trip computer FIAT 500C 2015 2.G Owners Manual

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
INSTRUMENT PANEL FEATURES ..........139
 INSTRUMENT CLUSTER .................140
 INSTRUMENT CLUSTER — ECO ...........141
 INSTRUMENT CLUSTER — POP, LOUNGE,
500C ............................... .142
 INSTRUMENT CLUSTER DESCRIPTIONS .....143
 ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC) ............................. .155
▫ EVIC Displays ...................... .157
▫ EVIC Control Buttons ..................158 ▫
Electronic Vehicle Information Center (EVIC)
Setup Menu ........................ .159
▫ Change Engine Oil Indicator System ........160
▫ Trip Computer ...................... .161
▫ Trip Button ......................... .161
▫ Trip Functions ...................... .163
▫ Values Displayed ..................... .163
▫ Personal Settings (Customer-Programmable
Features) ........................... .164
 SALES CODE (RAB) RADIO ..............1774

INSTRUMENT PANEL FEATURES
1 — Side Vent7 — Passenger Air Bag13 — Storage Compartment
2 — Multifunction Lever – Light Control 8 — Glove Compartment14 — Shift Lever
3—
Instrument Cluster And Warning Lights9 — Rear Defrost Button 15 — Sport Button
4 — Windshield Wiper, Washer, Trip Computer 10 — Hazard Button 16 — Horn/Driver Airbag
5 — Central Air Vents 11 — Climate Controls
6 — Storage Compartment/Radio 12 — Power Windows Control
4
UNDERSTANDING YOUR INSTRUMENT PANEL 139

The EVIC consists of the following:
•System Status
• Vehicle Information Warning Message Displays
• Personal Settings (Customer-Programmable Features)
• Outside Temperature Display
• Trip Computer Functions
• Tire Pressure Monitoring Display
Electronic Vehicle Information Center (EVIC) Display
156 UNDERSTANDING YOUR INSTRUMENT PANEL

after a single chime has sounded to indicate the next
scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate, dependent
upon your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, push and
release theMENUbutton. To reset the oil change indica-
tor system (after performing the scheduled maintenance),
refer to the following procedure.
1. Turn the ignition switch to the ON position. (do not start the engine.)
2. Fully push the accelerator pedal slowly, three times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position. NOTE:
If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.
Trip Computer
The Trip Computer is located in the instrument cluster. It
features a driver-interactive display (displays informa-
tion such as trip information, range, fuel consumption,
average speed, and travel time).
Trip Button
The TRIP button, located on the right steering column
stalk, can be used to display and to reset the previously
described values.
• A short button push displays the different values.
• A long button push resets the system and then starts a
new trip.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 161

To cancel the setting, proceed as follows:
1. Briefly push and release theMENUbutton. “On” will
flash on the display.
2. Push and release the DOWN
button. “Off” will
flash on the display.
3. Briefly push and release the MENUbutton to go back
to the menu screen, or push and hold the MENU
button (approximately one second) to go back to the
main screen without storing the settings.
Trip B Data (Trip B On)
Through this option, it is possible to activate (On) or
deactivate (Off) the Trip B (partial trip) display.
For further information, see “Trip Computer.”
For activation / deactivation, proceed as follows:
1. Briefly push and release the MENUbutton. 2. Push and release the UP
or DOWNbutton to
select Trip B data. Push and release the UP
or
DOWN
buttons to turn ON or OFF
3. Briefly push and release the MENUbutton to go back
to the menu screen, or push and hold the MENU
button (approximately one second) to go back to the
main screen without storing the settings.
Set Time (Clock)
This function may be used to set the clock through two
submenu items: “Time” and “Mode.”
Proceed as follows:
1. Briefly push and release the MENUbutton. Push and
release the UP
or DOWNbuttons to highlight
Set Time — Push and release the MENU button.
2. Push and release the UPor DOWNbutton to
navigate the two sub-menu items.
166 UNDERSTANDING YOUR INSTRUMENT PANEL

NewTrip .............................162
Start Of Trip Procedure ...................162
Trip Computer ........................ .161
Trip Functions ........................ .163
Emergency, In Case Of Hazard Warning Flasher ..................303
Jacking .............................. .316
Jump Starting ......................... .329
Towing ............................. .337
Emission Control System Maintenance ..........347
Engine Air Cleaner .......................... .354
Break-In Recommendations .................73
Checking Oil Level ..................... .350
Compartment ...................... .345, 346
Cooling ............................. .366
Exhaust Gas Caution ..................75, 296
Fails To Start ......................... .225
Flooded, Starting ...................... .225Fuel Requirements
................292, 293, 398
Oil ............................. .350, 397
Oil Filler Cap ...................... .352, 353
Oil Selection ....................351, 352, 398
Oil Synthetic ......................... .353
Overheating .......................... .303
Starting ............................. .223
Enhanced Accident Response Feature .........49, 339
Euro Twin Clutch Transmission Fluid Type ........................... .374
Event Data Recorder ........................53
Exhaust Gas Caution ....................75, 296
Exhaust System ....................... .75, 363
Exterior Lights ........................ .78, 392
Filters Air Cleaner .......................... .354
Air Conditioning ...................... .357
Engine Fuel .......................... .398
424 INDEX