power steering DODGE VIPER 2006 ZB / 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2006, Model line: VIPER, Model: DODGE VIPER 2006 ZB / 2.GPages: 264, PDF Size: 1.15 MB
Page 45 of 264
You should read the instructions provided with your
child restraint to make sure that you are using it properly.
2.All occupants should wear their lap and shoulder
belts properly.
3.The driver and passenger seats should be moved
back as far as practical to allow the airbags room to
inflate. Additionally, the pedals are power adjustable,
so the driver seat can be moved back and the pedals
moved closer as needed so the driver can be as far from
the airbag as possible. (See section on Power Adjust-
able Pedals for operation.)
4.You should read the instructions provided with your
child safety or booster seat to make sure that you are
using it properly.The airbag system consists of the following:
•Airbag control module and internal crash sensor
•AIRBAG Readiness Light
•Driver and Passenger Airbag/inflator Units
•Passenger Side Airbag On/Off Switch
•Passenger Airbag Off Indicator Light
•Unique Steering Wheel and Column
•Unique Instrument Panel
•Interconnecting Wiring
•Knee Impact Bolster
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
2
Page 99 of 264
FM Reception
Because FM transmission is based on frequency varia-
tions, interference that consists of amplitude variations
can be filtered out, leaving the reception relatively clear,
which is the major feature of FM radio.
NOTE:On vehicles so equipped the radio, steering
wheel radio controls and 6 disc CD/DVD changer will
remain active for up to 45 seconds after the ignition
switch has been turned off. Opening a vehicle front door
will cancel this feature.
SALES CODE RBQ—AM/FM STEREO RADIO
WITH6-DISCCDCHANGER
NOTE:The radio sales code is located on the lower left
side of your radio faceplate.Radio Operation
Power/Volume Control
Press the PWR/VOL control to turn the radio on. Turn
the volume control clockwise to increase the volume.
RBQ Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 99
4
Page 117 of 264
STARTING AND OPERATING
CONTENTS
Starting Procedures.....................119
▫If Engine Fails To Start.................120
▫After Starting........................122
Transmission Shifting....................122
▫Recommended Shift Speeds..............123
▫Skip Shift Light.......................123
Parking Brake.........................124
Brake System..........................125
▫Brake Pad Break-In....................129Power Steering........................129
Tire Safety Information...................130
▫Tire Markings........................130
▫Tire Identification Number (TIN)..........133
▫Tire Loading And Tire Pressure...........134
Tires—General Information................138
▫Tire Pressure.........................138
▫Tire Inflation Pressures.................139
▫Radial-Ply Tires......................141
5
Page 129 of 264
In the event power assist is lost for any reason (for
example, repeated brake applications with the engine
off), the brakes will still function. The effort required to
brake the vehicle will be much greater than that required
with the power system operating.
If either the front or rear hydraulic system loses normal
capability, the remaining system will still function with
some loss of overall braking effectiveness. This will be
evident by increased pedal travel during application,
greater pedal force required to slow or stop, and activa-
tion of the Brake Warning Lamp during brake use.
NOTE:Your Viper has a very high performance braking
system. The brake pads are a semi-metallic compound
which has been selected for superior fade resistance and
consistent operation. A compromise is that under some
weather and operating conditions, the brakes may squeal
slightly during light brake applications.Brake Pad Break-In
The brakes on your new Viper do not require a long
break-in period, but avoid repeated hard brake applica-
tions from high speeds during initial break-in. Also avoid
severe brake loading such as may be encountered when
descending long mountain grades.
POWER STEERING
The power assisted steering system of your vehicle
provides mechanical steering capability in the event
power assist is lost.
If for some reason the hydraulic pressure is interrupted,
it will still be possible to steer your vehicle. Under these
conditions you will observe a substantial increase in
steering effort.
