
▫To Unlock The Trunk/Liftgate.............18
▫Panic Alarm..........................18
▫To Use The Panic Alarm.................18
▫To Program Transmitters.................19
▫General Information....................19
▫Transmitter Battery Service...............20
Vehicle Theft Alarm......................21
2
Page 20 of 264
Transmitter Battery Service
The replacement battery number is 2016. This is a generic
battery, readily available at local retail stores.
1. Pry the transmitter halves apart with a coin or similar
object.2. Remove and replace the batteries.
3. Reassemble the transmitter case and test operation.
NOTE:If the transmitter is operated more than 255
times out of range of the vehicle (23 feet or 7 meters) or
when the vehicle battery is dead, it may become “out of
synch”. The result is that the transmitter will not func-
tion.
To correct this condition, remove the key from the
ignition and close the hood and all doors. Press both
buttons on the transmitter for about 10 seconds. The horn
will chirp once to acknowledge the signal. Normal trans-
mitter operation should resume.
Separating Transmitter Halves
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 76 of 264
On Coupe models there is an additional light for the
liftgate. The liftgate light and courtesy lights will turn
ON when the liftgate is opened. The liftgate light and
courtesy lights fade to OFF in about 4 seconds after the
liftgate is closed.
Interior Lights
The interior lights come on when a door, or liftgate
(Coupe models) is opened and the dome switch is not in
the defeat position. The interior lights will turn ON and
remain on for about 30 seconds then fade to OFF when
either of the following occurs:
•A door is opened using the outside door handle then
closed.
•A door is unlocked using the remote keyless entry
transmitter.
•A door is unlocked using the outside driver’s door key
cylinder.If a door is opened using the inside door handle the
interior lights will fade to OFF in about 4 seconds after
the door is closed.
Battery Saver Feature — Interior Lights
The interior courtesy lights come on when a door is open
or left ajar. To prevent battery drain, if you leave a door,
or liftgate (Coupe models) open or ajar with the ignition
key out or in the OFF/LOCK position, these lights will
turn off after 15 minutes. After you close the door, the
interior courtesy lights will again function in the normal
manner.
Multi-Function Control Lever
The Multi-Function Control Lever controls the operation
of the headlights, parking lights, turn signals, headlight
beam selection, instrument panel light dimming, interior
lights, the passing lights, and fog lights. The lever is
located on the left side of the steering column.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 79 of 264
Headlight Time Delay
This feature provides the safety of headlight illumination
for about 90 seconds.
To activate the delay, turn off the ignition while the
headlights are still on. Then turn off the headlights within
45 seconds. The delay interval begins when the headlamp
switch is turned off.
If the headlights are turned off before the ignition, they
will go off in the normal manner.
This feature can be disabled at the dealership if so
desired.
Battery Saver Feature — Exterior Lights
If an exterior light is left on when the ignition switch is
moved to the Off position (with the key in or out), it will
automatically turn off after 3 minutes. Normal operation
will resume when the ignition is turned On or when the
headlight switch is turned to another position.If the ignition switch is turned to any position other than
the Off position at any time during the 3 minute delay
period the battery saver feature will be disabled.
Fog Lights
The front fog light switch is on the Multi-Function
Control Lever. To activate the front fog lights, turn
on the parking lights or the low beam headlights
and pull out the end of the control lever.
NOTE:The fog lights will only operate with the head-
lights on low beam. Selecting high beam headlights will
turn off the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
3
Page 156 of 264
HAZARD WARNING FLASHER
The flasher switch is on the top of the steering
column, just behind the steering wheel. Depress
the flasher button and all front and rear directional
signals will flash. Depress the flasher button again to turn
the flashers off.Do not use this emergency warning system when the
vehicle is in motion. Use it when your vehicle is disabled
and is creating a safety hazard for other motorists.
If it is necessary to leave the vehicle to go for service, the
flasher system will continue to operate with the ignition
key removed.
NOTE:With extended use, the flasher may run down
your battery.
IF YOUR ENGINE OVERHEATS
In any of the following situations, you can reduce the
potential for overheating by taking the appropriate ac-
tion.
•On the highways —Slow down and use the highest
gear possible.
•In city traffic —While stopped, put the transmission
in neutral, but do not increase engine idle speed.
Hazard Flasher Switch
156 WHAT TO DO IN EMERGENCIES
Page 170 of 264
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Lamp)
is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system maynotbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery
replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.Your vehicle has a simple ignition key actuated test
which you can use prior to going to the test station. To
check if your vehicle’s OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn off the
170 MAINTAINING YOUR VEHICLE
Page 171 of 264
ignition key or start the engine. This means that your
vehicle’s OBD system isnot readyand you shouldnot
proceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn off the ignition key or start
the engine. This means that your vehicle’s OBD system
isreadyand you can proceed to the I/M station.
If your OBD system isnot ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
Regardless of whether your vehicle’s OBD system is
ready or not ready, if the MIL symbol is illuminated
during normal vehicle operation, you should have yourvehicle serviced before going to the I/M station. The I/M
station can fail your vehicle because the MIL symbol is on
with the engine running.
REPLACEMENT PARTS
Use of genuine Moparparts for normal/scheduled
maintenance and repairs is highly recommended to in-
sure the designed performance. Damage or failures
caused by the use of non-Moparparts for maintenance
and repairs will not be covered by the manufacturer’s
warranty.
DEALER SERVICE
Your dealer has the qualified service personnel, special
tools and equipment to perform all service operations in
an expert manner. Service Manuals are available which
include detailed service information for your vehicle.
Refer to these manuals before attempting any procedure
yourself.
MAINTAINING YOUR VEHICLE 171
7
Page 182 of 264
CAUTION!
It is essential when replacing the cables on the
battery that you attach the positive cable to the
positive post and the negative cable to the negative
post. Battery posts are marked positive (+) and
negative (-) and identified on the battery case. Cable
clamps should be tight on the terminal posts and
free of corrosion. Apply grease to post and clamps
after tightening. If using a “fast charger” while the
battery is in the vehicle, disconnect both vehicle
battery cables before connecting the charger to bat-
tery. Do not use a “fast charger” to provide starting
voltage.
Battery Save Feature
The Battery Save feature conserves battery power when
storing the vehicle up to 3 months without losing radio
and engine controller memory. This is an alternative to
disconnecting the battery.
NOTE:This vehicle is designed to sit in storage for up
to 30 days on a fully charged battery. If this vehicle is to
be stored for longer than 30 days the following is
recommended:
1. Disconnect the battery
2. Use the battery charger
3. Put the vehicle into Battery Save mode (3 month
charge).
Start the battery save feature by doing the following:
1. Insert the key into the ignition.
182 MAINTAINING YOUR VEHICLE
Page 183 of 264
2. Cycle the ignition from OFF to ACC four times with-
out going into ON. Leave the switch in the OFF position
after the fourth cycle.
3. Depress the driver’s side Power Door Lock switch in
the UP direction. A single chime and a horn chirp indicate
that the process has begun.4. Remove the key from the ignition and exit the vehicle.
5. The feature is cancelled when the ignition is cycled to
ON/RUN.
6. The vehicle will enter Battery Save Mode 45 seconds
after all doors are closed.
NOTE:The remote keyless entry and passenger exterior
door handle will not work when the Battery Save feature
is enabled. Enter the vehicle either by using the key to
open the door manually or by using the outside door
handle.
NOTE:The Vehicle Theft Alarm is disabled when the
vehicle is in Battery Save mode. Therefore, the vehicle is
not protected when the Battery Save feature is enabled.
NOTE:The exterior and interior lighting functions will
not work when the vehicle is in Battery Save Mode.
Exit Battery Save Mode by doing the following:
Ignition Key Positions
MAINTAINING YOUR VEHICLE 183
7
Page 184 of 264
1. Press the driver’s door exterior handle to wake up the
vehicle.
2. If the door does not open (vehicle is armed) press the
remote keyless entry unlock button to unlock the vehicle.
3. Press the driver’s door exterior handle again to open
the door.
4. Cycle the Ignition to ON/RUN. If the ignition is NOT
cycled to ON/RUN, then the vehicle will re-enter Battery
Save Mode 45 seconds after the driver’s door is closed.
Air Conditioner
Check the air conditioning system operation at the start
of the warm weather season.
NOTE:If air conditioning operation seems to be lower
than expected, check the front of the A/C condenser,
located in front of the radiator for dirt or insect accumu-
lation. Clean with a gentle water spray as required. Frontend fascia protectors may reduce air flow to the con-
denser and radiator, reducing A/C and engine cooling
performance.
WARNING!
•Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer
to Section 3 of the Warranty Information book for
further warranty information.
•The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced repairman.
184 MAINTAINING YOUR VEHICLE