STARTING AND OPERATING 129
5
Page 165 of 264
MAINTAINING YOUR VEHICLE
CONTENTS
8.3L Engine Compartment................168
Onboard Diagnostic System (OBD II).........169
Emissions Inspection And Maintenance
Programs............................170
Replacement Parts......................171
Dealer Service.........................171
Maintenance Procedures..................172
▫Engine Oil..........................172
▫Drive Belts — Check Condition And Tension . . 176▫Spark Plugs.........................176
▫Catalytic Converter....................176
▫Ignition Wiring System And Ignition Timing . . 178
▫Crankcase Emission Control System........178
▫Air Cleaner Filter.....................179
▫Maintenance-Free Battery................179
▫Battery Save Feature...................182
▫Air Conditioner......................184
▫Power Steering (Pump And Reservoir)......185
7
Page 166 of 264
▫Body Lubrication.....................186
▫Front And Rear Suspension Ball Joints......186
▫Steering Linkage......................187
▫Body Mechanism Lubrication.............187
▫Windshield Washers...................189
▫Exhaust System......................189
▫Cooling System.......................190
▫Hoses And Vacuum/Vapor Harnesses.......195
▫Brake System........................195
▫Brake, Power Steering, And Fuel System
Hoses.............................196
▫Brake And Clutch Fluid.................197
▫Master Cylinder......................197▫Hydraulic Clutch.....................198
▫Transmission........................198
▫Rear Axle...........................199
▫Wheel Bearings.......................200
▫Appearance Care.....................200
Fuses — Power Distribution Center..........203
Vehicle Storage........................208
Replacement Bulbs......................211
▫Interior Light Bulbs....................211
▫Exterior Light Bulbs — Convertible Models . . . 211
▫Exterior Light Bulbs — Coupe Models......212
Exterior Light Bulb Service................212
166 MAINTAINING YOUR VEHICLE
Page 185 of 264
Refrigerant Recovery and Recycling
R-134a Air Conditioning Refrigerant is a hydrofluorocar-
bon (HFC) that is endorsed by the Environmental Pro-
tection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by dealers or other service facilities
using recovery and recycling equipment.
NOTE:Use only manufacturer approved A/C System
Sealers, Stop Leak Products, Seal Conditioners, Compres-
sor Oil, or Refrigerants.
Power Steering (Pump and Reservoir)
WARNING!
Fluid level should be checked with the engine off to
prevent injury from moving parts. Do not overfill.
Use only the manufacturer’s recommended fluid.
Refer to Recommended Fluids, Lubricants and
Genuine Parts for correct fluid type.
Check power steering fluid level at intervals as specified
in the maintenance schedules.
During scheduled maintenance, check the power steering
fluid level at the power steering fluid reservoir.
The fluid should be checked HOT with the engine OFF.
MAINTAINING YOUR VEHICLE 185
7
Page 186 of 264
Before removing the reservoir cap, wipe the outside of
the cap and reservoir so that no dirt can fall into the
reservoir.
All power steering pumps have a dipstick. Fluid level
should be maintained at the proper level indicated on the
dipstick. If necessary, add fluid to restore to the proper
indicated level. With a clean cloth, wipe any spilled fluid
from all surfaces. Only petroleum fluids specially formu-
lated for minimum effect on the rubber hoses should be
used. Use only the manufacturer’s recommended fluid.
Refer to Recommended Fluids, Lubricants and Genuine
Parts for the correct fluid type.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should bewiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant or equivalent directly into the lock
cylinder.
Front and Rear Suspension Ball Joints
Your vehicle has suspension ball joints that require
periodic servicing. These ball joints should be inspected
whenever servicing a vehicle for other reasons.
186 MAINTAINING YOUR VEHICLE
Page 196 of 264
Brake, Power Steering, and Fuel System Hoses
When servicing the vehicle for scheduled maintenance,
inspect surface of hoses and nylon tubing for evidence of
heat and mechanical damage. Hard and brittle rubber,
cracking, checking, tears, cuts, abrasion, and excessive
swelling suggest deterioration of the rubber. Particular
attention should be made to examining those hose sur-
faces nearest to high heat sources, such as the exhaust
manifold.
Inspect all hose clamps and couplings to make sure they
are secure and no leaks are present.
Insure nylon tubing in these areas has not melted or
collapsed.
NOTE:Often, fluids are used during assembly plant
operations to ease the assembly of hoses to couplings.
Therefore, oil wetness at the hose-coupling area is not
necessarily an indication of leakage. Actual dripping ofhot fluid when systems are under pressure (during
vehicle operation) should be noted before hose is re-
placed based on leakage.
High pressure fuel system hoses have unique material
characteristics that provide adequate sealing and resist
attack by deteriorated gasoline.
Use only manufacturer specified hoses or their equiva-
lent in material and specification, in any fuel system
servicing. It is mandatory to replace all clamps that have
been loosened or removed during service.
NOTE:Inspection of brake hoses should be done when-
ever the brake system is serviced and at every engine oil
change. If there is any evidence of cracking, scuffing, or
worn spots, the hose should be replaced immediately!
Eventual deterioration of the hose can take place with
possible burst failure.
196 MAINTAINING YOUR VEHICLE
Page 222 of 264
Chassis
Component Fluid, Lubricant, or Genuine Part
Transmission Mopar Synthetic Manual Transmission Lubricant SAE 75W-85 (Castrol Syn-
torq LT 75W/85)
Rear Axle Mopar Synthetic Gear and Axle Lubricant SAE 75W-140 or equivalent, with
Limited Slip Additive Friction Modifier
Brake Master Cylinder MoparBrake & Clutch Fluid DOT 4 Motor Vehicle or equivalent.
Power Steering Reservoir MoparATF+4 Automatic Transmission Fluid or equivalent.
222 MAINTAINING YOUR VEHICLE